How to plaster door slopes with your own hands? Plastering slopes with your own hands: technology for puttingtying a doorway How to plaster door slopes

In this article I would like to by example talk about the procedure for this type of work such as plastering slopes front door. Sooner or later, almost everyone who decides to install a new entrance encounters this type of activity. metal door. And thanks to the tips listed below, you can do this yourself, without resorting to the help of specialists.

So, you have a new front door installed. Naturally, this is a joyful event, because the front door is, first of all, the protection of your home. But along with joyful emotions, you will certainly be faced with the question “What is the next step?”, because when dismantling the old and installing a new entrance door, the slopes suffer the most.

And this problem cannot be avoided, because... This is the specificity of this type of work. But despite this, there is no need to despair. Modern variety finishing materials allows you to solve this issue “smoothly” and quickly.

Preparing the destroyed opening for finishing

Before proceeding directly to finishing the slopes of the front door, you need to prepare the opening itself. First of all, it is necessary to get rid of all dust, remnants of bricks or pieces of chipped plaster, remove excess polyurethane foam, which can be easily removed using a regular stationery knife. When the slopes are prepared, you can move on to the next stage.

Choosing material for repair

Market building materials very rich today.

The slopes can be plastered again;
glue sandwich panels or use PVC panels;
resort to using drywall or wallpaper;
can be used as decoration natural stone or other decorative materials.

Finishing materials are presented to suit every taste and, of course, budget. And each material has its own advantages and qualities. And the cheapest and simplest is still plaster. It holds heat well and has good soundproofing qualities. Using plaster, slopes can be made straight at an angle of 90 degrees or turned.

So, we buy gypsum plaster mixture. It can be diluted in a regular basin.

And so that it mixes well, we use a special attachment - a mixer on a drill. We bring the mixture to the desired consistency (with the help of water, of course) and you can move on to the next “act”.

Let's get started

The initial stage of work on plastering slopes is, to put it simply and in clear language, in "throwing" ready mixture on the slopes themselves.

This operation is not difficult to perform; it is enough to use a regular spatula and skill. The amount of putty mixture will depend on how much your door slopes are “damaged”. This issue can only be resolved individually and on the spot.

When this work done, level the slopes with a wide spatula and make something like small notches.

Of course, you shouldn’t be too zealous, but you can show a little imagination. This will simplify the next stage of applying the putty mixture. Putty applied to the first layer will adhere better precisely thanks to these notches. It will seem to “cling” to the first layer, which will provide us with a good result.

At first glance, the work of plastering the slopes of the front door is not so difficult, and you can do it yourself. The main thing is to have the desire and ability to handle simple and familiar tools. But even such work has its pitfalls.

For example, it will be difficult for a beginner to “throw” the mixture onto the upper slope. Therefore, you should not take it right away large number mixture, it is better to use a small amount to start with. And one more little tip: to make the plastering smooth and neat, you can walk along the slopes with a brush dipped in water at the end of the work.

The only drawback, in my opinion, of using a gypsum-plaster mixture to finish the slopes of the front door is that it takes a long time to dry. But the end result will certainly make up for this “gap”.

The work done in this way will bring your front door to proper condition. But you don’t have to stop there and continue decorating the slopes at your discretion.

Windows are a source of light, important detail interior of the house, therefore, to give them a complete look, slope plaster is used. It will not only hide traces of installation of window systems and level the surface adjacent to them, but will also significantly reduce heat loss in the room and give the room a harmonious and neat appearance.

We will tell you in this article how to choose the right materials and design window and door slopes so that it is of high quality and beautiful.

Features of the design of window/door openings

There are several simple ways finishing of internal slopes of doors and windows is covering with plastic, plasterboard, wood. These materials allow you to quickly level and at the same time decorate the surface, but in the most quality option is plastering of slopes with cement mortar. It allows you to get a slope various widths, shapes, which is especially important for arched and round structures.

Note: Although plastering window slopes is a dusty, labor-intensive task, it allows you to achieve absolute tightness (the finishing layer becomes part of the wall, which cannot be achieved when covering it with plastic and plasterboard).

Technology for rough finishing of internal and external window slopes

Plastering of slopes is carried out after installing and fixing windows and doors, as well as rough finishing of the walls of the room. It could be:

simple (lime, cement, clay);
complex (gypsum, clay, or cement-lime).

Attention: For interior works A gypsum or lime mixture is used; external slopes are plastered only with cement mortar.

The composition of the leveling mixture depends on the location of windows and doors, and the humidity in the room

Preparatory work

Before plastering window slopes with your own hands, you should remove dust, eliminate gaps and cracks in the wall. It is most convenient to seal them with polyurethane foam, but you can also use tow and felt. Immediately before applying the leveling mixture, the walls are impregnated with a primer.

Advice: if the width of the seams between the window and the panel is more than 4 cm, you will need to make notches on the wall and reinforce the seam with reinforcing mesh to improve adhesion to the mortar.

Filling cracks with foam

Slope leveling

How to make slopes on plaster windows? For cosmetic or major renovation in a universal way is the finishing of slopes “to the rule”, carried out according to beacons. Beacons are fixed in the corners using mortar, along which the surfaces of the opening will be leveled.

Recommendation: As a rule, it is better to fix it with dowels, and check the evenness of its installation with a level.

Attaching the guide bar

The solution is applied to one of the sides, leveling it using a fine mortar. It is recommended to start from the top slope, then move to the side slopes, and finish with the bottom slope.

Attention: During the work, it is necessary to cover the window with film so that the solution does not get into it.

Decorating a window opening - leveling slopes with plaster

When the mixture dries, carefully remove the guide rail. Next, the corners are corrected, the surface is treated with a grater, removing the remaining solution.

Advice: The window profile for plastering slopes will significantly speed up the work. It simultaneously serves as a guide for leveling surfaces, protects the frame from contamination, and prevents the appearance of cracks.

The window profile will greatly facilitate the work of decorating the opening.

A clear example of how plastering is done door slopes do it yourself - video:

After finishing the internal slopes, they begin to work on the external ones. If left untreated, the polyurethane foam will deteriorate over time under the influence of atmospheric conditions, which can cause window deformation and damage to the walls of the building.

The finishing of the external sides of the window opening is carried out similarly to the internal ones.

External plastering of window slopes - video:

Technology for rough finishing of door slopes

How to level a doorway with plaster? On preparatory stage the cracks are filled with polyurethane foam. For plaster, it is preferable to use a mixture prepared in a ratio of 1:3 (cement + sand).

To external corners doorway have not chipped over time; they should be reinforced with a special metal angle strip. For this, a 60 mm profile is used, which is attached to the plaster mixture at a level along the entire perimeter of the door.

How to plaster door slopes? This question interests a lot of people when installing new door, and during repairs. The service life of the doorway directly depends on the quality of work.

In order for the doorway to serve you for many years, you need to pay great attention to the correct creation of slopes. Today you can find the most various materials in order to make door slopes of the highest quality, practical and, of course, beautiful. The most popular materials include:

Drywall that can quickly solve problems uneven surface. The main advantage of using this material is that you do not need to build a frame installation to create slopes.
Plastic. These products should only be used if you have installed them in your home plastic doors. If you want to combine PVC with other materials, be prepared that the slopes will stand out very much against the background of such doors.
Natural wood. Wood, of course, goes well with almost any interior, but creating such slopes can cost you quite a lot, because the price of natural wood is quite high.
The cheapest and quick method creating slopes is their plastering. In addition, plastering has other advantages: high level strength, long term operation and low price. In this case, you just need to cover the slopes with plaster, after which the products have dried, you can paint, varnish or choose another finishing method.

Today we will talk about how to plaster door slopes. We’ll also tell you how to carry out a finishing touch so that the slopes look great.

Like any finishing work, plastering of door slopes is carried out using certain materials. When preparing a plaster mixture, you should not skimp on cement; otherwise, after a while, the coating may simply fall off. The most optimal proportion is to prepare a composition of 1 part cement and 3 parts sand, and it is best to use river sand, which contains minimum quantity clay

If finishing is carried out indoors, then it is better to prepare a mixture with a small amount of alabaster - it will make it easier to work with the upper slopes. This point is especially important if the jumpers have a curved shape. This is why a large thickness of the coating of the composition is so important - so that the mixture can stick to such difficult places. For reliability, you can use masonry mesh. Before starting work directly, you need, as you already understood, to purchase necessary tools and make preparations.

So, be sure to clean the base, removing paint, wallpaper or other finishing materials, remove old plaster, and thoroughly clean stains and dirt using a soap solution and degreasers. Very important stage is a surface primer that not only provides high-quality adhesion, but also prevents the spread of pathogenic bacteria and rot that can appear under the plaster as a result of temperature changes or high humidity.

To carry out this stage, it is advisable to use a primer deep penetration or focus on the material from which the base is made (concrete, wood, drywall, brick).

How to plaster door slopes - step-by-step diagram

Step 1: Installation of beacons

To mount beacons, use either aluminum profiles or flat wooden slats, which are installed using alabaster or secured with self-tapping screws. The main thing is to use a building level so that the slats are parallel to each other, otherwise the slopes will turn out crooked.

Step 2: Creating Notches

In fact, plastering the door slopes is not the very last step in upgrading the doorway. Undoubtedly, many people end up with simple plaster, but there are other methods that will give the surface a more aesthetic appearance.. Naturally, the choice of materials in this case depends on the interior of your home. When choosing materials, also rely on the recommendations below:

If we are talking about internal slopes, it should be borne in mind that they will be exposed to dirt and dust, and therefore the material for the slopes in this case must be well cleaned.
When talking about entrance doors, especially in a private house, you should remember that the slopes will be exposed to moisture - temperature changes inside and outside the room often lead to the formation of condensation. Some finishing materials do not perceive moisture at all or quickly deteriorate under its influence. In this case, it is advisable not to use gypsum board sheets and wood.
Do not forget that slopes may be subject to mechanical impact, which also needs to be taken into account. That is why it is undesirable to use for entrance doors plastic products, which are very easy to damage.

We told you how to plaster door slopes, which means it’s time to improve the appearance of your home, because doors play an important role in this.

How long the door frame will last depends on the quality of plastering of the slopes. Let's figure out how to quickly and efficiently plaster door slopes yourself and how to save money on doing this work yourself.

Plastering slopes – necessary work on finishing the doorway after installing a new one door frame. The appearance and trouble-free service life of the door directly depend on how well the slopes are finished. To do these jobs correctly, you need a certain skill. But it is still quite possible to plaster door slopes with your own hands. Let's figure out how this is done.

Why are slopes trimmed?

First of all, let’s find out what problems slope processing should solve. This operation is performed due to a number of reasons:

Preservation of heat and protection from extraneous noise. A layer of plaster hides all the cracks, so warm air no longer blown away by drafts. Extraneous sounds It is also more difficult to get into the room if the slopes are properly sealed.
UV protection. Ultraviolet rays exposed to sunlight gradually cause degradation of the polyurethane foam. The layer of plaster prevents the impact of UV rays on the polyurethane foam, which means the durability of the door and door frame increases.
Finishing and giving a complete look. Sealed slopes have a much more aesthetic appearance. Therefore, only after completing the plastering work can we definitively say that the door is installed in place.
Basis for further finishing works. To install panels or paint a wall, you must first carefully level it, remove all differences in height, cracks, and cavities. These tasks are performed by plastering work.

That is why, after installing the doors, it is necessary to finish the slopes with the utmost care. It is quite possible to handle this work on your own. But you need to prepare everything you need and master the technology for performing the work.

Selecting materials

To create a layer of plaster, you can use various building compounds. All components for their manufacture can be purchased at construction stores. Here are the most common options for solutions for finishing slopes:

A mixture based on cement and sand. A classic plaster material that fully meets the “cheap and cheerful” principle. It is quite simple to make: take part of the cement, mix it with water (it needs a little less in volume) and mix it with three to four parts of pitch. The amount of sand is selected according to the concentration: it should resemble thick sour cream.
Slopes finished with a cement-sand mixture do not look very aesthetically pleasing. Therefore, this option is most suitable as a basis for subsequent finishing.
Cement-sand composition with the addition of alabaster. Alabaster, gypsum and other similar additives allow the finished substance to harden faster; in addition, the solution becomes more plastic.
Ready-made mixtures for plastering slopes. As an example, let's name mixtures from the Knauf company: Rotband gypsum plaster and MP-74 mixture. But you can also take mixtures of similar purposes produced by other manufacturers. The advantage of this choice is good qualities solution and a fairly aesthetic appearance of the finished surface. The downside is the higher price.

It is difficult to definitely recommend one or another version of the mixture for plaster. The choice is made based on the budget allocated for these works, the personal preferences of the master and the purpose of the finished surface (i.e. whether subsequent fine finishing or not).

Required materials and tools

For the job to go smoothly, it is important to have the right tools to complete it. Let's figure out what you need to plaster slopes with your own hands and how to choose the right tool.

First of all, you will need to prepare the level. It is better if there are at least 2 ampoules on it. When choosing a length, it is better to choose a tool about 1 m long. A shorter one will be inconvenient to work with (you will have to shift it too often and there is a higher risk of creating “steps”), and with a long tool it will be impossible to turn around between the walls and the jamb.

For marking you will need a tape measure (a 2-meter tape measure is enough) and a simple pencil with a protractor. To bring out the surfaces in an optimal way, you will need an aluminum rule.

To prepare the solution and apply it to the wall, you need to prepare:

A vessel for preparing the mixture.
A measuring stick for measuring volumes.
Dishes for water.
Tools for applying the finished mixture to the walls: a spatula (5 cm), a trowel (the kind used by masons), a trowel and graters (if you plan to plaster with cement-based mixtures). If you plan to use it on gypsum base, instead of a grater and graters will be needed wide spatula(45 cm), smoother and grater with a sponge base.
Hammer-pick.

You will also need to take care of protective equipment. Mixtures based on gypsum and cement have a very aggressive effect on the skin of the hands. Therefore, you need to take care of gloves (a medical sample will be enough). You will also need a work coat or other protective clothing. To avoid dusting your eyes and hair when working, you should also choose a hat and safety glasses.

Another aspect safe work– reliable support for the feet. Avoid working from wobbly stools or chairs. A reliable stepladder – already a little more suitable option, but it will have to be rearranged often, and your legs will get tired from working in a narrow area. Therefore, if possible, it is worth putting together comfortable sawhorses.

Preparatory work

Work on plastering slopes must be carried out as carefully as possible. The door, when closing and opening (especially with sudden impacts), transmits vibration to the frame, so poorly applied plaster can simply fall off. Therefore, if you want to avoid the need for repairs for as long as possible, you need to complete all the work as carefully as possible and prepare the walls well for work.

The door frame is installed even before finishing work on the slopes begins. This way the structure will be more durable, and there will be no need to fill the gaps between the wall and the slopes. When installing, be sure to use a level to check that the box is as level as possible vertically and horizontally. If necessary, use wooden wedges for adjustment.

Before starting work, do not forget to protect door leaf and jambs from getting hit building mixtures. You can seal the protected surfaces with tape, cover them with newspapers or plastic film.

First you need to prepare the surfaces in a rough form. For this, old plaster and pieces of bricks protruding beyond the slope are removed. You can beat them off manually or use a hammer drill.

The next step is to remove dirt and residues cement mixture. Use a wet rag or spatula to remove all deposits from the brick or concrete slab. The more carefully this stage is completed, the less the risk that the plaster will fall off along with the dirt.

Before applying plaster, you need to wait for the cleaned walls to dry thoroughly. Only then can you begin plastering work.

How to plaster door slopes. Step by step instructions

Execute plastering work It’s not very difficult to do it yourself on door slopes. But the technology must be strictly followed. Here are the basic steps to work with:

We evaluate the surface and determine approximately how much solution will have to be applied. If necessary (if you have to put a lot of mortar), a mesh with 10 by 10 cm cells is nailed to the wall. The mesh will allow the mortar to lie more evenly and hold more firmly.
The slope is strengthened with an angle made of perforated light alloy aluminum profile. The corner is fixed with cement mortar and leveled so that its edge does not protrude from the wall. The squeezed out solution is removed.
Protruding fragments of polyurethane foam are cut off with a knife and protected from moisture. To do this, a layer of vapor barrier sealant or film is applied to it.
The surfaces are treated with a primer so that the plaster adheres better. The type of soil is selected based on the used plaster composition and wall material.
After the surface has dried thoroughly, begin plastering. Apply the mortar onto the wall using a spatula and level it, removing excess mortar. You need to pay special attention to the condition of the corners. Typically, plastering is carried out in two stages: rough and finishing. Enough time should pass between the two stages for the solution to set well. You can wait even a day.
When the finishing layer dries, the plaster is thoroughly rubbed, achieving a smooth surface.

By following these steps, you can get perfectly smooth slopes with your own hands.

Every business requires practical experience. Therefore, advice from craftsmen who perform finishing work professionally is especially valuable. Here's what professional finishers advise:

Finishing the slopes is an important stage, the quality of which directly determines the service life of the door. But if you study the technology and prepare everything you need, you can do it yourself even with minimal finishing skills.

Give door slopes high-quality surface allows plastering. Since many rooms housing stock have plastered walls (this is a logical point), plastering of window and door slopes is carried out in a similar way. The method of plastering slopes is accessible even to a beginner. The main thing is to prepare all the necessary tools.

After installing the door, you need to plaster the slopes, this will give a beautiful, neat look.

Carry out substitution door designs so that their finishing is not required is not possible, since the removal of unnecessary frames involves the removal of old layers of plaster. This may leave chips and cracks in the door openings. The distance between the walls and door frames is filled by suitable material, which should fit more tightly into each crack. Next, the surface should be carefully cleaned of dirt, old paint, dust and soot.

Stages of plastering door slopes

Before plastering begins, a line for the location of the slope is drawn.

Before plastering the door slopes, the wall should be leveled. The door is usually installed after leveling the wall where necessary. When the door is already installed, the wall is aligned on the desired side. They start by measuring the corners, taking into account the height of the side door slopes, not forgetting about the upper slope.

The walls near the door slopes must be carefully plastered and rubbed. Before work, rules are hung on the slopes in their upper part, which must be hung on each of the sides strictly vertically. The plaster solution is applied with a spatula, starting from bottom to top.

If you need to make several layers, then you need to dry them one by one before applying each next layer. Plaster is applied to door slopes not only to create an even layer, but also an attractive one. appearance. At the same time, they are able to provide additional heat and sound insulation.

Depending on the location of the door, the appropriate type of plaster is selected.

It can be external or internal. The technology for plastering door slopes comes down to the following operating principles:

Making a template for removing excess plaster is made from plywood or chipboard.

The door is installed at the same level, and the side parts of the door frame are located on the left and right at an even distance from the walls.
The cracks should be caulked with pre-prepared insulation, which must be carefully filled in all the cracks.
You can treat felt with tow with a 3% solution of potassium fluoride.
Before plastering, the surface of the door slopes is cleaned and metal pendulum strips are installed, which help level the surface to the maximum.
can be produced using the starting facade plaster or cement mortar.
When plastering external slopes doors, the solution must contain various impurities to extend the life of the solution.
The choice of type of plaster is carried out for certain type premises - residential or non-residential.

The process of grouting the plaster is carried out in a “quick-up” manner, and the rules can be removed only after the grouting is done. Side slopes must have a segment small size, the sharp appendage of which should have a length of 20-30 cm. Rounded or flat chamfers should be made at the bottom.

What tools and materials will be needed?

Carrying out all work related to plastering window and door slopes requires increased care and extreme accuracy. Beginners who have never practiced before can also do this. similar types works All requirements related to the rules for finishing work are strictly defined. Compliance with them will allow you to qualitatively design the surface of the door slopes, as well as save money.

The finished door slope should have a neat even layer plaster, and this can be achieved if there is the following materials and tools:

Tools and devices for plastering slopes.

drill with attachment;
two-meter building level;
rule;
a spatula whose width exceeds the width of the slope;
flat brush for priming the surface;
perforated metal corners to protect external corners;
polyurethane foam;
glue “liquid nails”;
fiberglass plaster mesh;
perforated corners with mesh;
masking tape;
fine sandpaper.

The solution should be prepared using dry gypsum plaster, which must be diluted to a certain consistency. If you use polystyrene foam, you can save solution. If there are deep potholes in the slope, the foam used is laid in pieces in those places that are deeper. This must also be done when the thickness of the door slope is more than 2 cm.

The door frame will not be damaged if you cover its surface with masking tape. They begin to prime and plaster only after this. At the final stage, a rough finishing is carried out using sandpaper, after which the surface is primed.

How to properly plaster door slopes?

Image 1. To make the corner even, install a perforated corner.

Finishing of slopes is carried out using a solution of cement and sand. First, prepare the surface: first remove all remnants of outdated layers of putty and paint, and then remove the old plaster. When a layer of plaster is firmly attached, special notches are made on it to improve the quality of adhesion of the next layers to the door slopes. Then it is necessary to moisten the base with water in order to apply a solution of cement and sand.

To completely eliminate all defects, use a grater. Along the edges window openings you should install slats that act as guides. It is necessary to keep under control the level of verticality of the slopes, which is associated with their evenness. Further work should be carried out by analogy with finishing the upper slope.

Before plastering, the surface must be treated with a layer of “Betonokontakt” primer or another, which must be diluted in a small amount of water, by installing a perforated corner with a mesh (image 1) and a level upper slope.

To ensure that the corner does not stand out on the flat surface of the wall, the plaster is cut with a knife to a depth of 3 mm. Using a level applied to the surface of the wall and a knife, a horizontal line is drawn. After this, the plaster is removed from the end. The resulting recess is used to install the corner.

The installation of perforated corners on the “Rotband” is carried out in a similar way. You should use a level that is applied to check the verticality of the installation. Perforated corners You can perfectly protect the outer corners of door slopes, which will later serve as beacons during plastering.

To ensure even application of plaster, a special rule can be set on the slope.

You can use small nails to secure the corners. The main thing is to make sure that they cannot move. To do this, first measure the horizontal and vertical using a building level. If the vertical is violated, a piece of drywall is usually placed, which will allow the corner to be evenly strengthened.

After leveling the wall and fixing the corners with a spatula, begin. To do this, you can use “Rotband” plaster, which has excellent qualities. It should be mixed with water in the required proportions manually or with a drill with a special attachment. This will create a mixture that won't run off.

If necessary, you can apply a thick layer of plaster. Plastering technology involves initially throwing on a layer of plaster and then drying it. This will give it strength and the layer will not fall off. Then the door slopes and corners are removed, rubbing the surface completely.

If the slopes are uneven and the size of the mortar layer is more than 1 cm, then a special mesh is used. This is due to the appearance of cracks on the surfaces. Therefore, you will have to start doing all the work all over again. It is better to start plastering from the top in order to get a certain type of beam resting on both posts. This way you can increase the strength of the slopes. In this case, pieces of plaster will not fall off.

The upper tier should be reinforced with a rail, which should be installed on the plane of the doorway from above. This will allow you to rely on it as a rule that can be used to remove excess solution. Then the layer of mortar must be left to dry, and later removed using a rule and smoothing the surface of the slope, which may be covered with various defects, such as holes or other types of irregularities. To eliminate them, it is necessary to leave the plane of the door slopes to dry for a certain time.

The rules are attached at equal distances from each other along the entire height of the slope.

It is permissible to use a certain trick, which is related to ensuring that the surface of the frame is not hidden under a layer cement mortar completely and a certain part of it was outside. Therefore, the lath must have a cut precisely in certain place, which refers to the frame. In this case, adjustment is possible due to the certain depth of this cut, as well as the height to which the window frame protrudes from under the layers of plaster.

What should you pay special attention to?

Plaster consumption table.

Slopes should be plastered after waiting completely dry plaster solution, because when accelerated process As a result of evaporation, the mixture with cement will not become stronger, but will become covered with cracks. When plastering, you should create protection from drafts.

A layer of plaster applied to the door slopes will give them an even appearance, which will be associated with the creation of a layer of heat and sound insulation. The type of mixture for plaster is chosen based on the method of installing the door, which can be internal or external. For example, it is better to treat slopes leading to a bathroom or sauna with a cement-based solution, and interior spaces must be treated with lime-gypsum mortar.

When subsequently installing doors, you must ensure that the location of both parts of the door frame is at an equal distance from the opposite walls. The doors should be installed at the same level, and the cracks in the resulting openings should be sealed with felt, tow or polyurethane foam.

Then steel beacon strips are installed to help level the surface. Both the first and second beacons should be installed at the same level and at an equal distance from the location of the door frame. Plaster is applied in a number of steps, their number is determined by the size of the layer thickness.

Image 2. The plaster is sanded using a sanding belt holder.

If plastering of external door slopes is required, then water-repellent admixtures are added to the cement solution, which protect against moisture penetration. This extends the useful life of the cement mixture.

The choice of mortar for plaster must be explained by the fact that not every mixture is suitable in its properties for finishing residential premises. Therefore, it is necessary to carefully study the instructions on the packaging, while simultaneously consulting with the sales administrators of the company selling this type finishing material, or with sellers in the store.

After the plaster has completely dried, the surface begins to be cleaned using a sanding belt holder, to which is attached an abrasive mesh sheet (image 2), used instead of sandpaper. After this, the surface is covered finishing putty and paint.