How to fit laminate flooring to a door frame. Step by step instructions on how to lay laminate flooring correctly. Ceramic coating has a number of advantages

Laying laminate flooring on a flat surface is not difficult. Certain difficulties may arise when laying laminate flooring begins doorway. This is due, first of all, to the fact that there are several ways to lay laminate flooring in a doorway.

You need to approach the installation of flooring responsibly, since here it is subject to more intensive use than, say, in the corners of rooms. Let's consider possible ways installation and technological nuances such styling.

Applicable options

As already noted, there are several methods of laying laminate used in doorways.

First option

This method is used mainly with properly planned major renovation or construction from scratch. It consists of the following:

Laminate flooring is laid prior to installation interior doors. That is, the installation of the laminate occurs in the usual manner, observing all technological gaps and other nuances.
After laying the laminate, the door frame and trim are installed, which hide all the technological gaps and cut edges of the boards.

Second option

This method involves cutting the door frame. In more detail this technology is as follows:

A cut is made on the door frame equal to the width of the lamella.
The cutting depth is about 1 cm, since it makes no sense to make the gap smaller.
The end of the lamella is inserted into this peculiar groove, forming an even joint.

This method requires a wood saw with fine teeth, accuracy and prudence.

Advice! The cut should be made as carefully as possible to avoid chips and splinters. It will be difficult to repair such defects later.

Third option

This method allows you to lay laminate flooring under the door without resorting to filing. This technology is more complex and at the same time simpler than the previous one and consists of the following:

A standard doorway is about 80 cm. Accordingly, a laminate board of the same size is installed. The thermal expansion of such a small board can be neglected.
Therefore, the laminate is measured and cut in such a way that there remains the smallest possible gap, almost flush.
The remaining gap is filled with sealant or putty of a suitable shade.

Advice! This method also requires accuracy and patience. It may take several tries to get the best results.

Some styling features

Like any process that has a certain complexity, laying laminate flooring in doorways has its own characteristics. Let's look at some of the nuances of proper installation:

Advice! In the doorway for docking various types For flooring, you can use a cork expansion joint. Its installation is somewhat more complicated than installing a threshold, but the structure is suitable for any combination of materials.

In conclusion, it can be noted that the doorway is one of the inconvenient places for laying laminate flooring. The considered methods of installing lamellas in such a place have general requirement: accuracy of calculations and precision of fitting operations. In any case, accuracy and some leisurely actions are required.

Good afternoon Please tell me how to properly lay laminate flooring in doorways and near pipe risers. I will have to install the flooring myself. In general, a master did the flooring work for me: he picked necessary materials, prepared the foundation. All that was left was to install the laminate, but he became seriously ill and would not be able to continue for the next 5-6 months. I decided to do everything myself. In principle, I imagine the procedure, but it’s specific places that confuse me, where I’m afraid of spoiling it.

Yes, valid when laying laminate special attention should be given to areas in the areas of doorways and places where communication elements are located. In this aspect, two methods of installing laminate flooring are relevant.

What about doorways?

Method No. 1

It is characterized by high labor costs, although this technology is the most optimal in the vast majority of cases. The door frame is cut to a height that will be sufficient for laying the laminate panel. But when performing such manipulations it is very important folk wisdom: “Measure seven times before cutting.” Here the main emphasis is on dimensional accuracy, since there is no chance to correct the situation.

Method number 2

More easy method, which involves working with a laminate panel. It is cut to size door jamb or other “protrusion”, leaving a gap from the wall. Near the doorway, a gap of no more than 5 mm is allowed. In addition, it will subsequently be closed with a special decorative strip, which will be installed in such a way that it will not interfere with the closing and opening of the door.

Particular attention to risers and pipelines

In this case, laying should be done in such a way that the transverse joint falls on the pipes. Or you need to pre-drill a special hole that completely matches the shape and size of the pipe. In this case, it is important to comply with the following condition: the size of the hole must be 20 mm larger than the diameter of the pipe. At the final stage of installation of the laminate flooring, the resulting gaps will be closed with special plugs that match the color of the floor.

Today, one of the most popular floor coverings is laminate. There is a lot to love about this material - it is relatively inexpensive, has a fairly long service life and looks great. I must say that the technology for laying it is not complicated. Perhaps the most important task is laying laminate flooring in the doorway.

As for everything else, then when proper preparation reason, there shouldn't be any problems.

Installation methods

The instructions for laying laminate flooring highlight only three different ways laying it in doorways:

First consists in the construction of special grooves. This is done like this: on both sides of the door frame, that is, on the bottom side on the slopes, cuts are made, into which the laminate panel is then inserted;

Advice! So as not to spoil appearance boxes, when cutting you should use a hacksaw for wood with small teeth, or a hacksaw for metal. The cuts are quite thin and neat.

Second way lies in the fact that the flooring is laid before the doors are installed. That is, at the moment when neither the doors nor the slopes are installed, the laminate is laid, and only after that the doorway is installed on top;

Third way lies in the fact that before laying the laminate in the doorway, a separate element is cut to the required size, that is, close to the slopes.

It should be clarified that the gaps are needed to compensate for thermal expansion. In this case, close to the slopes is allowed, since the thermal expansion of the wood is very small, and if we take into account that both the door slope and the panel itself are dry, then this value can be completely neglected.

It must also be said that this method is both simple and complex at once. The simplicity lies in the fact that sawing off a covering element is as easy as shelling pears, but the difficulty lies in the fact that doing it neatly and evenly along the contours of the door slopes is not entirely easy.

The methods described above, of course, help make the work easier, but it requires some special conditions, and it is carried out according to its own principles. For this reason, before laying laminate in a doorway, you should familiarize yourself with some of the features of laying this material in principle.

A little more about the first method

So, all the work can be described in several steps:

Preparation stage;

Stage of working with a saw;

Stage of laying the laminate panel.

The first step is to measure exactly where to make the cuts. This is quite easy to do. From the base you need to set aside a distance up along both jambs that will be equal to the sum.

This means that the cuts will have to be at the same height as the level of all other already laid flooring elements.

After all the measurements, you can start working with the saw. A hacksaw works great for wood, but with fine teeth.

The cuts are made very carefully along the marked lines. The depth of cut is calculated quite simply. You can verify this by studying the example calculation presented below.

After this, you can put the panel in its place. This is most conveniently done from the back of the threshold.

Calculation example

So, let the width of the doorway be 90 cm, that is, this is the distance between the two jambs. Let the length of the strip be 1.2 m.

Then the cuts must be made of the same depth on both sides, that is:

(1.2-0.9)/2=15 cm.

Advice! So that the cuts can be easily closed later, they should not be made too large. It is recommended to cut the panel. The optimal depth will be 1-2 cm.

Principles and features of working with laminate

As already mentioned, such work should be carried out with certain conditions. In addition, there are some principles and features. Accurate implementation of all of them guarantees success in your work.

Some rules

Before laying laminate flooring in a doorway, you should familiarize yourself with the rules for carrying out such work. All of them are aimed at long term service of this flooring.

So here are a few simple rules works:

When laying panels, it is necessary to leave expansion joints, that is, temperature gaps. All of them can be easily covered with plinths or special strips - thresholds. The gap size is selected based on the calculation of 2 mm per linear meter;

Before placing laminate flooring in a doorway, it is necessary to ventilate the room, since air humidity is also important. It should not exceed 70% at the time of work;

All joints at doorways can be covered with the above-mentioned aluminum thresholds. However, many people find them uncomfortable. As an alternative, you can use special profiles. Their price is lower, but they also look worse;

Direct laminate laying technology

Having considered all the rules and features, you should study all the steps of the work, since such work requires some order and sequence of actions.

Laying laminate under the door begins with preparing the base. The base must be perfectly level and dry. If we are talking about concrete, then all irregularities are puttied. If laying it yourself is done on wood, then all the boards should be secured, rotten areas should be eliminated, and so on.

After preparing the base, begin laying the substrate. It must be said that the substrate is a mandatory attribute. The backing can be purchased at any hardware store, where the laminate itself is sold.

The backing can be made of foamed polyethylene or cork.

After this, you can begin direct installation.

The doorway is finished with laminate using the floating method. In this case, you need to use the methods discussed above.

The floating method is that the laminate is attached to the base. In this case, glue should be applied only to the joints. Very often, glue is also used with locking panels - this will only strengthen this area.

Conclusion

As you can see, laying such flooring in doorways is not very difficult task, as in fact the whole work as a whole. To achieve the desired result, you need to follow all the tips and principles outlined above.

It must be said that often the material is laid not only on the threshold, but also on the slopes. Door slopes made from laminate is no worse than those slopes that are made from ordinary MDF panels.

Even more information on these issues can be found in the video in this article.

Laminate is the most popular type of finishing, and even an inexperienced person can handle its installation. The most difficult areas are places near pipes, near ledges and doorways. Before processing them, it is better to familiarize yourself with the advice of specialists and avoid mistakes.

Laminate is a covering that is assembled from panels, it has large number positive qualities, therefore it has become quite popular in the market. During assembly, special attention should be paid to the area near the threshold where the doors and opening are located.

To install laminate flooring, it is necessary to leave the material in the room where installation will take place for 2 days so that it acclimatizes and acquires the same temperature.

After preparing the base itself, you will need to lay the substrate on it, its joints are secured with tape, and the rows are glued to the base itself. For correct installation, you must first tension the fishing line, and only then lay the laminate panels along it.

You also need:

Make diagrams;
Think over the joint;
And it may be necessary to trim panels near pipes or doorways.

The second and subsequent rows are laid with a shift of exactly half the previous panel, this is necessary for good joining. The last row is trimmed if necessary, leaving the required gap near the wall; special attention should be paid to the doorway so that everything in the room is harmoniously laid out. After installation, you need to inspect the coating for defects or irregularities; such problems are eliminated with the help of wedges. After 24 hours, you can install panels for which a gap is left between the walls.

How best to lay laminate flooring in a doorway: stages

In order to avoid serious mistakes during work and after its completion, you need to know certain secrets and rules that will result in high-quality work and a strong connection.

Floor humidity plays an important role, because if it exceeds permissible norm, then even the most expensive and durable laminate can swell, ruining the appearance of the room.

During installation, you need to leave special seams in case of deformation; they are quite easy to hide and can save you in unforeseen situations. Immediately before installation, the room is thoroughly ventilated, and the humidity in the room itself should not exceed 70%.

Near the doorway, the joints can be covered with aluminum profiles:

They are quite comfortable;
They are of good quality;
More alternative, relative to analogues;
Easy to use, but short-lived.

In order not to encounter difficulties while working in front of the door frame, you need to follow several points. Measure the gap of the floor plane near the door; this indicator should be at least 10 mm, so that after completion of work the door can open and close freely and without obstacles. It is also necessary to look not only at the type of base, but also at the humidity in the room itself, and to join the sheets only after careful preparation of the surface.

You can lay laminate on such surfaces - old floor coverings, tiled and wooden floors, fiberboard bases, cement floor without seams. It is forbidden to lay laminate flooring on a thick carpet layer; such a base is too soft and can lead to damage to the covering. You cannot lay laminate flooring on xylitol floors due to the presence of high humidity in this material.

Laying laminate flooring at the door: popular methods

There are several ways to install laminate flooring in a doorway. In the first case, it is necessary to make cuts on the door slopes, into which laminate plates are then inserted. In order for the work to be carried out correctly, it is necessary to make markings for future cuts, and then, using a hacksaw with fine teeth, make several cuts.

For the second:

First, the floor covering is made;
Then the doors are installed;
Slopes are being made.

This option is the most convenient, and if possible, it is better to use it; this will greatly simplify the work, and you will not need to file certain areas. For the third method, when laying the laminate, you need to cut it to the required size so that it fits tightly to the slopes. This method is less professional, since if carried out carelessly, traces of installation will be visible.

Simple installation of laminate flooring under a door frame: rules and tips

You need to know how to choose the right laminate panels. Laminate is inferior to parquet, both in durability and in price category, this budget option floor covering. But even he can have certain subtleties, which must be taken into account when choosing this material.

Laminate is divided into classes - the first 3 are suitable for residential premises, and the next 3 are for offices and hotels.

Purchasing a certain type of laminate depends on:

What is the size of the room?
How many people are there;
What cross-country ability?

The larger the territory of the house, and the more people live there, the higher the figure should be. Experts do not recommend using the thickness of the coating; as an advantage, most often, 8 mm is enough for the average family. It is better to focus on the quality of the material, price category and manufacturer.

You definitely need to buy a thick substrate; it’s better not to skimp on it, because in addition to waterproofing properties, it also provides sound insulation.

Also quality material the required thickness can smooth out unevenness concrete covering, improving the future appearance of the laid laminate. In a cheap version, the substrate is made of polyethylene foam; it has sufficient moisture resistance, is not interesting to rodents and insects, but is also very fragile and can quickly tear or wrinkle. In an expensive product, it consists of balsa wood, being an environmentally friendly material, providing excellent sound and heat insulation. This type has a long service life and is easy to install.

Medium-priced substrates are made from kraft paper and expanded polystyrene. They are inferior to cork sheets in quality, but have a more affordable price category. Particular attention should be paid when choosing a laminate to the quality of impregnation. The laminate consists of 4 layers, which are connected by impregnation; if the company does not provide a quality certificate, it may contain harmful formaldehydes that can not only cause serious allergic reactions, but also cause significant harm to both adults and children.

Laying laminate flooring in a doorway (video)

When choosing products, you must pay attention to the accompanying documentation, if the manufacturer carried out all processes in compliance with the standards European quality, then you will definitely provide a certificate.

When laying laminate flooring in a doorway, a gap is formed between the laminate and the door frame. For high-quality styling laminate is unacceptable. You can eliminate the gap by laying laminate under door frame.

In order to place the laminate under the door frame, it must be filed (shortened). The laminate is placed into the resulting cavity. It is necessary to cut the door frame to the thickness of the laminate panel + the thickness of the substrate. It is convenient to saw a door frame using a special saw designed just for this job. If you don't have one, you can use a regular wood saw with small tooth.

Fig.1.

You can cut the box evenly and accurately using the following method. A backing under the laminate is placed next to the door frame. Laminate board is laid on the substrate reverse side up, so the front side will not be damaged during sawing. Then, resting the saw on the laminate board, they saw down the door frame. The cut can be made through, i.e. completely cut down part of the box. You can also make a cut to a depth of 10 - 15 mm, and cut off the unnecessary part of the box with a chisel.

Fig.2.

After the cut in the box is made, you can lay the laminate in the doorway. To do this, you need to saw off the laminate board to the shape of the opening. Then place the board under the door frame by 5 - 10 mm. It is important to take into account that the laminate under the door frame must be laid with a gap to the wall. This gap will allow the laminate to expand as the room temperature changes.

Fig.3.

The final stage of laying laminate flooring in a doorway is installing the strip. The plank hides the joint between the floor coverings of adjacent rooms. The plank is fixed to the base of the floor at the junction of the floor coverings. It's simple, but it's important to choose the right bar. If the floor coverings have one level, then a single-level plank is used. If the coatings are of different levels, e.g. ceramic tiles and laminate, then it is necessary to use a multi-level plank.

Despite the fact that laying laminate in a doorway is a fairly simple operation, many mistakes are often made that either lead to damage to the laminate and door frame, or the appearance of the joint between the door frame and laminate leaves much to be desired.

List of the most common mistakes when laying laminate flooring in a doorway:

Laying laminate close to the door frame. With this approach, the joint does not seem to be visible, but the absence of a gap will not allow the laminate to expand with temperature fluctuations, which will lead to swelling of the floor. In addition, accurately cutting a laminate panel so that it fits without a gap is very difficult and requires time-consuming adjustment.
Treating the joint with colored grout for laminate flooring. In principle, there is a way out, but a large layer of grout will look bad, to put it mildly. Over time, the grout will crack and fall off.
When trimming a door frame, you need to use a saw with a fine tooth. Often, a regular hacksaw is used to trim a door frame, without paying attention to the size of the tooth. If the tooth is large, then most likely the cut will not be even, and the door frame may be damaged. At the same time, a small tooth will make an even and precise cut and will not leave burrs.

We looked at how to simply and beautifully lay laminate flooring in a door frame. All that is needed for this is to carefully file the door frame and place the laminate under it. This work does not require any special tools; it is enough to have a wood saw with a fine tooth. Laminate laid in this way forms an ideal joint in the doorway, which looks great in any interior.