DIY raincoat fabric awning. How to make a protective sun cover for a car? Requires special threads

In this article we will look at how to make a protective cover for a car with your own hands, and whether this attribute is really necessary for your vehicle. After all, if you really love your “iron horse,” then you probably want it to always look its best. Then let's get to the fun part.

Protective cover-awning for a car - fabric features

Prolonged exposure to direct sun rays can have a detrimental effect on, in addition, the tent cover will serve as reliable protection from dust, dirt, moisture, as well as the harmful behavior of birds. And if you don’t have the opportunity to hide your car in the garage, or you just went on vacation and the car is forced to sit in the open sun for several weeks, then a car awning, even hastily made with your own hands, will serve as a real lifesaver.

Basically, such covers are made from special fabrics that do not allow dust and dirt to pass through, but due to their excellent breathability, they can provide excellent air circulation, so moisture has no chance of accumulating under such a car cover. Some of the most popular awning fabrics are Oxford And Tarpaulin, they can provide excellent protection and will last for quite a long period.

These materials have either a polyvinyl chloride or polyurethane coating, which is applied to the reverse side. The main advantages are lightness, excellent tensile strength, excellent operating temperature range, ease of maintenance, moisture resistance, excellent resistance to abrasion and contamination and fairly low susceptibility to ultraviolet radiation.

Car cover - how to sew?

Typically, such a cover consists of three parts: two side and one central, which runs along the roof, hood and trunk. When taking measurements, be guided not by the geometric data of the car’s base and body length, which are indicated in the car’s passport, but rather take a soft meter or a simple long cord and run it along the contour of the car from the bottom edge of the front bumper to the bottom edge of the rear bumper. Then measure its length with a tape measure and make a small margin, about 20-30 cm. The side cuts are also measured along the contour of the car, but in three places: along the hood, trunk and cabin roof. The margin is added, the resulting value is divided by two, and an approximate outline is drawn on the fabric based on three indicators. In this case, the protective cape for the car will be sewn from three longitudinal components.

You can do the sewing a little differently. Also use three parts, only not longitudinal, but transverse. Then you need to measure the length of the flap along the hood, along the cab, along the trunk using the same lace method, and do not forget to record the width of each such flap. The resulting patterns are also sewn together. The margin in the place where the mirrors are located needs to be made a little larger, up to 50 cm, depending on the size of these devices. But if you agree to keep the car with, then you don’t have to do this. You can complete the awning by pulling a lace or elastic along the contour so that the cape does not lie on the ground, for which you can make a hem and stitch it well; we even have a supply of fabric for this. Before taking this final step, throw the resulting canvas over the car to eliminate imperfections in the silhouette in any places.

What is a car tarpaulin made from?

There are several types of protective awnings. The most popular are universal reusable kits. This car cover is sewn from a special fabric that has all the qualities listed above. Next type serve as liquid awnings. This is a special substance that is applied to the surface with a brush; its feature is the ability to protect the surface of the car not only when parked, but also while driving. And the last type is vinyl films that are glued to cars.

In principle, it is quite possible to sew a fabric cover yourself; for this you just need to buy special fabric and devote special attention seams - they should be double hemmed. This is very important, since such seams will be softer and, accordingly, will not cause harm. paint coating Moreover, they will keep their shape perfectly.

The threads used must have increased strength; it is best for this purpose to take reinforced threads made of 100% polyester. They will not only easily withstand all cycles of use to which the car cover will be subjected, but will also be resistant to more significant loads that will arise during regular cleaning of dirt, leaves and snow.

To sew, you will need to measure the length, width and height of your car, but it is better not to make a pattern exactly according to size, but leave a little more margin, since a loose cut has a number of advantages.

Green grass and trees, but also various buildings. If there are children in the house, then there must be slides, sandboxes and swings in the yard. You can also place several gazebos on the site, where family celebrations and friendly gatherings will be held.

If we are talking about a private house and year-round living in it, then stationary structures. We recommend that summer residents pay attention to the tent gazebo.

Let's list its advantages:

• affordable price. For most Russians, this factor is decisive. Gazebo tents are cheaper than other structures, but are in no way inferior in quality or appearance;
• ease of installation. You don't need to hire a whole team of workers. You can cover it with an awning with your own hands using a minimal set of tools;
• mobility. Gazebo tents are easy to lift. They are quickly disassembled and transported to any vacation spot.

What materials are awnings and awnings for summer cottages made from?

Have you finished erecting a temporary structure, but don’t know what to cover it with? We offer several options for awnings for gazebos. You can easily find all materials in stores and markets.

Option number 1 - tarpaurin. It makes a very durable, but at the same time easy to lift awning.

Option number 2 - tarpaulin. It will provide protection from rain and wind. But due to the heavy weight of the material, certain problems with its installation may arise.

Option #3 – polyethylene film. One of the most accessible materials.

How to make an awning for gazebos with your own hands

How to make awnings for a summer residence with your own hands? We will tell you about this now.

List of required materials:

• 15 meters of nylon or thin tarpaulin (width 2 m);
• 3 meters of gauze 2 m wide;
• special glue for rubber.

How to make an awning for gazebos with your own hands (instructions):

1. Create a drawing on paper, indicating all the details of the awning. We depict the front wall of the half-tent in the form of a trapezoid with triangular roof. The width is 3.5 m and the height is 1 m. The rear wall will be the same in width. And the ratio of its height to the height of the front wall is 6:10. The “roof” of the rear wall should be flat, with 2 slopes dividing the top line into 3 parts.

2. Now we need to draw the side walls. They both have rectangular shape. The length is 2 m, and the width is 1 m. The roof will consist of 5 triangles that fan out from the center of the front wall. It is also necessary to draw the central triangle of the roof. Its acute angle should coincide with the “ridge” of the awning. From the left and from right side From the central triangle you need to place two similar figures.

3. Make a pattern, trace all the details on the fabric and cut them out. Then we sew the elements together with strong thread. It is best to do this with a linen seam. We glue the resulting gaps with thin strips of the same fabric, using special glue for rubber. We sew ties to the side ribs, with the help of which you can later stretch the awning and tie it to the trees in the garden. We install it with our own hands central pillar. We simply drive it into the ground using available tools. Next, we put the awning on the rack with the ridge, slowly stretching the sides.

4. After installing the awning, you need to sew a mesh or gauze to it. This will prevent mosquitoes, flies and other insects from getting inside the gazebo.

DIY terrace

An extension to the house will allow you to increase not only usable area home, but also its market value. In addition, you will get a great place for drinking tea and spending time in the fresh air.

The terrace joins the house and works together with it as a single unit. To achieve this, you need to use different anchors. They take on most of the load.

Recommendations for those who are planning to add an extension to their house

The terrace has a simple design. You can build it yourself without turning to third parties for help. But here too there are rules that should be taken into account.

Solid foundation

Any extension to the house needs a solid foundation. A foundation resting on the ground will reduce the subsidence of the structure. To reduce costs, we recommend using cast-in-place piles.

Lightweight terrace

The construction of an extension with a relatively light weight will allow minimizing the consequences of foundation settlement. Ideal option can be called frame structure. It consists of bent metal profiles. The walls are erected from foam plastic or foam blocks.

Interior and exterior finishing

Adding an extension to your home is only half the battle. It still needs to be brought into proper shape. Like all rooms, the terrace needs finishing. The outside of the extension can be “sheathed” plastic lining or MDF panels. For interior decoration you can use “liquid” wallpaper, wood or plaster.

Summer and vacation are an excellent combination for a backpacking trip. Hiking, tent, songs and stories around the fire, what could be better? But, of course, it’s worth preparing for and finding out in advance how to make a tent with your own hands.

The presented photographs illustrate the process of cutting and sewing a tourist tent, which can provide shelter for three people. For work, prepare 23 m of raincoat fabric (it is best to give preference to green). The photo below shows the layout of the fabric for cutting, as well as symbols.
The following photo shows the production of parts.

When all the parts are done, you can start assembling DIY tents. The very first to sew the ends and sides together (seam Ш-5 or Ш-2), the bottom will be secured next (Ш-5 or Ш-2), and last will be the awning Ш-1. Sewing the awning will be quite difficult due to its impressive size, which is why it is best to pre-mark the stitch line using chalk. And then do a hand stitch. Bring your imagination to work and use all the possibilities for making pockets, pegs, racks and covers.

The mass of the resulting product will be about 5 kg, if given weight is critical for you, you can reduce it by 2 kg by using nylon fabric for sewing. But keep in mind that it will be more expensive than a raincoat one. To give the tent a more formal look, you can make all seams Sh-1 (sew along the “face”, and then sew keeper tape onto it).

To work with raincoat fabric, use needle No. 120 and thread No. 30; to work with rubberized nylon - nylon thread K-20 or K-40. This choice This is due to the fact that moisture can accumulate in the places where the seams are laid and the cotton threads will soon literally rot. To combat water condensation, it is recommended to different heights place windows. For stitching, use an industrial sewing machine class 1022.

Find out more about it, because it is extremely interesting and exciting.

Canopies + gazebos + awnings and tents are very convenient structures for relaxation. They can be installed permanently in the country, suburban area, in a park, summer camp, or serve one-time for an event.

Design Features

Tents are sets of supports of different designs, onto which, after installation, awnings made of tarpaulin, fabric or film are stretched.

Advantages of choice

1. Deal with installation similar structure even one person can do it with their own hands.
2. When disassembled, the device does not take up much space. Thanks to this, it can be stored in a barn or other utility room.
3. There are also no problems with transporting the structure. Tent small size fits in the trunk of a car.
4. High-quality gazebo awnings can withstand heavy rains and strong winds.
5. On at the moment manufacturers make designs that have the most different sizes- from small buildings for a couple of users to spacious pavilions that, for example, can accommodate all the guests of your wedding. There are also tourist models and analogues for fishermen and hunters.

Pay attention! When installing a tent, please note that the ease of disassembling/assembling it, as well as mobility, is ensured due to the lightness of the structure. It is usually secured with ropes and long pegs, just like tourist tents. The second method of fastening is to use a tree as a support or anchor for the structure.

Types of structures

Often, simple summer residents are confused about the terms “tent” and “awning”. The first concept means a device made of rigid supports.

An awning is a protective canopy made of fabric or film. Previously, tents could even serve as camp houses. Now is best option collapsible gazebo.

At the moment there are 4 types of tent structures.

1. Tent tent. This compact and lightweight structure is usually supported by a quadrangular frame.
2. Gazebo tent. A very common option, produced with the most different numbers walls Has mass additional amenities and elements. For example - replaceable mosquito nets, windows, partitions. This “three in one” structure: gazebo + awning and tent, is suitable for use even in mild winters. Then the lightweight mesh is replaced by solid-type walls with wind protection.

1. Tourist tents are more compact. Their purpose is to protect travelers from the vagaries of the weather. They usually have wind braces.
2. The most spacious structure is a tent-pavilion. It can be used to organize crowded various events.
3. Industrial structures use special synthetic fabrics. For example, from polyester fibers. To increase the wind resistance of the canvas, it is reinforced with polyurethane threads.
4. Gazebo awnings must be impregnated with water-repellent compounds. This allows them to be used in rainy weather.
5. Product frames are made of aluminum, steel, fiberglass.

Manufacturing materials

Pay attention! Often, cheap structures are not particularly reliable. Based on this, if you want to use a tent gazebo for many years, do not skimp on its quality. Even though the price of the structure will be relatively high, you will ensure comfort for a long time.

Related articles:

How to build an awning gazebo yourself

A structure erected on your own will not only decorate the site, but will also protect your family and guests from the hot sun on a summer day and give you the opportunity to enjoy the coolness of the evening. In addition, the original tented gazebo will complement the surrounding landscape.

First technology option

1. You will need guides and rack supports with a length of approximately 2.5/3 m. The material for these elements can be rolled steel, metal pipes or wooden beams.
2. First, dig four holes in the corners of the future structure, about 50/70 cm deep. Install racks in them and secure them. Connect them with jumper guides.
3. To give the structure a greater level of strength, it is best to not just dig the pillars, but fill them with concrete.

1. Next, you can mount the roof frame. It can be either sloping or flat. The first option is preferable, because it will allow raindrops to roll off the awning without any problems.
2. To assemble the roof base, you need to connect 5 guides. Four of them will serve as the frame itself. The fifth pipe will become a reference point in the center of the structure.
3. Before sewing an awning for a gazebo, choose a material for it.

1. The best option is to purchase a tarpaulin or thick waterproof fabric. Please note that the canopy can be made so that it covers not only the roof frame, but also the walls of the gazebo.

Another way

1. First, select the material for the frame of the structure. It can be timber, aluminum, steel pipes or thick reinforcement or ready-made supports-racks with a factory fixing system.
2. Next, mark the construction site. For this purpose, use stakes to mark points for future supports.
3. After this, dig holes at least 50 centimeters deep. When the supports are installed, fill the holes with damp soil and compact them well. If the tent is large, then better rack concreted.
4. Next, wait until the soil on the awning gazebo supports settles or until the concrete dries.
5. Then start installation cross beams. Mount the side clamps on the supports, then insert the guides into them.
6. Bring the crossbars together in the center of the frame and secure with a special centering tool.
7. When there are no such parts in the structure of the structure, the beams can simply be fixed at the corners on the frame. Before installing the awning, make sure that the structure is secure.
8. Then tension the roofing material.

Pay attention! Before sewing an awning for a gazebo, please note that in addition to the traditional fabric analogue, you can also use modern version. For example, it could be polycarbonate.

1. In this case, the frame will need to be made 10/15 cm smaller than the covering sheets. For support posts, it is best to choose aluminum pipes.
2. If the awning has a rounded shape, steel pipes will be needed for the roof frame. They are fixed to the supports using bolts and angles. Polycarbonate plates are attached to them with self-tapping screws.

1. For an arched type analogue you need metal profile having longer length. One side of the post digs into the ground and is attached at an angle of forty-five degrees. Fix the other side in the same way at a point prepared in advance. This way you will get an arch shape. For strength, secure the sides at a height of 1/1.5 meter.

We sew a tent and give it water-repellent properties. So the season of vacations has arrived, going to the countryside, hiking and in nature for barbecue in a friendly company or fishing for the biggest catch) When going out into the countryside for several days, you can’t do without a tent, which you can buy, or you can sew yourself , with your own hands. Sewing a tent is not particularly difficult if you have suitable fabric at hand and sewing machine. The most important thing is to then bring this fabric into proper shape so that the tent is waterproof and keeps its shape.

We sew a tent and give it water-repellent properties

So, let's look at the description of sewing a tent with your own hands for going outdoors on a hike or fishing. By the way, if you prefer fishing, I suggest you take a look at the website eholot-lowrance.ru, which is an official Lowrance dealer. Here you can buy echo sounders, echo sounders, chart plotters and radars that can provide you with the best catch and great pleasure from this type of outdoor activity.

Rubberized percale or tent canvas is suitable for sewing a tent. The tent fabric is linen fabric impregnated with a special compound and dyed green.

We measure the required length and width of the future tent. Draw a pattern on paper. The tent should consist of a floor, a roof and four side parts. Moreover, one part (the front) will represent the entrance, and therefore requires the installation of a lightning bolt.

After drawing the pattern, transfer it to the fabric and cut it out. We sew all the parts together, sew a zipper into one of the side parts. Now you need to process the slices. The weight of the tent depends on the density of the fabric. The floor and back wall should be made of more durable fabrics, or several layers of used fabric can be used. Connect all panels with a double thick seam or linen seam so that the tent does not leak. Hem the ridge with braid, having washed it first so that it does not shrink. Lay a thin hemp rope between the ridge and the braid, and attach guy ropes to its ends, tied in loops. Cover the place where the loops are fastened with a special patch.
At the ends of the ridge, make holes for the poles on which your tent will be attached. Secure the slits with metal pins or process them with harsh threads. In the back wall, if desired, strengthen a hole with a sleeve for ventilation of the tent. At the entrance, make a fastening threshold that will protect the tent from moisture and dirt getting inside.

You can make waterproof fabric yourself using one of the following methods:

1. Place the fabric in a 40 percent solution of yellow laundry soap and, when it is soaked, take it out and dip it in a 20 percent solution copper sulfate. Then dry.
2. Mix a solution of lead acetate (30g per 1 liter of water) and a solution of aluminum sulfate (21g per 0.35 liter of water), shake and strain through muslin. Then put the fabric in this mixture for a quarter of an hour and dry without squeezing.
3. Place the fabric in a warm soapy solution (500g soap per 4 liters of water). Then squeeze it out and immerse it in a saturated alum solution. It is better to prepare a soap solution from 4.5 liters of ordinary soap solution, 25g of laundry soda and 450g of rosin powder.
4. Wet the fabric in a specially prepared solution (10 parts water, 4 parts alum, 2 parts fish glue and 1 part laundry soap). Then wring out the fabric and rinse it in a 4% solution of lead acetate.
5. Dip the fabric in a specially prepared solution (10 parts glue, 1 part acetic acid, 90 parts water, 1 part potassium dichromate), and then dry.
6. Place the fabric in a mixture formed from 500g of milk casein, 12g of slaked lime powder, 0.5 liters of water and a hot soap solution (25g per 3 liters of water). Soak it thoroughly, dry it and put it in a 2% solution of alumina acetate (12 parts alumina to 100 parts water). Remove and briefly place in almost boiling water to dry.

To prevent the tent from leaking, the panels are connected with a double thick seam, which is coated rubber glue. The ridge is hemmed with braid that has been pre-stretched to prevent shrinkage.

A thin hemp rope is passed between the ridge and the braid; guy ropes are attached to its ends, tied in loops. The place where the loop is attached is covered with a special patch. It is stitched along all edges and crosswise along with the material and the loop.

Design of the tent entrance fastener At the ends of the ridge, holes are made for the posts and secured with a light metal piston (eyelet) or covered with harsh threads. It is recommended to sew a cap over the grommet to protect the hole from water leakage.

They arrange in the back wall vent with a sleeve, which is especially convenient in winter. The entrance is made of two halves. The panels are fastened using fasteners and loops or a rope zipper. A fastened threshold is made at the entrance, which protects against water and dirt. The tent should be stored in a cover along with poles and pegs. Place it in a case completely dry, paying special attention to the drying of the corners and joints. various parts. At long-term storage tents, it is recommended to wipe the rubberized material with talc and roll it up loosely.