The engine from the vacuum cleaner where you can adapt. Vacuum cleaner engine: where can it be used in everyday life? but on the other hand

How to make a vacuum cleaner? A homemade unit assumes the presence of an engine at 6000 rpm. Such a part can be removed from the juicer. Please note that not all electrical appliance motors are rated for long service. Therefore, when choosing an engine, follow the rule: the motor must withstand a large load and have protection against overheating.

What to do if you can’t find anything other than a part from a juicer?

In this case, it is advised to equip it with a thermal fuse rated at 126 ºС. The cross section of copper must correspond to the dissipation power, so this temperature may not be suitable for the motor you have chosen. It should be noted that the border of 130 ºС is the average for which most transformers are designed.

What can be taken as the basis of a homemade unit?

Many are interested in how to make a vacuum cleaner with your own hands.

You can take as a basis:

An exhaust motor with an Axial model will not work, as it is used in models of a cheap segment and does not have the necessary power.
Disused vacuum cleaner engine.
Engine washing machine.
Refrigeration compressor motor.

Refrigerator engine application

How to make a vacuum cleaner from It will be difficult to pick up a part, since the rotation speed of the shaft is different models refrigerators are different. If you are assembling a vacuum cleaner, then a strict 6000 revolutions will be required. Compressors of the old rocker type are designed for 3000 rpm.

Crank modifications have half the speed, and linear inverter units are not at all suitable for assembly.

Inside reciprocating compressor cost of an electric motor. If you cut the case and remove the motor, then it is suitable for any purpose. It has high power and quiet operation.

Asynchronous motors are rarely used. For example, a collector configuration operates from the outlet if speed control is not required.

Using a washing machine motor

The design of washing machines suggests the presence commutator motor. The speed of its operation is regulated by a thyristor key. If the motor is powered directly from the outlet, then the speed will become high, but they will not reach the figure of 6000 in the absence of a belt gearbox. In this case, the spin function is quite achievable.

How to make the unit suck dust?

Commercials often talk about the vacuum created in the vacuum cleaner. The engine allegedly contributes to the discharge, into which the drawn-in air stream rushes. But is it really so? Rather not, because at negative pressure, a bypass valve is connected to ensure balance. But that is not the essence of the work. To suck dust, a hermetically sealed housing is used, thanks to which the flow of nitrogen and oxygen molecules rushes in the right direction. The container in this case does not play any role.

If you stick to the factory configuration, then you need a bucket made of steel or plastic, the bottom of which has an air intake hole. The motor is mounted on the axis, and something similar to a squirrel cage is installed on the shaft. The air flow is captured by the blades and thrown out to the perimeter. This provides traction. A hose is hermetically attached to the bottom. We will assume that the assembly of the vacuum cleaner with our own hands is completed.

How does a mini vacuum cleaner work?

How to make a mini vacuum cleaner? The speed control of the unit is carried out according to the thyristor circuit. Any electronic part from an old vacuum cleaner, washing machine or food processor will come in handy.

The main thing is the cutting method, not the engine power. But the key also overheats. It is easy to understand whether it corresponds if you compare the power of the device from which the circuit was taken with the power of the engine. If the thyristor indicator is low, then it is advised to attach a radiator to it, and forced cooling is already available.

How to make a container for a homemade vacuum cleaner?

The vacuum cleaner is designed in such a way that it will not work without a container.

For homemade unit fit:

ordinary bag;
a container filled with water;
cyclone chamber.

Filtering the bag is problematic. If you will be vacuuming crumbs from the table, this design is fine. The type of container is selected according to the type of waste. For example, dust collection is best done through a filter with water or a cyclone chamber. Both types of container are easy to construct. The unit itself is stationary. If a gardener uses such a device, then it can be hoisted onto a cart and moved around the garden.

The cost of stationary models of vacuum cleaners is high, so homemade construction will be most welcome.

The simplest container model is a large tank filled with water. It plays the role of a water filter. In this case, the dust will sink. The inlet of the hose is made taking into account that the flow collides with a water barrier. An ordinary flat-bottomed box is two-thirds filled with water. In addition, a baffle hangs from the ceiling above the filter surface. All the dust settles in the water and sinks. Such a device requires periodic cleaning. Such a design will not be suitable for gardening, as the weight of the water is large. Therefore, it is replaced with air.

When assembling vacuum cleaners for the garden with your own hands, adhere to the following rules:

Air enters tangentially into the tall barrel.
Along the axis of the tank, up to about two-thirds of the height, there is a pipe that provides an exit.
Garbage sits on the bottom due to the fact that it is carried to the periphery by centrifugal force.
The airflow exits in the center.
The smallest particles get into the engine in any case. Therefore, it is recommended to equip the container with a HEPA filter at the outlet. It's not worth saving. Otherwise, you will have to constantly lubricate the engine. If the vacuum cleaner sucks in water, it will end up in a barrel.

Such homemade vacuum cleaner great for a gardener. The unit can be made universal. For example, cut the barrel to fit the diameter of the tank with standard sizes and equip the device with a van for movement. So you can clean up the whole park.

How to make a mini vacuum cleaner from a plastic bottle?

Today, almost every home has a computer. As you know, its body is periodically clogged with dust, which prevents the cooling of many parts. The circuits should be vacuumed from time to time. To facilitate the process, you can use a homemade mini-vacuum cleaner.

For the manufacture of the unit you need:

fan from the computer;
plastic bottle;
hose;
polystyrene;
power supply 220 V/14 V;
insulating tape;
paralon.

Progress

A plastic bottle is cut in half. The part that remains with the cork is taken. A filter is cut out of the foam rubber. It is inserted into the neck. The material must be tight.
A hole is threaded through the cork into which the hose is inserted.
The cork is screwed onto the bottle.
A fan is taken from the computer (its corners are smoothed). It is inserted into the bottle in such a way that during operation the air flow rushes to the wide side of the bottle.
The place where the cooler is located is wrapped with insulating tape. A wire is used for strong fixation.
The power supply is connected to the fan. The red wire goes to the positive side, and the black wire goes to the negative side.

How to make an industrial vacuum cleaner with your own hands?

How to make an appointment? The basis of one of these units is the Ural PN-600 model.

You will need:

Bulgarian;
a pipe with a diameter of 4 cm and a length of 20 cm;
plastic bucket with handle and lid;
scotch;
insulating tape;
drill;
self-tapping screws;
glue;
medical bandage.

Stages of work

First of all, the Ural garbage collector should be finalized. For this purpose, the wheels are unscrewed from the bottom with a screwdriver. Holes are sealed with tape.
Then you need a grinder, with which the latches and bartacks are removed. A plug is installed, rewound with insulating tape.
A hole with a diameter of 43 mm is drilled in the bottom.
Gaskets are cut out of the seal, the thickness of which is 4 mm.
A gasket, a bucket lid and a centering pipe are placed in the waste container.
Using a drill, a hole with a diameter of 2 mm is made.
The cover is fixed with self-tapping screws 4.2x10 mm.
An external hole is made for the suction pipe. It is planned at an angle of 15º. The hole is cut with scissors for metal.
The pipe is fixed with self-tapping screws. For sealing, they use an ordinary medical bandage, which is impregnated with Titanium glue. The bandage is wound around the nozzle.

Second way

To assemble the unit in the second way, you will need:

old home vacuum cleaner;
oil based filter;
bucket with a capacity of 20 liters with a tight-fitting lid;
PP corners 90º and 45º with a diameter of 40 mm;
meter of plastic pipe with a diameter of 45 mm (a corrugated pipe with a length of 2 m and a diameter of 40 mm is suitable).

Device assembly

First, take the lid of the bucket. A hole is cut in it at an angle of 90º. Then a corner of the same size is inserted.
When a corner is inserted into the lid, all the cracks are covered with glue using a construction gun.
A slot is made in the side of the bucket, into which a 45º corner is inserted. All cracks are also covered with glue.
To connect the corrugation to the corner, it is necessary to cut off a piece of pipe with a diameter of 40 mm. The corrugation should fit snugly. If it does not fit on the inlet pipe, then you can resort to using a siphon model on the kitchen sink.
The narrow end of the corrugation is fitted to a forty-millimeter pipe. The other end is connected to the opening of the vacuum cleaner.
To prolong the life of the filter, a nylon stocking should be pulled over it.

Can an old vacuum cleaner come in handy?

There is an old vacuum cleaner at home. What can be done from an unnecessary unit?

If the device works, then it can be used for another purpose. Some methods require technical training, since reworking equipment is dangerous. In particular, you should understand the principle of operation of motors.

This article will describe the safest methods.

Air blower

If you connect a hose to the outlet available in most models, you can get a unit for inflating rubber mattresses, pools for children and other similar things. The vacuum cleaner container needs pre-treatment from leftover debris.

What can a Typhoon vacuum cleaner do?

What to do with an old Typhoon vacuum cleaner? The principle of operation of the unit is different high level performance.

The case of a Soviet-made vacuum cleaner is impossible better fit to create a device for grinding grass. It has a top opening of a suitable diameter. "Typhoon" is an excellent option, but not the only one.

What else can be applied?

The body of the device can be replaced by a container in the form of a cylinder. For example, a pan, a bucket, or a piece of pipe is used.
The 180 watt motor is taken from an old washing machine.
Used as knives hacksaw blade. You will need a profile for the rack rectangular shape size 15x15 mm.
The sleeve for attaching knives is machined on lathe. Its height is 40 mm.
The engine with the pulley removed is attached to the container from below by means of studs.
To clamp the knives, water nuts with a diameter of 32 mm are used.
A hole is cut for the motor shaft.
For secure fixation a pair of holes with a diameter of 7 mm and an M8 thread for locking bolts is made on the shaft in the sleeve.
Platforms are machined on the reverse side of the motor shaft to increase the level of reliability of fastening the bushing with locking bolts.

Grain crusher manufacturing

To make a grain crusher, a person must have experience with machinery. Self-manufacturing devices without relevant knowledge is not recommended.

Take a sheet of plywood square shape. An electric motor is fixed on it so that the shaft goes down by 40 mm.
The steel plate is mounted on a threaded tail. It is fixed with nuts, bushings and washers.
Leading edges are sharpened on both sides of the axle.
The axial hole is made in the middle of the plate.
To create a working chamber for the future unit, a body is made in the form of a ring. Its basis is Correct design details involves bending the edges of the rings outward. They should form 10 mm flanges. It is with their help that the body is attached to the base. A sieve is screwed to them.

Making an attraction for children

What can be done from an old vacuum cleaner for children? If the motor of the unit is running, then it can be used for the attraction.

For this purpose, a tennis ball is pierced through with a pin, so that the ends of the pin are on both sides of the ball.

After that, the propeller is made. A jar made of polystyrene is used. The propeller is mounted on top of the ball. One lane is enough for him. It is cut with scissors.

The propeller is pierced in the middle and mounted on the axis of the pin. For speed and ease of rotation, it is advised to make bearings from beads. They are attached on both sides of the strip.

The top edge of the pin is bent in such a way that there is not much play on the axis.

Such a ball can be launched into the air through the outlet. If desired, the ball is decorated with sparkles.

Conclusion

This article described how to make a vacuum cleaner. There are many build options. It was also described what can be done from a vacuum cleaner.

Remember that without the appropriate technical knowledge, it is not worth getting down to business. It will be difficult to make a vacuum cleaner yourself in this case. It is better to seek help from a specialist.

Household appliances break down and wear out over time. A vacuum cleaner is a classic household cleaning tool. Often, when this unit breaks down or wears out, people buy a new one without thinking about what can be done from the heart of the dust collector - the engine.

Today there are many various models vacuum cleaner. However, all devices are made according to the same principle. The engine of the unit during operation is gaining power, which rotates the impeller.

Disassembly

An engine for building the necessary household appliances. But before creating a new item, you need to get and disassemble the heart of the dust collector.

Sometimes during disassembly, it becomes difficult to remove the nut that holds all the parts of the unit together. Nut holder firmly sits in the middle of the motor with a sealant.

Samsung dust collector motor - 11ME83

Attention! It is impossible to scroll the rotor of electric motors with metal devices like a screwdriver, trying to remove the nut. The nut will come off and the winding will be damaged. It is unlikely that it will be possible to restore the stroke with your own hands.

List of required materials

For disassembly you will need:

pliers;
screwdrivers;
wrench for unscrewing the nut with a diameter of 1.2 cm;
vise;
2 wooden bars 10x40 mm;
round file;
a hacksaw designed for metal surfaces.

The dust collector motor is always assembled in the same way. The difference lies in the volume and mass of parts. Tools must match their size.

Procedure

Preparation of the tool and the unit itself is required. First, the brush is unscrewed from the back surface, then the casing is removed, the role of which in the engine is to cover the impeller from the front side.

Broken motor impeller

Often the casing is firmly attached to the body. In this case, pliers are used: the edges are bent on the sides and the casing is wrung out with a screwdriver.

The procedure for unscrewing the nut:

The rotor is carefully locked by tightly clamping it through the recesses that are designed for the brushes. This will require bars, the size of which is indicated above. wooden bars inserted into the recesses for the brushes. The whole structure is tightly pressed against the anchor with a vice. If the bars do not fit into the brush holes, they can be filed with a round file.
The nut is unscrewed using a wrench. The wrench nozzle is selected according to the size of the nut.
Removal of the rest of the structure. Suitable screwdrivers are taken from the tool kit to unscrew the remaining parts on the engine.

They disassemble the motor in order to determine a breakdown or upgrade to create other useful household items.

Creation

What can be useful to do from the engine of the vacuum cleaner? The following are products that are designed using a dust collector motor.

lawn mower

For people who are thinking about where to introduce the engine from a vacuum cleaner, it is proposed to design their own lawn mower.

This household item is constructed using the heart of a vacuum cleaner in working order. Usually dust collectors wear out and are thrown into the trash. Instead, the engine of the unit can be used to build a lawn mower: sufficient power is 500 watts.

Homemade lawn mower made using a vacuum cleaner engine

Materials required for assembly:

apparatus for welding;
Sheet steel;
unnecessary baby stroller;
old saw or hacksaw.

To begin with, the wheels of the stroller are separated. It is better if the wheels are large, as this will ensure the patency of the product on uneven and rough soil. Excess parts are cut off, but you can leave the handles, as it will be convenient to hold the lawn mower while moving.

Next, a platform is constructed, on which the engine with the dust collector shaft is then placed. It is necessary to follow the rules under which the platform with the shaft will be facing the bottom. To protect such a motor and shaft from possible damage, you need to cut a casing about 1.2 cm thick. A hole is cut in the casing. The size of the hole should be 0.5 cm larger than the motor placed on the platform. Before installation, the distance from the motor to the floor is measured. The size of the distance is not less than 3 cm.

The next step is cutting the steel disc. Diameter - 35-45 cm. The volume of the disc is compared with the force applied to unwind. A disc 45 cm or larger requires a powerful motor. In building a lawn mower, it is better to use a disc bigger size because the power of this vacuum cleaner motor never fails. A hole is drilled in the central part of the cut disk. The tip of the shaft passes through it along with the engine.

2 cm are measured from the sides of the disk, then 2 holes for the knives are drilled at the indicated distance.

The old saw is deformed and turned into 2 knives. Before inserting into the above holes, the knives are sharpened. Recommended length - 5.5 cm, width - 3 cm. Using M6 bolts, the cut parts are fixed on the disk. Blades every 3 lawn mowing.

Read the article - using a vacuum cleaner.

Trimmer

A trimmer is a device that performs the functions of a lawn mower for hard-to-reach places.

Grass trimmer

For Assembly garden tool will need:

extrusion;
dust collector motor;
homemade knives;
disk made of plastic or steel.

The engine is fixed at the foot of the bar. Knives cut from a hacksaw of the same size as in the above section are attached to the shaft. Another option is to attach a disc to the shaft and make a hole in it for threading the fishing line. From above, for protection, the device is covered and secured with a casing.

Alternatively, you can use a plastic casing. It can be built from sewer pipe, which is usually used when installing a mixer.

To cool a high-power engine, the following device is made: a disc with concave blades is inserted under the place where the fishing line is threaded. This part serves as a fan.

Fan

From the motor of the old dust collector comes out an excellent fan for cleaning rooms. What you need for construction:

compacted rubber bands;
turbine motor;
half of the body from the vacuum cleaner.

Wires are brought out to the body and the motor is fixed. Then rubber bands and a casing are put on to protect against damage. Air is drawn in from one end and exited from the other.

Finished blower design

A plastic cone is attached to the place where the air mass exits, the end of which is cut off.

Next, a plastic tube is attached to the body, which will serve as a handle for holding. You need to bend the tube carefully so as not to break it, therefore better place heat up the fold for a few minutes with a hair dryer.

Turbine vacuum cleaners have a lot of power, so there is strong air ventilation. Apply built fan. The main advantage is that there are no costs.

We have dedicated this article to technology news. Sometimes even old things can be used. For example, you can make something useful for your home from an old vacuum cleaner. In the article, we will consider several ways to give a second life to a vacuum cleaner, but in a different capacity.

What can be made from a vacuum cleaner and is it worth it at all?

So what can you do with an old vacuum cleaner? If you have purchased a new home helper model and data-lazy-type="image" data-src="http://chistyjdom.ru/wp-content/uploads/2018/09/920-900x681-300x252.jpg" alt ="123" width="187" height="157"> If you don’t want to throw it away, you can always use it in everyday life. And then the device will serve you faithfully for more than a dozen years.

The most basic part for most technical devices is a motor from a home assistant. The main thing is that it is intact and works properly.

A few ideas:

fan
spray gun
grain crusher
trimmer, etc.

Materials and Required Skills

Special skills for the manufacture of the fan is not required. And handy tools are enough. And also the majority necessary materials found in a garage or pantry..jpg" alt="123" width="146" height="128">

motor engine
plastic tube
network cable

And for a homemade spray gun, you only need a spray gun and some technical skills. Skills will help you understand the principle of operation of the vacuum cleaner and understand how to switch it to blowing in the opposite direction. The same principle will be needed for the invention of the blower.

Now, if you want to save money on some appliances, then you can do a lot with your own hands and not spend extra money.

Fan? Easily

With the help of a powerful motor from an old vacuum cleaner, you can easily invent a fan to clean some surfaces, as well as get a blower.

We take out the motor engine from the old vacuum cleaner. To it must be attached network cables to plug into an outlet. We attach a plastic tube to the motor and bend it a little. For more elasticity of the tube, it can be heated with a hair dryer. This homemade handle will allow you to comfortably hold the blower in your hand.

Airbrush? And the painting will speed up at times

piece of steel
hacksaw for metal
old carriage
welding machine

An old baby stroller is needed for the structure that will move the main part of the body. It will be better if you have large wheels and a comfortable handle, the rest can simply be cut off and thrown away. A motor with a shaft is installed on top of the resulting platform. For the construction, a casing for protection should be cut, the thickness of which is at least 1.2 cm.

A hacksaw for metal needs to be deformed a little to make knives out of it. With the help of a nut and bolt, the knives are installed in a pre-cut disk.

A trimmer is a device necessary in hard-to-reach places..jpg" alt="123" width="157" height="189">

long stick
engine motor
steel plastic

We attach the engine to the end of the stick, which we fasten to the steel plate. Homemade knives are installed on the plate. Knives must be made from old saw or scissors.

Other useful life hacks

Consider a few interesting ideas where you can fit the vacuum cleaner motor:

Data-lazy-type="image" data-src="http://chistyjdom.ru/wp-content/uploads/2018/09/584e8d3309b92-295x300.jpg" alt="123" width="159" height= "162">

And finally

If your old vacuum cleaner breaks down, you can always find a replacement for it. But you should not rush to get started, check its performance. Often the breakdowns are minor:

network cable damage
power circuit damage
pipe damage
clogging of filters and dust collectors, etc.

But if, nevertheless, something prompted you to some homemade products, then we hope that our article will help you in choosing a new convenient and good assistant for your home, garage, on construction site and even in the yard.

Quite often a situation arises when a new vacuum cleaner is bought into the house. modern design, and the old, quite working "hard worker" remains out of work. As a result, the old vacuum cleaner gathers dust in the far corner of the pantry according to the principle “it’s a pity to throw it away and takes up space in vain.” However, in many cases, such a technique can find a second life in a completely different capacity. Consider several options for using an old vacuum cleaner as a home assistant.

Despite the wide variety of models of vacuum cleaners, they all work on the same principle. A sufficiently powerful and high-speed engine drives the impeller, which blows a large amount of air through itself. As a result, a vacuum is created at the inlet of the vacuum cleaner to suck debris into the receiver, and at the outlet - an air jet cleaned from dust by filters. These properties can be successfully used for different purposes.

Air blower

If you connect the hose of a vacuum cleaner to the outlet, which is on many models, then we get a very convenient powerful source of air for pumping rubber mattresses, children's pools and other similar things. Of course, you must first thoroughly clean the receiving container of the vacuum cleaner from the remnants of debris and dust that have accumulated there over the previous time. In this way, we can avoid getting dust and dirt into the inside of the item that we are inflating.

If you have a small household plot, then an old vacuum cleaner can be used to clean the surface of the tracks from dust and small debris by blowing. For these purposes, a nozzle with a narrow hole is mounted on the end of the hose connected “for blowing”. According to the laws of physics, the air jet, leaving such a nozzle, acquires high speed and effectively blows off dust, sand and other small objects.

Another place to use the "old man" can be a home workshop. In this case, depending on the desire of the owner, you can use both the "input" and the "exit" (for example, collect wood dust from a jigsaw, blow dust off the surfaces of objects prepared for painting, etc.).

Fun attraction for kids

Despite the abundance of modern toys, children will be happy to take part in the fun called "flying ball". For these purposes, we need the following things:

Vacuum cleaner with a hose connected "for blowing";
Several table tennis balls;
Thin pins;
Washed polystyrene jars (for example, from children's cheese such as "Theme", "Agusha" or the like);
Small round beads with a hole (you can borrow from your mother or grandmother).

We begin the manufacture of a “flying ball” by carefully piercing the wall of the ball from two opposite sides so that it is, as it were, “imposed” on a pin. Then we start cutting out the propeller, which will be fixed on top of the ball. In this case, it will be convenient to use stationery scissors, with which we carefully cut a strip about 5-7 cm long and about 1 cm wide from a polystyrene jar. It is better to cut this strip with some margin so that you can adjust the propeller later.

We pierce the propeller exactly in the middle and put it on the axis of the pin. To make the propeller rotate easily, we put beads on top and bottom of the polystyrene strip, which will act as bearings. We bend the upper tip of the pin in such a way that the propeller rotates easily and at the same time does not have too much play on the axis.

"Flying ball" is almost ready. Now it remains for us to turn on the vacuum cleaner and adjust the air supply from it so that the propeller of the ball rotates under the action of a jet directed from below, and the ball itself floats in the air. If it doesn't work the first time, no problem. Gently bend the polystyrene blades over the lit gas burner so that when they rotate they create a lifting force.

Properly adjusted " balloon» floats freely in the air stream that comes out of the vacuum cleaner. In this case, you can make it maneuver in the air following the smooth movement of the hose. In order to make the ball look elegant, it can be painted, for example, in the form of a cheerful character Carlson, who lives on the roof.

What useful things can be done from a vacuum cleaner motor

When buying a new vacuum cleaner, the old unit is most often thrown away. But if an older vacuum cleaner is still working and quite serviceable, it can get a second life. Some methods require technical education, since it is dangerous to redo equipment, and especially motors and unknowing people are better off not risking their health and entrusting such work to professionals. The safest and simple ways what can be made from a motor from a vacuum cleaner or itself will be presented in this article.

Grain crusher
Car
Attraction
Air blower

To make a grain crusher from a motor from a vacuum cleaner, you need to have some skills.

What can be done from a vacuum cleaner engine?

People who do not understand the data structure and similar devices should not independently convert the motor into a grain crusher.

First you need to take the base from a square sheet of plywood and fix the electric motor so that the shaft drops down by forty millimeters. The steel plate must be installed on the threaded tail, and the plate is fixed with nuts, bushings and washers. On both sides of the axis, the leading edges must be sharpened, and the axial hole itself must be made exactly in the middle of the plate.

To make a working chamber for a future grain crusher, you need to make an annular body of metal strips. For everything to be correct, you need to bend the edges of the ring outward so that they form flanges of ten millimeters. It is with the help of these flanges that you can attach the body to the base and fix the sieve to them.

Car

Since car owners treat their vehicles very carefully and reverently, cleaning should be of high quality and fast. No matter how much money you spend on another vacuum cleaner for your car, you can simply use an old home vacuum cleaner. If the motor of the vacuum cleaner is fully operational, it can easily cope with dust, crumbs and dirt in the car. It can be used to clean seats and carpets.

Since men love to spend their time in the garage fixing the car or something else, the place is often dusty and dirty. In the garage, a vacuum cleaner is useful for cleaning sawdust, dust, sand and other things. An old vacuum cleaner with a working motor will become indispensable assistant for cleaning both the garage and the car.

Attraction

If the motor in the old vacuum cleaner is still quite working, you can use it as an attraction for children. To do this, you need to pierce the tennis ball with a pin so that the pin is on both sides. After that, you need to make a propeller from a polystyrene jar, which will be fixed on top of the ball. For the propeller, one strip cut with ordinary stationery scissors will be enough.

The propeller needs to be pierced in the middle and put pins on the axis. In order for it to rotate easier and faster, you need to make bearings from beads that need to be attached to both sides of the propeller strip.

Also, you need to bend the top edge of the pin in such a way that it does not have too much play on the axis. Such a "flying ball" can be launched into the air using the air blowing function. Over time, you can learn to give maneuverability to the ball with the help of air flow. If desired, the ball can be decorated with sparkles or decorated with any color.

Air blower

If the motor is still running in the old vacuum cleaner, then it is quite fit for work. In addition to its direct duties, the vacuum cleaner can be used as an air blower. It is perfect for inflating children's pools, balls and mattresses.

In addition, an old vacuum cleaner with a working motor can be taken to the country house and used there. It is perfect for cleaning leaves with the help of reverse air supply, that is, by simply blowing them in the direction of your choice.

http://whatican.ru

█ Vacuum cleaner how to unscrew the nut. Vacuum cleaner engine repair (how to disassemble the engine) fixtures.

In this video I will tell you how easy it is to unscrew the nut on the vacuum cleaner motor without any planks and other special tools. The cost of a subscription to our club is 300 rubles. The essence of the project is to create a group for training in the repair of the main types of electronic and digital equipment with the further opening of its own OWN BUSINESS. At the same time, the construction of the course will affect not only novice masters, but also represent the interests of the ALL audience: from the layman (who does not know how to hold a soldering iron) to experienced craftsmen who already want to go higher and become a LEADER, start their OWN business! We have assembled a worthy team to be able to give IN-DEPTH knowledge on the repair of: Portable digital equipment and mobile devices Laptops, computers, office equipment Household and audio appliances LCD TVs, monitors. The construction of the material is simple and as detailed as possible: from A to Z. WITH REAL everyday malfunctions, typical problems and sometimes NON-STANDARD solutions! The project is constantly

How to unscrew the nut on the vacuum cleaner motor. super way! motor repair. The easiest way to disassemble the Samsung vacuum cleaner motor. ;). My fourth homemade grinder. My channel shows how it works. The engine used from the "washer" 2800 rpm. min, 120 watts. power. We calculate the belt speed according to the formulas: Roller circumference L=2PR=DP(R-radius, D-diameter, P-3, 14) Engine revolutions per second. F=2800 60=46, 66 Belt speed S=L*F. Upper roller: width 50mm, diameter 50mm in the center, to the edges it decreases to 48mm (barrel-shaped for adjusting the tape) from the ends of the groove for bearings. Bearings 180201 (international designation 6201 2RS) dimensions: inner diameter 12mm, outer diameter 32mm, width 10mm.

Homemade grinder No. 4 "mini grinder" How to replace the risers in the apartment, a list of materials, and the price of the issue. REPLACEMENT OF THE SEWER STICK OF COLD AND HOT WATER. ___________________________________________________________ LINK to our CHANNEL: — — — Repair of the APARTMENT P. 1 Exclusive 2017 All Step by step — DISMANTLING WORKS P. 2 MAIN DUSTY STAGES Repair of the apartment. Riser replacement cold water. Riser replacement hot water. Sewer line replacement. Sewerage. Replacing Clay Main Sewer Line With ABS Plastic Pipe. Basics of Your Home's Plumbing. Stages of replacing the riser in the apartment. Replacement of cast iron sewer. Replacing the cast iron riser in the apartment. Replacement of the common riser. Cast-iron sewage. water in the house. water pipes.

█ replacement of the sewer riser h.-3 / cold and hot water / sewerage. Repair of the starter anchor: Polishing the lamellas (ALPHA, DELTA, SABUR 139FMB) Foam filter ●LED stop signal - If you like the video, you can support the channel by donating any amount you wish. MasterCard — 5168 7553 2759 3097(PrivatBank) QIWI — +380937373045 Yandex — 410012753834964 Webmoney — Z393128700795 EasyPay — 27467405 ●My Blog – ●My affiliate program! - Connect AIR ●VK group - ●Music - from the free YouTube library ●My wast: Gilera DNA 50 ●I shoot on - Panasonic HC-V110 Black Action camera SJ4000.

Brush Killer Video Sponsor Auto Parts MILES: Auto Repair Channel: Dimexide to Engine Step Drill AutoScanner My 2nd channel. Before unscrewing, ALWAYS check which thread (in which direction to unscrew) My affiliate program on You Tube.

1 how to disassemble the engine from a vacuum cleaner \ how to unscrew the nut \ how to change the vacuum cleaner bearings How to align the corners in an apartment without beacon plaster. Ennoble the holes of the exhaust shaft and what to do with the protruding metal on the walls. Thank you all for your support of the channel. ______________________________________ Link to CHANNEL: Plastering corners, how to putty corners, how to make an even corner, a corner under building rule, align the corners with the rule, how to remove rust from the walls.

█ how to align the corners of the walls in the apartment / shaft hole / rust on the walls. The pump began to work loudly and get very hot, the reason is the wear of the bearings. With further operation, the motor will jam and the winding will burn out.

When the engine is warm \when it's time to chaMy instagram: The Jet Plane Project is finished! The video on the channel will now be released without a clear schedule. The video was created for those who have not seen the full process of building a turbojet engine and an aircraft for it, but want to see it!

From building a turbojet engine to flying - just one step, you need to say that they are not repairable, but more difficult, but quite maintainable. if not glued with superglue when assembling, then it can be repaired many times.

Remove the impeller of the Zelmer vacuum cleaner How to make emery reverse the engine from washing machine. How to connect the motor reverse circuit. How to reverse a reversible motor. Motor reverse circuit. How to connect the motor to the plow. Simple Reliable circuit diagram. READ TO THE END. How to make emery with your own hands at home yourself. Rotation in opposite directions. Easy fast simple.

A very useful invention from a vacuum cleaner engine

How to connect the engine to 220V. 380 to 220 volts. Sharpener. Sharpening device. Adapt. Homemade. Master Class. Hobby. Leisure. Home workshop. WARNING! THIS VIDEO SHOWS THE SCHEME OF STARTING THE REVERSE ON THE STARTING WINDING IN THE SHORT-TERM MODE. THE AUTHOR IS NOT RESPONSIBLE FOR YOUR INCORRECT ACTIONS AND ACTIONS. Subscribe to my channel.

How to connect a reverse motor from a washing machine to 220 easilySometimes this problem can be fixed in this way;) Vacuum cleaner Samsung SC4535. We disassemble the turbine. Hello friends! I found a solution to the problem that many craftsmen face and resort to using a hammer and chisel or screwdrivers. After many trials and different options pullers, I found a chic way, both in simplicity and in uniqueness. WE REMOVE THE BEARING WITH THE BEARING! just think about it;) If someone wants to buy such a puller, you can order me, I will do it for you. Further tests will be carried out on the crankshafts of the Chinese. Made in SashaDalkevich MY INSTAGRAM - FACEBOOK - Greetings friends on my motorcycle repair channel! My name is Alexander and at the age of 10, having collected the necessary amount of money, without any demand from my parents, I went to the market and bought a Karpaty moped, from that time my motorcycle career began. It's not a hobby or a job, it's part of my life. I take a very responsible approach to the repair of motor vehicles and, most importantly, I love quality in everything. What I can convey to you dear viewers and subscribers.

With your own hands: how to remove bearings from the crankshaft without a hammer and chisel