How to calculate a frame house 6 6. How to make an approximate calculation of the cost of building a frame house. Materials you will need to build a roof

During construction frame house An important and responsible step is the preparation of material for the walls of the house. To build the walls of a frame house, we will need the following building materials:

Timber for the construction of vertical posts, horizontal connecting jumpers of the frame;

Edged board;

Heat and sound insulation;

Polyurethane foam;

Waterproofing - roofing felt;

Fastening material (staples, nails, etc.).

We calculate the amount of building material for constructing the walls of a frame house based on the size of the future building. For example, it is necessary to build the walls of a frame house with the following parameters: height - 2.8 m; length - 10 m; width - 8 m.

Based on these data, we calculate the number of vertical posts of the house frame. The total length of the walls of the house will be (2x10 m + 2x8 m), that is, the perimeter of the house is 36 meters. Racks for the walls of the house must be placed in increments of 50 cm, and it must be taken into account that in the locations window openings the distance between the posts must be at least 1.2 meters.

Thus, for the racks of the house frame you will need approximately 4 m3 of timber with a cross section of at least 100x150 mm. For connecting posts into a frame and final connection wall frames you will need at least another 3 m3 of such timber. In total, to make the frame of the walls of the house you will need 7 m3 of 100x150 mm timber.

Edged boards are used to cover the frame. The amount of edged boards that will be needed to cover the walls of the house (length -3 m, thickness -25 mm, width -150 mm) -4.65 cubic meters. meters. In this case, windows and doors are not taken into account; their size and quantity depend on the desire of the developer. Insulation and sound insulation are calculated based on their technical parameters.

Technology for erecting walls of a frame house.

The construction of walls begins with the installation of an insulating substrate, for example roofing felt. The roofing material is laid on the surface of the foundation, after which the embedded beam is laid on it. The beams in the corners are connected to each other “in a paw” - cutting out half the thickness of the beam at the ends. For rigidity, in advance drilled hole A dowel is driven in at the joints.

The base of the frame is laid in height equal height two embedded beams. After laying the embedded beams, a cut is made in the upper beam with a depth of half the beam. In this case, the number of “seats” corresponds to the number of frame racks.

The racks, prepared at a given height, are installed in the prepared “seating” places (grooves) and secured with temporary jibs. After all the racks are installed, the upper beam is attached to the top; the upper ends of the racks are inserted into the grooves cut in advance in the upper beam. The distance between the grooves in the upper beam is the same as in the lower one.

To add rigidity to the structure, the racks are attached using jibs, after which all temporary jibs are removed from the boards.

Longitudinal beams made of timber are also attached groove to groove, and pulled together using nails no less than 100 mm long. After this you can sheathe outer wall edged boards- with a continuous “shield”, leaving only openings for windows and doors, insulation is laid and everything is sewn up again with boards. Frame walls The houses are ready, you can proceed to the construction of the floor and roof of the house.

Beautiful and durable frame buildings produced by our company have been delighting their owners with impeccable quality for many years. appearance and excellent performance characteristics. These are 1- and 2-story comfortable cottages “Bavaria”, “Bungalow”, “Villa”, “Zvenigorod”, “Radonezh”, “Stockholm”, “Tetris”, “Estate” and “Chalet”. All of them are built taking into account all requirements for modern technologies, but the cost of buildings even within the same series is not the same.

What affects the price

What determines the cost of building a house? From such important factors as:

number of storeys;
roof type;
second light;
building area;
distance from the Moscow Ring Road;
dimensions (length and width);
the presence or absence of an attic;
the presence of a terrace, balconies, parking space;
the desired number of bedrooms on the first or second floor in the commissioned housing;
use of siding, brick, blockhouse, facade panels when producing finishing works.

Using an online frame house calculator, the customer can independently determine the amount that will be spent on its construction. The future owner of a reliable and durable structure determines the need for internal finishing, installation of plumbing equipment, water supply and sewerage. The installation of heating, electrical, and natural ventilation systems is also calculated.

How to use an online calculator

A free calculator for calculating a frame house online is a convenient program that allows you to quickly, without extra costs time, determine estimated cost carrying out construction work. Anyone can use the service. It is especially in demand when performing work on an individual project.

To find out the cost of the work, you must fill in all the fields provided and then indicate the address email and a telephone number to receive a calculation and clarify the configuration (“Lite”, “Basic”, “Economy”, “Comfort”, “Comfort”). After processing by our company’s specialists, the information is immediately sent to the specified email, and the customer has the opportunity to plan their expenses. Having such information greatly simplifies and speeds up the process of constructing a frame structure.

"BAKO" - convenience, comfort, professional approach to business.

According to the data obtained as a result sociological survey, the majority of residents of almost all regions of our country dream of building their own home, while a significant part of those surveyed plan to do this in the near future and live in their new home permanently. Besides this option, several answers concern construction small houses outside the city, which will be allocated for a dacha. And only a small part of respondents are satisfied with their current living in a city apartment. But despite plans, not everyone achieves their goals in a short time. In most cases, this is due to a lack of financial resources and time. That is why, before starting this activity, it is necessary to calculate the materials and, of course, their prices for the construction of a frame house.

Before you start building a frame structure, you need to calculate all the materials.

Materials required for the construction of a frame building

In most cases, frame houses do not differ too much large sizes, accordingly, constructing them will be quite simple. And this will significantly affect the amount of materials. Yes, unlike large quantity houses built using other technologies do not cost as much money. On average, in order to build a dwelling of 100 square meters. m, you will need to spend on building materials no more than half a million rubles. So, what exactly is included in the set of materials needed for this type of construction? This list consists of the following materials on frame house:

Timber is the main material from which frame structures are made. Timber intended for construction must be treated with septic tanks and water-repellent compounds.

edged board for sheathing walls;
wooden beam;
polyurethane foam;
nails;
hammer;
staples;
self-tapping screws;
screwdriver;
insulation;
waterproofing.

The main thing in the process of selecting and calculating materials is the structure itself. Therefore, all calculations will be based on the dimensions of the future home. They are usually specified in the construction documents. In order for the calculation to be most accurate, it is necessary to determine the dimensions of the house frame, in particular the cross-section of materials and the spacing of their arrangement.

In addition, it would not hurt to draw up a plan that will reflect all the components of a particular structure and take into account almost everything necessary.

When making accurate calculations for purchasing materials, you still need to buy everything with a reserve so that you definitely have enough.

But you still can’t be 100% sure that it’s correct, so even if you’re fully confident that you’ve calculated everything correctly, you still need to purchase a little more materials. This will allow you not to worry that something is missing, or that this or that material will not fit in size. Otherwise, the construction process will have to be interrupted, which will lead to a delay in the delivery of the project. In addition, it is possible that the sizes you need will no longer be in stock. Then you will also have to wait until the sawmill produces the lumber of the sizes you need.

Return to contents

Calculation of the cross-section of materials for a frame house

For an ordinary house, the length of boards and bars is on average 3-5 m.

The frame of this type of house consists exclusively of lumber. In this case, all elements must be cleared of bark and possible plaque, sawn into boards, bars or slats. For a standard house, the length of the bars and boards is on average 3-5 m, but special-sized material can also be ordered at the sawmill. So, here you can make one and a half meter and six meter materials for a frame house. You shouldn't save money here, even if you are offered a discount. Correct sizes will guarantee that your home will last much longer and more efficiently. If you purchase shorter materials, the rafters, posts and beams will have to be assembled from several small parts. As a result bearing capacity the structure will be significantly reduced. In order to avoid this, you will have to build a frame with overlapping boards and bars on top of each other. As a result, there will be no savings, and instead of saving money, you will have to buy additional lumber once again. Depending on which particular frame element you need to calculate, its individual indicators will differ from others.

Return to contents

Calculation of material sizes for the lower and upper framing of the frame

The main elements that you should pay special attention to include length, cross-section and materials necessary for fastening. The cross-section depends on what kind of insulation you intend to use during the construction of the house. If, for example, you use insulation with a thickness of at least 15 cm, then the section will have a width of 15 cm, while the height of the section should be at least 10 cm. The best option, of course, is a solid block of the dimensions indicated above, but if This is not feasible, then you can knock together one block from two smaller ones. The length of this part depends on the dimensions of the foundation. Accordingly, by measuring its length, you will get the total length of the bars necessary to strap the lower part of the house frame.

For fastening of this element It is best to use anchor bolts to the foundation. Their diameter should be approximately 30-32 mm. Or these fasteners can be replaced with studs, which are inserted into the foundation before it hardens. Their thread should also be the same as the size of the above bolts. They, in turn, can also be attached to the foundation in advance or after it has strengthened. The studs must be selected in such a way that they are concrete surface they were at a height of approximately 15 cm, so the minimum length of the pin used in the tying process will be 30-35 cm. Despite the fact that in construction stores this product presented in more impressive sizes (at least 1 m), you will need to purchase a maximum of 3 studs to strap the lower part of the frame of a house with an area of 100 sq.m.

In order to fasten the harness, it is necessary to connect the bars together. Nails or pins are used for these purposes. Moreover, for each corner you will need one nail with a length of at least 15 cm, and a thickness (diameter) of approximately 0.5 cm. The dimensions and quantity of materials for the top trim coincide with the specified quantity for bottom trim. The only thing that is not required here is the use of fasteners to connect to the foundation.

Return to contents

Calculation of material for racks of a frame house

In the process of installing and assembling the frame, racks play a significant role. They are constructed from timber, boards and bars. In this case, the dimensions of the block are 5*10 cm or 10*20 cm. The boards should also be different. Thin ones do not exceed 2.5 cm in cut, and thick ones - 5 cm. The width of both options should be 2 times the thickness of the board. Thus, if you use boards 3 cm thick to build a house, then its width should be at least 6 cm. The dimensions of the timber can be adjusted depending on, again, what kind of insulation you will use for the walls, floor and ceiling . Quite often, self-taught builders, in order to save money, resort to splicing several boards instead of replacing a block or even timber with them.

So, the thickness of the racks will depend on the insulation. For example, if you take insulation with a thickness of at least 15 cm, then the stand should also have a cross-sectional thickness of 15 cm. If the insulation is thinner, then a stand with a cross section of 10*10 cm is sufficient. At least important factor in the process of selecting material is how many floors will be built in the house. If this is a one-story structure, then the cross-section of the racks for the frame will be equal to 15 * 5 cm, and it is not necessary to use timber, even boards with these dimensions are sufficient. To build a two-story frame house, it is impossible to do without timber. Here you will definitely need to use a beam with a cross-section of 15*10 cm. Racks intended for placement in the corners of the structure must be even stronger and more powerful. So, for example, if you use boards measuring 15*5 cm for the main racks, then you will need to use bars with a section of 15*15 cm for the corner posts. Accordingly, when using racks made of 10*5 cm bars, you will need bars with a section of 10* 10 cm, in order to install racks on the corners of the house frame.

The length of the racks depends on such an indicator as the height of the structure. Usually standard height It is generally accepted that the location of ceilings from the floor is within 2.5 m. At the same time, in certain rooms (in the toilet, bathroom) this height can be slightly reduced (but not more than 0.5 m). Thus, when determining the length of the racks, it is necessary to take into account at what distance from the floor the ceiling will be located, to this value add the height of the floor itself (this includes flooring and floor joists), and don’t forget to also calculate the thickness facing material ceiling. Thus, you cannot simply take racks of the height that is expected indoors, otherwise the final version will turn out to be significantly lower than what you expect. Therefore, you will need to add at least another 20-30 cm to the expected height of the room.

When installing these parts, do not forget that they should be located at a certain distance from each other. In this case, it is necessary to take into account that this distance is calculated not between the outer edges of the racks, but between their axes, the center of the racks. When determining the size of the step between the racks, you need to know the exact dimensions of the OSB sheets and insulation that will be attached to the walls of the frame house. In most cases, you still have to cut out one or the other, since it is almost impossible to determine the pitch between the posts as accurately as possible. In this process, you should not forget that in those places where you plan to install doors or windows, the location of the racks should be slightly different.

Although building a house frame technology and is one of the cheapest options; its total cost can be several tens of thousands of dollars. Unlike a brick or concrete building, the construction of a frame building cannot be stretched over ten years, and most of the amount will need to be paid over two spring-autumn periods.

Therefore, before you finally choose a house project, you need to compare the estimate for this project with your financial capabilities. For an example of calculation, let's take a small 6x6 with an attic, being built in middle lane Russia.

How to calculate, what to take into account when calculating

The full cost of building a frame house includes:

price of materials, components, fasteners, equipment, and their delivery;
price of concrete and earthworks on the arrangement of the foundation;
cost of carpenters' services for the construction of the frame and rafter system, installation of stairs, partitions, laying subfloors, outer skin walls;
payment for roofers;
cost of basic finishing work— internal cladding of walls and ceilings, insulation and insulation, finishing floors, installation of windows and doors;
price for specialists installing heating systems, gas, water and electricity supply, ventilation, sewerage;
price of decorative finishing.

As you can see, self-execution of all work will significantly reduce the required cash investment. The construction process can be distributed over 3-4 years as follows:

Construction of the foundation.
Carpentry and roofing works.
Basic finishing work, installation of engineering systems.
Decorative finishing.

When calculating, it is necessary to take into account the significant level of inflation in the country(for last year from 36 to 65 rubles per dollar), because the price of building materials rises quite quickly as the ruble depreciates. It is better to carry out calculations in advance in dollars to avoid the common situation when the foundation built last year turns out to be too large and strong for the house for which there is enough money this year.

Calculation of the foundation of a frame house

In the construction of frame houses, two main types of foundations are used: — pile and tape. Pile foundations are more difficult to install, but are much easier to transport to remote areas. The longitudinal and transverse pitch of piles is usually chosen in the range of 120-150 cm, based on the size of the structure.

In places where the stove and stairs are installed, it is necessary to install an additional pile or a wider concrete base. Height strip foundation and the depth of screwing in the piles depends on the type of soil in the selected area, this can greatly affect the final cost.

IN general work foundation construction includes:

Site cleaning from the soil to a depth of 30 cm with an extension of 0.5 m beyond the perimeter. Payment for work is about $10 per cubic meter of soil. For a 6x6 house - about $150.
Laying the surface with geotextiles. 40 cents per square meter, $20 for a 6x6 foundation.
Backfilling and compacting sand with a layer of 10 cm. Price - $25 per cubic meter of sand and $10 for labor, $150 and $60 in total.

Included in price pile foundation includes:

Price of piles. 20-30 dollars for 1 piece. Total 600-900 dollars.
Installation price— $15 for 1 piece, $450 total.
The cost of a channel grillage. Depending on the thickness, the channel and its installation will cost 10-15 dollars per meter. For a 6x6 house you need at least 48 m of channel, a total of 500-750 dollars.
Price for installing a plinth. A cast concrete plinth will cost $60 for the material, and the same for labor, given its length of 24 m.

The strip foundation estimate includes:

Earthworks. With a depth of 1 m, the price for a 6x6 house will be at least $150, taking into account the foundation along the external perimeter and two transverse internal walls.
Concrete works. Concrete and reinforcement will cost approximately $100 per cubic meter, installation work will cost $50. Casting a foundation 1 m deep, 36 m long, 20 cm thick will cost $700-1050.
Waterproofing (roofing felt), embedded anchors, sewer pipes For groundwater- all together no more than $100.

In total, the foundation of a 6x6 frame structure will cost approximately:

1000$ when carrying out the work yourself, $1,700 when using a contractor - tape;
900$ and 1600$- cheap pile with caps;
$1300 and $2100- durable pile with grillage.

Particularly worth mentioning is the need for formwork for strip foundations. The material used for the formwork must subsequently be applied to the hidden parts of the frame. Cost overruns if rejected can amount to $200-300.

House box calculation

The construction of the frame of the house must be done in one season in order to prevent prolonged wetting of the wood of the frame and subfloor.

Construction is carried out in several stages:

Frame installation.
Insulation of the subfloor and laying of subfloors.
Installation of stairs.
Installation of roof and gables.
Covering the frame with waterproofing and OSB.

To calculate the cost of the frame, it is necessary to calculate the total volume of lumber and fasteners. The most common use of boards is 50x150 mm - it is used for crowns, trims, floor joists and vertical posts. The installation step of the racks and logs is 60 cm. In the longitudinal direction, logs are installed less frequently, along the crown and foundation. Let's calculate the cost for a 6x6 house:

Waterproofing the foundation with roofing felt in two layers— 24 sq.m., $10.
Board 50x150x6000 mm— 7 pcs. for the crown, 16 pcs. for the lower and upper trim, 6 pcs. for longitudinal joists, 18 pcs. on cross beams. A total of 47 boards for about $5, a total of $240.
Board 50x150x3000 mm— 44 pcs. for racks, price about $2.5 per piece. Total $110.
Board 50x100x3000 mm- 18 pcs. on the racks of two internal load-bearing walls. Will cost about $30.
3rd grade board 30x150x3000 mm— 16 pcs. for jibs, $15.
Beam 100x150x6000 mm— 2 pcs. for Mauerlat, $20.

For the formation of window and doorways scraps of 50x150 mm boards left over from cutting the rafters to size should be used (see below).

Underfloor insulation produced at will, it consists of filling the subfloor with expanded clay to the level of the logs. With a thickness of expanded clay of 30 cm, to insulate a 6x6 house you will need 10 cubic meters of expanded clay, which will cost $300.

Subfloor The log is assembled in each cage using a 25x100 mm board over a 40x40 mm cranial block. Material consumption per cell is 60x150 cm, taking into account the thickness of the logs - 4 m of timber and 7.5 m of board. Total for two floors 6x6 - 320 m of timber and 600 m of board. When using grade 3 wood, the costs will be $40 and $120 for timber and boards, respectively.

Cost of stairs can really hit the budget of a demanding builder. Buying a carved factory staircase will cost $250 per meter or more. Manufacturing from purchased decorative materials It will come out 2-3 times cheaper, and from ordinary lumber with your own hands - about $25 per meter. The length of a two-flight staircase at an angle of 45 degrees will be about 5 m, a single-flight staircase - 4 m.

Attic and roof

The gables are assembled like walls, and are installed at the ends of the roof. For two gables of a 6x6 house, equipped with a gable roof with a slope angle of 30 degrees, raised one meter above the ceiling to form an attic, you will need about 90 meters of 50x150 mm boards, for a total price of $75.
The ridge beam is attached to the tops of the gables. If the length is more than 6 m, it must be supported by at least one supporting wall or support from a load-bearing beam. For the ridge, a double board with a cross section of 50x200 mm or more is used, for load-bearing beams - laminated veneer lumber. The price of a ridge for a 6x6 house is $15, with a supporting beam made of laminated veneer lumber 80x190 mm in the center — $55.
The rafters are laid on the mauerlat and ridge in increments of 60 cm. A total of 22 are needed for 6x6 roof rafters rafter legs 4.5 meters long, made of 2nd grade board 50x150 mm. Total cost: $80. Considering that the material is sold by 6 m, the real cost will be $100.
The roof is covered with wind and waterproofing. The price is about $40 per roll of 75 sq.m.
Transverse lathing made of 50x50 timber in increments of 0.5 m will cost for gable roof with an area of 48 sq.m. for $25 (96 meters of timber).
Costs for roofing material and additional parts depending on the selected material and roof intricacies can range from $6 to $12 per square meter. For example, the most simple roof without valleys, area 48 sq.m. The total cost will be $300.

External cladding -produced in two layers. First, the walls are sheathed with wind-waterproofing, then the structure is sheathed with OSB. The entire outer surface of the frame, including the gables, as well as load-bearing walls on the side less exposed to moisture. The entire film is installed with an overlap of 10 cm. For a 6x6 house with a total area of external walls and gables of 96 sq.m and an area of internal load-bearing walls of 30 sq.m, the costs will be:

2 rolls of waterproofing for $40, total $80;
40 sheets of OSB 9x2500x1250 mm approximately, taking into account window and door openings, $12 per sheet, total $480.

There are two types of frame house partitions — load-bearing or non-load-bearing. The load-bearing ones are installed with racks on the crown, made of materials of large cross-section, using jibs and OSB for strength. Non-load-bearing ones can be made from 50x50 mm timber, covered with plywood or plasterboard. Their installation is possible at the stage of finishing work, on the surface of finished floors.

Price of fasteners(screws, corners, nails) to assemble a building box is 4-5 dollars per square meter of area, for a 6x6 building - 150-200 dollars.

Interim calculation of the cost of a house box

In total, a 6x6 house box protected from wind and rain will cost:

450$ - frame;
600$ - underground floor, subfloor and stairs;
600$ - roof and gables;
600$ - sheathing.

Most construction companies offer services for 30% of the price of materials, the total cost will be about $3,000. Having sewed up the openings with polyethylene, if necessary, such a structure can be left until the next construction season.

Windows and doors

The cost of windows including installation ranges from $50-100 per square meter, outer door— 100-300 dollars, interior doors- 50-100 dollars. For a frame house, it is undesirable to use windows wider than 120 cm, so as not to reduce the pitch of the racks by more than 2 times.

If for a 6x6 house we assume the presence of eight windows 120x120 cm (2 windows on each wall, except for the corner with the bathroom and shower, and one window on the pediment) and five internal doors, the total cost will be at least $1000.

Insulation

Installing insulation is not very difficult; it is cheaper to do it yourself. Sheets of insulation are laid in the space between joists, posts, rafters and covered with a vapor barrier. The subfloor must be additionally covered with waterproofing before insulation.

Required layer of thermal insulation:

For external walls and roofs- 15 cm or more.
For load-bearing internal walls, floors and soundproofed partitions- 10-15 cm.
For partitions- 5 cm or no insulation at all.

Most cheap material — glass wool, priced at $20 per cubic meter. But it is recommended to use more expensive basalt wool for $30 in frame houses, which has higher durability and environmental friendliness.

For a 6x6 house you will need for insulation:

1 roll of waterproofing — 40$;
4 rolls of vapor barrier — 80$;
21 cubic meters of mineral wool 15 cm thick — 630$;
7 cubic meters of mineral wool 10 cm thick — 210$.

In total, insulation will cost at least $950, or about $1,200 if you hire a contractor.

Installation of finished floors

Finished floors are laid along the rafters with boards 25x100-150 mm. If there are no plans to install a special flooring you can take a tongue and groove board. The price per square meter of flooring is $6 for a tongue and groove board, $4 for an edged board. Carrying out the work yourself will save you up to 50% of money. Two finished 6x6 tongue and groove floors will cost $450.

Cost of communications and heating

Costs for water supply and sewerage significantly depend on the distance from the water source and drain. Assuming that these points are in close proximity, the cost of the system is from polypropylene pipes, shower, bath, toilet, several sinks and taps, boiler will be at least $500, and $300 for the services of a specialist.
Heating installation costs largely depend on the availability of the gas network and can exceed the price of the entire house. The cheapest installation is electric heating— $6 per 1 sq.m of heated area, but electricity costs will be huge. Water system Heating from a gas boiler for a 6x6 house will cost $1,300, as well as $1,000 for the services of specialists for installation and commissioning of equipment. The work of a good stove maker will cost 5-7 thousand dollars.
When calculating installation costs power supply systems construction companies take into account the area of the house. An electrical system sufficient for normal living will cost 5-10 dollars per square meter of living space. Installing an electrical network in a 6x6 house will require costs of $250 for materials and $150 for specialist services.

Interior and exterior finishing

For interior decoration Frame houses are most often covered with clapboard or plasterboard. The average price for plasterboard is 3-5 times less than for lining, and is $4 per sheet with an area of 3 sq.m. It is better to sheathe some rooms with waterproof plywood (kitchen, toilet, shower).

For a 6x6 house you will approximately need:

lining for finishing the attic - 80 sq.m., $400;
plasterboard for finishing residential premises - 63 sq.m., $90;
waterproof decorative plywood for finishing office premises - 63 sq.m., $200;
floor and ceiling skirting boards – 96 linear meters, 400$.

The total cost, including hired labor, will be $1600.

For exterior finishing They use various types of siding, eurolining, block house or imitation timber. Various types materials can cost from 2 to 15 dollars per square meter. Quite presentable finishes can be found at prices starting from $5. Finishing a 6x6 house with Class A aspen clapboard will cost $500, and $400 in workers' compensation.

Additional finishing depends only on the imagination and budget of the owner, and is not included in the construction estimate.

Houses made of SIP panels

The technology for the rapid construction of houses from SIP panels, developed in Canada, allows you to speed up the assembly of the house and eliminate the need for insulation and waterproofing. The SIP panel consists of 2 OSB-3 boards, firmly glued to a sheet of especially durable polystyrene foam, standard size 1250x2500 or 1250x2800 mm.

The panels are fastened together by double inserts made of 40x200 mm timber, which make up the building's load-bearing frame - floor joists, vertical posts. SIP panels are applicable as ceilings, walls, gables, rafters and continuous sheathing.

The cost of installing one slab will be:

40-70 dollars - panel;
$10 – fasteners and lumber;
$20 - work.

The total cost of constructing a 6x6 house frame from SIP panels:

$600 - roofing;
$300 – insulation of the subfloor;
$2000 - two floors;
$3300 - internal, external load-bearing walls and gables;
$1200 - rafter system.

Total including work $7400, with self-installation — 5700$. The initial investment will allow you to save on insulation and finished flooring in the future; in addition, according to manufacturers, houses made from SIP panels are much stronger than conventional frame panels.

TOTAL

As a conclusion, let’s summarize the cost of a 6x6 frame house for different options construction: Rating: 4.7 6 votes