Do-it-yourself bolts for swing gates. Good bolts for gates - forging elements A small photo gallery of photos - bolts for gates photo forging

Swing gates are very convenient both in a private house and in a garage. To make them easier to use, that is, to quickly and securely lock, firmly fix and easily open, it is necessary to install such additional element like a deadbolt. A good deadbolt simplifies gate operations and makes them more reliable. In most cases, the deadbolt can only be opened from the inside and does not require keys. It cannot be opened from the outside, using a lockpick or picking keys.

What are the types of bolts

Some types of deadbolts can be purchased at hardware stores. But most owners prefer to make a deadbolt for swing gate with your own hands. The material can be wood (bars) or metal - strips, channels, rods.

Wooden bolts are most often installed on wooden ones. entrance gate, and metal ones are suitable for any type of gate - wooden, metal, made of profile, combined. Manufacturing methods may also vary. Very beautiful and reliable forged bolts. However, for their manufacture, it is necessary to have special skills in working with metal and a home forge, which is rare today. Therefore, in the manufacture of bolts for gates at home, conventional tools are used - drills, grinders, welding machines.

Bolt types:

Swivel. These are bolts of the "Turnwheel" or "Barrier" types. They are easy to manufacture, reliable and perfectly hold the gate leaves. Often made from wooden beam. The disadvantage is their visual "heaviness" and "old-fashioned". Although in some types of design it can be the main advantage.
Sliding horizontal. It can be either simple strip bolts or "espagnolette" bolts. They are attached to one of the sashes and fix either one sash to the other, or the sash to the frame. Usually, at least one of the sashes is also fixed with a vertical bolt or latch.
Sliding vertical. Each sash is fixed separately and can be held both in the closed and in the open state. They are attached either at the bottom or (less often and only if there is a solid frame) at the top of the gate.

Consider the manufacture of each type of deadbolt in more detail.

Do-it-yourself "Turntable" device

pinwheel- one of the oldest and most popular types of deadbolt. It can be used at entry or garage doors ah, often used to lock barns, sheds and other rooms where there are double-leaf swing gates. This is the most "popular" and easy-to-make type. The main advantage is that it is very easy to make it yourself.

A similar deadbolt for swing gates will have to be done with your own hands also because they are not produced industrially. It is made separately for each gate.

Take a bar or steel strip (thin channel) of the required length. The recommended length is approximately 2/3 of the width of the gate leaf, so that it captures at least a third of each leaf for security. Usually it is equal to a meter. If it is a wooden beam, then its thickness should be at least 5 mm, if it is a steel strip, then from 5 mm with a width of about 50 mm.
In one of the wings, not far from the edge (60-100 mm), it is necessary to make a through hole for the M10 - M12 bolt. The bolt must have a wide head and sufficient length (gate thickness + striker bar thickness + 2 washers thickness + space for 2 nuts).
The head of the bolt must not be visible or have edges ground off so that it cannot be unscrewed from the outside.
A beam or channel is drilled in the middle and put on a bolt, secured with locknuts.
Fixed channels are fixed on both wings, into which the beam or strip enters when turning. The slots can be made wedge-shaped so that the leaves are stronger and easier to pull when closing.

This type of bolt is characterized by high strength, reliability and clamping capacity. In addition, it is very popular with those who strive to do everything themselves.

The thickness of the wooden beam must be at least 50 mm for constipation

Bolt on the gate type "barrier"

This swivel bolt is also used frequently. It can be made of a wooden beam or an iron strip (channel).

Mark the hole on the strip for the hole for the M10 - M12 bolt. The hole is not made in the middle, as in the previous case, but at a distance of 60-80 mm from one of the ends. The bolt length is calculated as in the previous case.
A place is marked for a hole on the gate leaf (by attaching a deadbolt in the door in place) and a through hole of the appropriate diameter is drilled. It should be noted that in this case the bolt carries a power load, so the head must be wide, providing a reliable stop for the bolt.

The head of the bolt must not twist from the outside. Therefore, it must either be hidden under the coating, or have sharpened edges.

Three grips are made on the wings. One is on the same leaf where the bolt is attached, next to the end of the gate. The second one is opposite it, near the end of the second leaf, and the third one is near the far end of the bolt. If necessary, eyelets for a padlock can be made in it.

How to make a sliding bolt for the gate

This is also a very common design. Once such bolts were made of wood, but today the more common material is steel strips. Making it yourself is not difficult, having a set of tools and locksmith skills.

Take a steel strip about 400 mm long and about 50 mm wide.
The strip must move in special guide grooves. These guides can be fixed to the plate by welding and then the bolt can be attached to the sash with self-tapping screws or welding.
After the deadbolt is fixed on one sash, another groove is fixed on the second, which will fix the second sash.

This type of deadbolt is often supplied with a shackle in order to fix it with a padlock.

Make your own latch type "espagnolette"

For a deadbolt, a smooth rod with a diameter of at least 10 mm is best suited. A handle is attached to the rod to form a T-shape (the easiest way is by welding, but you can also drill a hole in the rod, cut a thread and screw a bolt into it). It is also necessary to select a steel tube with such an internal diameter that the flow enters it without delays and backlashes.

Cut the tube into three parts - a long one (about 10 cm) and two short ones (5 cm each).
Weld a long tube to one of the wings. On the opposite sash, weld a shorter segment so that the rod enters it.
Having inserted the rod into the tubes to the end, put another short piece of tube on the free end and attach it by welding. Make sure the gate opens and closes freely.
In order for the deadbolt to be fixed in the closed state, weld a metal plate or corner that fixes the handle in this position. You can add a padlock eye to the plate to secure the deadbolt.

Vertical bolts for swing gates

Such deadbolts most often perform an auxiliary function, they securely fix the lower part of the gate, and also help to keep the leaves in open position. They also use a rod with a diameter of at least 10 mm, L-shaped and a tube of the corresponding inner diameter.

The tube is welded at the bottom of the gate.
A pin is inserted into it and fixed in a hole in the ground, base concrete or gate frame.
In order for the deadbolt to be fixed in the open position, an additional stop can be welded to the sash.

Top vertical bolts can be used in garage doors to secure them more securely. In this case, an additional emphasis is needed so that the bolt does not fall out when opening.

Elements of artistic forging have excellent aesthetic characteristics.

From a technological point of view, creating a gate using the hot forging method is not a complicated procedure.

Consider the specifics of making a forged gate with your own hands.

Preparation of drawings and tools

Production begins with the creation of a drawing. It is necessary to display the metal structure with forged artistic elements as accurately as possible, and additionally prepare a specification. It specifies the following aspects:

position numbers;
number and name constituent elements;
conventions.

The specification consists of several sections: prefabricated units, parts, kits, materials, documentation, standardized products. When drawing up a drawing, it is necessary to take into account the ratio of the width, length and height of the product. The indicated dimensions must exactly correspond to the actual parameters. Permissible loads should be taken into account, the rules of ESKD and GOST should be taken into account.

The preparation of the drawing is carried out using special tools, the use of appropriate computer programs is also welcome.

It is important to be accurate when scaling in order to avoid errors in the manufacturing process of the gate. The drawings must contain the dimensions of the structure, the standard option is a gate with a height of 150 cm. We take into account that it will be raised above the ground by 10 cm, therefore, frame height will be 140cm. The gate will be located between the brick pillars with a gap of 100 cm.

Sketch of a forged gate with a gate

It is required to prepare a tool for work:

anvil;
vise;
Grinder;
welding machine - a mobile device for arc welding;
machines - torsion bar, snail, eccentric - are used for cold forging;
grinder - in the process of work, you will have to cut and grind metal parts.

You will definitely need a forge, tongs and hammers, do not forget about the stitches needed to make holes. It is important to provide an open flame source capable of generating a temperature of 1180°C.

Forging process

The process consists of several stages:

heating the blank;
swage;
blank;
final finishing.

Initially, the ingot is heated to 300 ° C, after which it is placed in an oven, where it is gradually heated to maximum temperature. Having removed the blank from the furnace, it should be compacted with hammer blows, rolling in a circle. It is during the crimping process that the scale formed during the heating process will be removed. Hammering is carried out in two stages: first, a blank is made, and at the end, the product is subjected to final finishing.

The gate will consist of several structural elements:

frame - profile pipe 30x20;
awnings;
patterns - stripes 12x6, square 10x10, 12x12;
supports;
locks and latches.

The supports are metal elements necessary for fastening the gate. The main structure is the frame, the canopies act as a connecting element, and the forged parts decorate the product.

The base will have classical rectangular shape made of 4 metal profiles. Initially, a profile pipe is cut, from which the frame is assembled, the evenness of all diagonals is checked using a tape measure. Welding of parts is carried out with tacks on the side and top, and after that the seams are welded, and the arc is cut.

Patterns will be made from ordinary reinforcing bars, cut in accordance with the dimensions indicated in the drawing. Workpieces are preheated in gas forge for 5 minutes, after which a pattern " Goose foot". It is necessary to insert a rod between the rollers and perform several rolls of a 10x10 square, after which a pattern is formed on the ribbed part of the equipment. The curls are bent on the "Snail", which allows you to effectively deform the cold fittings. However, to obtain an even pattern, the workpiece must be heated.

It is forbidden to cool the workpiece by lowering it into water, as this will lead to hardening of the metal. The subsequent formation of curls using this blank will lead to equipment failure or excessive deformation of the curl.

The material for the manufacture of curls will be a 12x6 strip, the heating of which is not necessary. Manufacturing faceted peak again, it will be performed on the "Eccentric", in this case, the rolling of the workpiece is carried out gradually, after each stage it is rotated by 90 °. You can do without the "Eccentric", just apply on steel sheet(5mm) dimensions. The resulting triangles are cut out with a grinder, after which the elements are given a three-dimensional look. This is achieved by removing the angles from the workpieces under the required slope, for which they use a grinder. It is also permissible to heat the part by gas welding and give the product the desired volume with a hammer.

The peak will be attached to spiral quadrilateral. It is necessary to cut off the workpiece of the appropriate size and make risks on it at a distance of 10 cm according to the number of sections with spirals. The workpiece is clamped in a vise at the level where the spiral is supposed to begin. Taking the curved yews, we clamp the quadrangle along the line with the ends of the turns. By rotating the yew along the axis of the workpiece, we create a spiral, which will be used to set the peak.

Worthy of special attention radius figures made from 3 mm sheet metal. Having drawn the required pattern on the sheet, we cut off a 20 mm high ring from the pipe, subsequently welded to the extreme bending point. Having attached the quadrangle to the ring going at the beginning of the drawing, we grab it by welding. When performing a bend, pull the workpiece over the edge and tap with a hammer at the bend, thus relieving stress. This is how you should move from bend to bend, grabbing them with welding.

Rolling clamps is performed using a strip of 20x2mm, it is with its help that the welding spots will subsequently be masked. Twisting side bars performed on the "Torsion", it is necessary to mark with chalk the place of twisting the square and fix the workpiece on the machine. You should clamp the square on one side, and connect the opposite segment to the rotating part. This is where clamps come in handy, providing excellent grip. When twisting, count the number of turns, do not do more than two with a gap of 15 cm.

When the components are ready, you can start welding. The main task is to maintain symmetry. Joints up to 1 cm long are thoroughly boiled with high currents.

After that, the welding site is cleaned grinder and then with a wire brush. The aesthetics of the product will be given by pre-prepared clamps mounted at the welding site.

The manufactured elements will be required to decorate the upper part of the gate, and below will be used leaflets. You can use stamped products made using 2 mm sheet steel. The assembly of the curls of the lower part of the picture begins with the formation of an arc, this will achieve symmetry.

To securely fasten the sheets, it is recommended to cut them at an angle relative to a square with a rolled end, as a result you will get a solid decorative element. When fixing the pattern, it is necessary to carry out tack welding using low currents, otherwise you can burn through the product. Welding must be carried out in such a way that the seams are formed from the wrong side, otherwise the aesthetic characteristics will suffer.

In the following video, you can clearly see the process of creating a wrought iron gate:

Installation of supports

The gate will be fastened with supports - this is the installation metal, which acts as an intermediate link, allowing attach the frame to the posts. Used for this purpose metallic profile, the canopies necessary to secure the gate itself will be attached to it. It is necessary to cut the profile into four segments, which, after being attached to the base, will protrude outwards by 4 cm.

Additionally, you will need to cut a profile comparable in height to the frame itself. We will fasten the gate to brick pillar , it is necessary to combine the process of laying and installation. The basis of the pillar will be our main metal profile, lined with bricks, it is to it that four segments are attached by welding. Bricks located opposite the embedded elements should be cut with a grinder. Four days later, when the pillar has gained strength, you need to attach a long metal profile to the embedded parts.

Hanging a gate

Now you can start hanging the gate, for this purpose point canopies will be used. Products consist of two components, one of the segments is equipped with a pin, and the other has a groove. The segment equipped with a pin should be connected by welding with vertical profiles basics. An element equipped with a groove is connected in the same way to the installation part of the product. Welds formed as a result of work should be carefully cleaned.

Fixing canopies to structural elements should be done before installing the frame on the support, since during the welding process there is a possibility of damage to the brickwork.

The finishing touch will be smooth welding of canopies and thorough cleaning of surfaces.

Painting and patina

However, our gate needs to be given a finished look, and this is impossible without painting. Necessary clean and degrease the surface, perform a primer, then carefully paint. Special attention should be given to the clamps, as moisture will accumulate under them, therefore, corrosion is likely to occur there. It is between the curls and collars that you need to use paint liberally.

You can give the product the effect of antiquity by applying patina, for this you need a brush having a width of 3cm. It is recommended to cut the brush before painting to give the bristles extra rigidity.

It is necessary to grind the paint on the palette until it becomes semi-dry, after which it is applied to convex forged elements, for example, the ends of the curls, sheets or clamps. Only now the work can be considered completed, the gate is ready for operation.

Men aspire more attention devote not only to the arrangement of their private property, but also to protect it, regardless of whether it is a garage or your own yard. Their faces are most often represented by gates or entrance gates. And not always the main role is played by their beauty. Much more important is the safety and protection of them from unwanted visitors. Therefore, more often the owners are attracted by a reliable constipation for the gate. Why is it needed?

Any standard lock requires keys. And if the keys are lost, the gate can be securely locked with an additional latch or deadbolt. Now there are several types of locking mechanisms and deadbolts that do not require keys. But, in general, any door, including a gate, must have some kind of device that will fix it in the open or closed position.

Most often, vertical valves are used. Such a convenient and simple constipation ensures the fixation of any door or gate. For strengthening, thick metal rods with levers are used, which are fixed in special holes in the floor or ceiling. Such locks are still used in mortise gates, only they are smaller. But they are used simply to close the gate door.

Self-closing latch

The mechanism is self-closing

You can also make a latch that will snap into place by itself. On the door you need to install a flat fixed metal bar. When the gate is closed, the lever engages with this plate. The latch itself is fixed with one bolt. And another bolt is screwed nearby in order to limit the movement of the lever. To open such a latch, just press the lever, it will release the bar. To close the gate, it is often enough just to push the door so that it slams shut.

The most common among gate locks are horizontal heck. They are attached to all types of gates. Such locks have the simplest device, consisting of a rod, a fixing lug and a special holder. And the principle of their work is similar to the action of vertical locking devices. There is different types overhead sliding locks. The mechanism of such heck is easily attached to any canvas. The flat bar provides sufficient security of constipation. It can be installed both internally and externally. For greater fixation on the mechanism from the outside, you can put on a padlock, which is installed on special ears.

Screw constipation

Screw-type locking mechanisms are installed from the outside. Their device is also quite simple to use. Consists of a threaded rod and a key base. This base has a special notch and small size spire. Special key drives the shutter system. It is quite easy to assemble a screw lock yourself, however, the complexity of such a mechanism lies elsewhere: in the gate opening there is often not enough space to accommodate a threaded recess where the rod itself is screwed. But such a constipation is easy to break when selecting a similar key.

Groove constipation

With their simple device, such constipations have high level burglary protection. The principle of operation of the lock is as follows: the key inserted into the lock slot by rotation drives the rotary gear mechanism, which opens or closes the door.
In the role of clamps, valves with a spring base are used. The spring mechanism will allow effortless actuation of the constipation.

Locks for the gate with a latch and a rope inside

To mount such a bolt with a rope, you need a latch, which is equipped with a locking device on one side. It is fixed at an angle of 40 0.

Then a strong cord is threaded through the guide rings, the end of which is placed in a place accessible to the hands. To open the gate for this end you need to pull. Such constipation is convenient only for the owners. Guests may "experience" difficulties. It is good to install this constipation on metal gates. A rope is attached to the latch, with which the door can be opened from the outside and a latch to open the lock from the inside. In order for the latch to interact with the beam, the lower part of the latch is ground at an angle.

secret castle

Sometimes on the canvas neither a well for a key nor a hole for a lock is visible, and the gate does not open, as if there is a lock from inside. If you look at the canvas more closely, you can find, however, that with reverse side there is a latch. But how it closes from the outside, at first the mechanism of this constipation is not clear. It turns out that there is a hexagonal screw head on the door. It is turned with a special hexagonal key. On the inside there is a rail, which, when the bolt is turned, closes the door locking device by rotation. Make such constipation quite easily.

A flat flat is made on the tail of the bolt with a file. A latch is fixed on it, in which a slot is made for the flat.

Constipation is collected like this:

drill a special hole for the threaded section of the bolt;
a recess for the bolt head is made with a thick drill so that it can sink into the recess on the canvas;
on the other hand, two washers are put on the bolt and pressed with a nut so that the bolt head is sunk;
a valve is placed on the prepared flat and pressed tightly with a nut.

Hidden gate valve

Often, the owners want to install such a valve on the gate in their yard or in the country, in addition to the castle, which is difficult to detect and open. Such a valve is made on a wooden gate.

Suppose such a bolt closes down. To install it, you need to drive a pipe about 0.5 m long into the ground. Location of the pipe: from the side of the site, where the gate opens. The pipe is chosen with the same diameter as the bar. Brackets are attached to it, another bar is inserted into them, which, slipping through the brackets, will fall into the pipe. The bars should not protrude anywhere. You can also add a chain.

On the video there is another version of a do-it-yourself bolt:

When the owner wants to secure a plot or a building for a garage from intruders or unauthorized persons, he puts up a massive gate. To enhance protection, they can be equipped with bolts, and the devices will create an additional obstacle to unauthorized intrusion. Self-manufacturing bolting is a simple task.
Its features depend on the type of particular mechanism.
Deadbolts are:

sliding;
Swivel;
Crossbar.

To make a bolt with your own hands, which will protect the swing gate, you will need a certain set of tools.

It includes:

Channels;
Heck;
Wooden blocks;
Nails and bolts;
Strong cord.

Of the electrical equipment, welding equipment and a drill with a drill that perforates a metal surface are useful.

Types of bolts for double-leaf gates

The devices that we will consider below are well suited for double-leaf entrance groups. And the owner can make each type of product at home.

"Barrier" - the most common deadbolt for double-leaf gates

"Pinwheel"

This type of deadbolt is found on the gates of garages and various outbuildings, which are closed using double-leaf swing gates or doors (perhaps they were also made by hand). "Turntable" - the most primitive device, the moving part of which is a wooden block.

Bolt "Turn" for double-leaf gates

The parameters of this part are as follows:

Length - at least 1.5 m.
Thickness - from 5 to 10 cm.

Hold on wooden beams will be on channels. They are attached to the gate with a through bolt, achieving complete immobility. The hole is drilled with a drill with a nozzle for metal. If there is no drill, the work is done welding machine. One channel is attached a little higher, the second - lower. The bar is fixed in the central part of the edge of the canvas, which opens inward. Its rotation should be counterclockwise.

"Barrier"

It is also easy to put this bolt on the swing gate with your own hands.

Bolt "Barrier" is used on the street side of the gate

A bar or iron plate up to 60 cm long is bolted to the sash (1/3 from the edge).
Two channels 10 cm long are welded. The width of the elements must correspond to the timber. When working with a plate, the channel is replaced with a cut one. metal corner(the plate must be firmly embedded between the part and the sash).

If there is a desire to equip the “barrier” with a padlock, a loop is welded on one side of the plate for locking. The second ring is attached to the sash .

"Latch"

The model will become more functional when combined with vertical constipation. It is made from a tube Ø 10 mm or more. The material is cut into 3 pieces with a length of one about 10 cm and two others - 5 cm each.

Espagnolette is best used with vertical deadbolts

The longest part is welded horizontally to the edge of the canvas. One 5 cm piece is welded along the edge opposite to the first tube. Next, a latch bent from a T-shaped pin is threaded into them (for its manufacture, the rod is selected according to the diameter so that it easily enters the tube). The latch is moved all the way and the 3rd pipe section is welded to its edge.

The lock is fixed by attaching a piece of metal plate under the handle. For a padlock, an easy entry of the handle into the eyelets with loops is provided. .

Deadbolt with locking mechanism

This option is considered ideal for high iron gates. A deadbolt with a locking mechanism is made as follows:

A piece of reinforcement with a diameter of 15 cm (the so-called finger) is welded at the top of the box. During operation, another curved finger, fixed with an anchor rod, will go behind it.
The anchor rod itself is attached to a piece of pipe of a suitable diameter. Another piece is positioned below the center point. After fixing the rod, the bottom of the lower tube is welded, after which the rotation of the anchor is checked.
A hole is sawn in the anchor rod with a grinder and a hardened iron plate is inserted, securing with a bolt. A hook is made on the second canvas, behind which the plate will go when the gate is closed.

Universal bolt options

With a latch and a rope

To make such a bolt on the gate with your own hands, you will need a latch with latches located on one side. It is attached to the door, adhering to an angle of 40 °.

A strong rope is threaded through the rings and its end is left in a safe place. The gate opens at the moment when a person pulls the cord. The owner of the yard will like this method of protection, but unauthorized persons are unlikely to be able to get into the site.

Hasp with beam and latch

The tricky design consists of a bar that rotates on a round panel. Such a bolt opens from the inside with a handle. To enhance the reliability of the mechanism, a latch is installed, which can also be opened only from the inside. The interaction of the latch with the beam is provided by slightly grinding its lower part obliquely.

sliding deadbolt

It is easy to make a deadbolt of such a plan with your own hands for both the gate and the gate. The principle of operation is the same. The manufacture of the product takes one metal plate with parameters of 50 mm in width and about 40 cm in length. Subsequently, the part will "ride" back and forth along special grooves.

Pretty common design. Previously, such deadbolts were made of wood, but now a common material is steel strips.

The grooves themselves are fixed with bolts or by welding work. A plate is inserted into them and for greater reliability they provide entrance group vertical bolts. This part of the structure is obtained from L-shaped pins Ø 10 mm. To protect the garage door, the stop is fixed at the top of the canvas so that it can be fixed when closed. In other cases, where swing gates are used, two vertical bolts are equipped in the lower part.

It seems to be "little things", purely technical devices. But the little things that are extremely important for operation gate with forging elements. Therefore, first of all, they must have suitable dimensions, be correctly installed on the gate, and secondly, you need to pay attention to their appearance. Which gates need bolts? It turns out that it is necessary to put bolts not on all gates, but only on gates of a certain design. This design is called - swing gate. It is their operation that is practically impossible without the installation of bolts, latches or bolts. And the work of bolts and latches on the gate is closely related to gate locks, especially for garage doors, but equally applies to any swing gates. The history of the gate, if we look at the photo of the old gate, shows us that a variety of bolts have always been present on any gate. Today, one can only marvel at the art and ingenuity of forging masters with which they approached the solution of a technical problem - the manufacture of bolts for gates and various latches. Sometimes creating very intricate designs from forged metal, striking with the thoroughness of work and intricacy decorative look bolts and latches. Harmoniously complementing the sketch for decorating the gate, along with another forging element that has a direct practical value in construction metal swing gates- ancient hinges, on which we will not dwell in detail now. But you can see photos of old loops and read about their manufacture.

Modern good gate bolts have approximately the same device and structural elements as their predecessors, the idea of \u200b\u200bcreating a gate bolt is so simple and reasonable that the design of the gate bolt has not undergone significant changes over the entire existence of swing gates. But decoration and ways to make beautiful bolts on the gate changed in accordance with fashion trends in different years. Today, the most beautiful and most prestigious are those gate valves that we call - these are forged bolts for gates decorated in antique style. They imitate antique bolts, creating a pleasant style suitable for decorating many modern wrought iron gates for houses, estates, cottages and other buildings. Where to buy gate bolts? It turns out that the sale of forged latches and bolts is not so developed and it can be problematic to find them in a store. Especially if you take into account the fact that you often need to find and buy some special bolts that have a very specific design, suitable for the so-called individual gates. Best of all, if you want to buy bolts for gates with a design or buy decorative, beautiful forged bolts, then you need to contact art forging workshop. Where you can be offered not only interesting design bolt for gates with forging, but they can also make a latch according to an individual artistic sketch. The design of the bolt for the gate and its appearance should fit the overall style as best as possible. gate decoration is an axiom if you can use this expression in relation to decorative arts. Installation finished product from metal, you can do it yourself, if there is such a desire, but it is better to entrust the work to a specialist. How to install a deadbolt for a gate with your own hands, you can be advised by a master's consultation for free.

The simplest gate bolts are cheap, reliable and practical, you can buy inexpensively.

Gates with forging elements - forged bolts and locks photo.

This photo of bolts for gates serves as an interesting illustration of the fact that even the simplest bolts and latches, artistic forging of metal for gates, can be made inexpensive, cheap and beautiful at the same time, giving them an original and unexpected look. No need to give too of great importance that all locking mechanisms are on inside gate with forging elements and not visible from the street. Make them beautiful - just does not fit. After all, it will be more pleasant to use all these constipations yourself. Moreover, there will be a whole bunch of all kinds of bolts and latches on forged gates. See what the inside of the gate looks like with forging elements. The photo is useful and entertaining. Especially useful for those who think how to make a wrought iron gate. And for those who want to learn how to install gate bolts with their own hands at home. By the way, do not forget that most often the bolts and latches on the gate help us to install WELDING metal with electrodes . …………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………..

small photo photo gallery — bolts for gates photo forging.

Old gates with forging elements - locks and bolts, locks and latches.

Sooner or later, your gates with forging elements get old, but even then bolts, latches, locks and locks will remain bright details in the design of the gate.

Gates with forging elements - stylization of bolts "antique" photo.

The effect of antiquity is what is traditionally valued in the art of forging. That is why many products, parts and mechanisms are specially styled "antique" immediately, when they are made in the forge. Important point in the work of a blacksmith. In order to do metal forging with your own hands, you need to undergo forging training. One of the options is a master class on forging metal. On one's own the basics of blacksmithing can be studied from books forging literature, download for free and read without problems.

It is advantageous to decorate gates with forging elements with beautiful bolts - photo.

It is advisable to consider latches, locks, bolts and latches as important independent forging elements that complement the overall picture of a wrought iron gate pattern. In most cases, the production of wrought iron gates in Dnepropetrovsk assumes that the customer does not bother much and he does not have to "puzzle his head" choosing valves. We ourselves in the forge will come up with everything and make forged bolts suitable in style for overall design gate with forging elements. At certain conditions, these little things can take center stage in the design. For example, in this photo there is a gate with forging elements. ……………………………………………………………………………………………………………………………………… ……………………………………………………………………………………………………………………………………… …..

Cheap bolts for gates - latches from a thick rod photo.

If we are talking about inexpensive gates with forging elements, then it is permissible to get by with the simplest locks, locks and bolts. Or buy ready-made latches suitable in size. We have to look at the situation. Simple, without imagination, but inexpensive and practical. And that means he has the right to life. ……………………………………………………………………………………………………………………………………… …………………………………………………………………………………………………………………………………….

How to paint good gate bolts and give them a beautiful look?

Simple constipation does not mean: bad and ugly valves. Even simple and uncomplicated do-it-yourself metal products can be made to look stylish and spectacular by painting. It's not difficult, but technology will help you do-it-yourself patination . A latch, a bolt or a hook, painted with ordinary paint, is additionally tinted with a blacksmith's patina. The photo shows an example of patination with copper patina over black paint.

Where can I put a bolt lock on the gate?

There are many highly original and technically ingenious gate locking systems. But in practice, it is most convenient to place a padlock on the gate with forging elements, as part of the deadbolt. In the design of a forged bolt, special loops are usually provided by the manufacturer. This method has existed for as long as bolts and padlocks have existed. An example of an old forged bolt on a gate with forging elements shows us that nothing has changed since those ancient times. ……………………………………………………………………………………………………………………………………… ………………………………………………………………………………………………………………………………………

Modern bolts, which you can buy and put on your gates with forging elements if you wish, have basically the same design. See the special eyelets in the photo?

What does it look like if we want to put beautiful forging elements on the gate and make the decoration of the gate? There are many options, for example, as in the photo. Try using such a mechanism to install a padlock on a gate with forging elements. The design is old, time-tested, looks original and beautiful. You yourself see. ……………………………………………………………………………………………………………………………………… ……………………………………………………………………………………………………………………………………… ……………………………………………

Good gate bolts can be made from wood and complement the design of wooden gates. Bolts for wooden gates photo.

Lock wooden gate Are you going to or will you leave them open all the time? Probably going, if not, then unsubscribe separately in the comments - I want to understand you better, to become closer to you. All other citizens of a more traditional orientation are used to locking their gates. This means in practice that we need to put bolts and locks on the gates. Is it logical? Who will help us? Only iron. A variety of iron bolts, but beautiful ones are better, which means again forging metal. We look at the photo. We see a certain extreme - a wooden bolt on a wooden gate. But even here we cannot pass by artistic forging. As you already begin to guess from my story, we put a beautiful forged bolt on a wooden gate and a miracle will happen. We will again have gates with forging elements. I hope this fact does not upset you. After all, we need a beautiful gate, and not a pile of firewood to kindle a fireplace. How to make a gate valve with your own hands and other forging elements for gates.

awesome work - photo gate with forging elements.

Even a little, even a drop of metal with decorative fantasy, multiplied by blacksmith art- this is real creativity, allowing you to make a small masterpiece. Even if this masterpiece of decorative art has a practical application - a gate with elements of forging from wood.

The simplest type of bolt for the gate - the latch can also be made skillfully and with original design. Artistic forging metal can make forged latches on gates, gates or doors. You can buy forged latches or order their manufacture. ……………………………………………………………………………………………………………………………………… ……………………………………………………………………………………………………………………………………… …………………………………………….