Installation of mosquito nets. Mosquito net installation. Installation of a mosquito net with plastic flags

When winter ends, a warm season comes, insects become active on the street, which, on purpose or not, tend to get into a person’s home. To do this, there is the easiest way - through a window or door. Therefore, it is natural that a person seeks to protect these "channels". And a modern solution in this vein is the use of so-called mosquito nets.

They allow you to keep windows and doors open so that fresh air can enter the room, but protect against insects.

Therefore, it is worth considering this invention in more detail, including the features of its installation.

About the article:

Kinds

• removable frame;
• sliding frame;
• pleated;
• roll type;
• with fastening on an adhesive tape or on a magnetic tape;
• "anti-cat";
• "anti-dust";

• for doors or windows.

Let's consider the main types in more detail.

"Antikoshka"

If there are pets at home, then when installing a mosquito net, their safety should also be considered. For this, there is a special model - "anti-cat". It is created from special durable threads, so that the product can withstand the most severe loads. Therefore, the same cat will not be able to tear or ruin the mesh. In addition, the product is equipped with an additional mount that improves safety. And it’s not worth removing such a grid even for the winter, its strength is enough to withstand such a fierce time. This will not degrade the quality.

Sliding

Suitable not only for ordinary windows, but also for terraces and balconies. Such a grid looks like two sliding parts that can open and close. In this case, the opening must have special guides for moving parts. And thanks to the gray color, visibility from the windows does not deteriorate.

Rolled

The most efficient solution. They look like a twisted roll in a box. It mounts above the window. An important advantage of this design is its versatility. After all, the mesh looks good and is convenient to use. There is nothing difficult in the installation of such a mosquito net. It does not require special care. And, of course, there were some drawbacks - the high cost.

"Anti-dust"

Today, allergies are a fairly common phenomenon among different segments of the population. Therefore, for such cases, it is worth thinking about yourself by installing an anti-dust grid. Such a product is created from a dense material that traps even the smallest particles. True, hence the disadvantage - rapid pollution. However, it is very easy to clean it. First, the surface is washed with a warm soapy solution, and then wiped with a soft, dry cloth.

Such a mosquito net does not impair the appearance of the window, while it transmits the sun's rays well. And its main drawback is the high price. And the rest is very worthy.

for doors

There are also such models. They not only protect the room from insects, but in a way play the role of a regulator of incoming air. Such products are installed on hinges. Fixation is done with magnets. A similar mosquito net on the door is a guarantee of the absence of a draft. Of course, if in other rooms this was taken care of.

Fastening

Speaking of mosquito nets, it is impossible not to touch upon the issue of their fastening. And it can be like this:

• using ears;
• on hinges;
• on plunger pins;
• on z-shaped fasteners.

The latter option is the most successful in terms of reliability and ease of use. It does not require additional holes to be made in the frame. This mount can be used for both wooden and plastic windows. The only drawback is the tightness of the mesh. Due to the remaining small gaps, especially dodgy insects can still penetrate into the room.

The pins are screwed into the window frame. Therefore, the fastening is reliable. The elements are made of stainless steel. This solution allows the mesh to fit snugly against the frame, and it is also easy to install and dismantle it.

Hinged fastening is good to use for doors. In this case, a reinforced profile is used, because the load on the frame is greater.

What mount to choose?

It all depends on the location where the installation will be performed. For a plastic window, you will need four fasteners and eight self-tapping screws.

To remove the screen from the window, take the plastic holders with both hands, and gently pull them up. First, the mesh will come out of the lower holders, then it should be bent, and then removed from the upper ones. After that, the grid remains to be taken into the room.

As you can see, there is nothing difficult in installing and dismantling a mosquito net, even if a plastic window is used. Therefore, in most cases, it makes no sense to turn to specialists to perform such procedures - your knowledge and skills should be enough.

Now it is impossible to imagine plastic windows without mosquito nets. In the summer, protection is indispensable, since insects (mosquitoes, midges and flies) strive to enter the home. In addition, the mosquito net serves as protection against dust, debris and fluff entering the room. You can order a mosquito net complete with windows and install it immediately after installing window blocks or purchase it separately.

The classic version of the mosquito net is made of an aluminum profile, on which the mesh fabric is stretched. As a standard, mosquito nets for windows are made of a gray shade of fine mesh to protect our homes from the penetration of annoying mosquitoes and flies. In the last century, when no one knew about metal-plastic windows, there were no mosquito nets either. In those days, people hung gauze or mesh on the windows. If it was very hot outside, in order to sleep peacefully at night and not worry that mosquitoes could bite all family members, the windows were opened, and the free opening was hung with a thin curtain. Naturally, such protection did not work and the insects still flew into the premises.

Now you can forget about the buzzing of mosquitoes and sleepless nights and order special plastic mosquito nets.

The main task of the nets is to provide reliable protection of housing from the penetration of flies, mosquitoes and midges. In addition, the mesh traps dust, debris and small particles that can cause allergies. If you install mosquito nets on windows and doors, then you can not worry about your safety and the safety of your pets. Let's say you live on the 5th floor or higher, you want to open the window wide open to ventilate the rooms, but you cannot afford such a luxury, because your beloved cat may fall out of the window. With a mosquito net, this can be avoided.

In addition to the listed advantages of protective nets, there is another important plus - ease of care. Twice a year, the nets are cleaned of dust and dirt with a soft sponge and soapy water. After half an hour, we put the grid in its original place.

Types of protective products

The cost, method of attachment and configuration of mosquito nets may vary. Consider the main types of protection:

• on a framework from a strong frame, a removable design;
• sliding structure on the frame;
• roll;
• fastening on a magnetic tape or adhesive tape;
• a product with an applied composition that protects the home from dust;
• durable mesh - protection from the claws of pets.

Consider the popular types of mosquito nets used for installation on windows and doors.

If you have pets at home (a dog or a cat), then you also need to take care of the safety of your pets. You can order a protective net with the funny name "Antikoshka". It is made of durable material, so the mesh is able to withstand heavy loads. If the animal tries to break the mesh with its claws, nothing will work. The mosquito net will remain just as strong. The pet will not be able to spoil the protection or break it. For safety, this mesh model has a strong mount, so you can not remove it for the winter.

Sliding mosquito net is suitable for installation on balconies and terraces. Consists of 2 sliding halves that open and close with pressure. In order for the grids to function correctly, it is necessary to install guides, they serve to adjust and move the halves. The color of the mesh fabric is standard, gray. By the way, mosquito nets of any kind are made of gray canvas. This color does not impair visibility and does not affect vision.

A mosquito net with magnets is a convenient solution. This model is considered universal, since you can order a mesh of any size to install in the country, take it with you on vacation or provide protection in a home where windows of non-standard sizes are installed. Among the advantages of this type of mesh, it is worth noting the ease of installation - it is necessary to remove the protective tape and attach the mesh to the metal-plastic window. Due to the magnetic tape, it will firmly adhere to the frame. There is a second option for window protection, but instead of a tape with a magnet, the mesh is equipped with adhesive tape (like double-sided tape).

Among the shortcomings of the mosquito net in rolls, it is worth noting the fragility. In addition, such a design cannot be called durable.

The classic version is a mesh stretched over a durable plastic frame. Can be made from standard fine mesh, pet claw resistant and dust resistant coated. Mosquito net is installed on both doors and windows.

The anti-dust mesh version is made from a very fine mesh fabric that is capable of trapping large dust particles. This is the main advantage of the mosquito net, the disadvantage is that it is difficult to maintain. Since the product retains dust, it is necessary to clean the canvas frequently. To do this, it is necessary to remove the structure, rinse with a stream of warm water, then apply a soapy solution, wait 5-7 minutes and rinse again with warm water. After water procedures, the mesh must be thoroughly wiped with a soft cloth (not damp) to check how effectively the cells have been cleaned of dust. Despite the rapid contamination, the mesh transmits light well. The cost of such protection will be 2 times higher than the price of a conventional mosquito net.

Mosquito net attachment

Depending on the selected type of mesh, the mount may be different:

• fastening "ears";
• loops;
• plunger pins;
• fasteners "z-shaped".

A popular and commonly used mosquito net fastener is the z-shaped fastener. It will be easier and more reliable to carry out installation with the help of such fasteners. It is important that you do not need to make holes in the metal-plastic frame. In addition, the grid can be installed not only on plastic windows, but also on wooden frames. Of the shortcomings, only one should be noted, such a mosquito net holder does not provide a snug fit to the frame, so small insects can still squeeze through a small hole.

A reliable mounting option is the use of pins. They are screwed into the window frame, so the mesh fits snugly and insects cannot enter the home. Ease of installation and reliability of fastening - this is worth paying attention to. It is also important that the mesh can be easily dismantled for the winter or in order to be washed from dirt.

Hinge mounting is best chosen when you need to install a mesh on the door. Then it is advisable to order a durable profile with an additional jumper so that the structure does not sag under its own weight over the years of operation.

How to install a mosquito net

When ordering mosquito nets for windows, you receive your order with the necessary set of fasteners. When taking measurements, it is necessary to discuss the issue of fastening, so that the manufacturer produces mosquito nets and provides a complete set of fasteners. If you deal with these issues yourself, then you need to familiarize yourself with some of the nuances in order to correctly take measurements.

What you need to know:

1. Open the window. Take a construction tape measure and measure the free opening first horizontally (a), then vertically (c). Record your measurements on a piece of paper.
2. Further, depending on the type of fastening chosen, you will need to add a few millimeters to the resulting figure.

If you want to work with a zigzag fastener (“z”), you need to add 5 cm to the resulting measurement figure for width and height (a and b). This will give us a net measurement of height and width. Fasteners are needed 2 each: lower and upper, plus 8 more screws (size 3.2 x 16).

If you want to install mosquito nets on windows on brackets, then you need to add 5 cm to the received figure "a" (width), + 18 mm to the height measurements.

When mounting grids on pins, add 2 mm to the measurements on each side.

Attention, if there are protrusions in the window opening that may interfere with the installation of the mesh, it is necessary to notify the manager about this when ordering. It is also advisable to take a picture of the window and tell the experts exactly how you took the measurements in order to avoid annoying misunderstandings when receiving an order and installing it yourself.

After you have chosen the method of attaching the mesh, you need to prepare the tools. An electric drill may come in handy if you need to drill holes for the hinges.

Features of installation of mosquito nets:

1. We make markings for fasteners. For a window of standard sizes, 4 elements can be distinguished, for large windows - 8.
2. After the planned marking with a drill, we drill holes in the frame of the mosquito net.
3. We attach the fasteners to the frame, screw in the screws, check our work.
4. Now you need to make 2 more markings for attaching the holders. We take measurements vertically, divide the resulting figure in half - this will be the attachment point.
5. We screw the holders into the plastic mesh frame with screws, check the strength. The material can be different: plastic or metal. If you chose the first option, then it is advisable to handle the holders very carefully, as they break quickly.

How to insert a mosquito net

Many people who decide to install the nets on their own are wondering: “How to put a mosquito net” on the window. This work is not difficult, the main thing is to be careful not to accidentally drop the grid on the ground.

It is necessary to turn the fastener (“lugs” or holders) to the “away from you” position in order to put the net. Now take the grid by the holders and carefully pull the grid out of the window, now bring it back, insert it into the lower part and fix it from above. With one hand, hold the net by the holder, with the other hand, try to turn the fasteners to fix the frame. That's all, you have successfully completed the job, now you can enjoy fresh air without fear that insects will bother you.

We examined the external method of attaching mosquito nets to windows. There is another method that can be used for mounting protective structures - this is internal fastening.

The grid is mounted in a slightly different way:

• holes must be drilled around the perimeter of the window opening;
• then we fix the fasteners;
• install handles in the middle of the mosquito net;
• we take the grid by the holders, we start the grid first from above by the window in order to install the lower part of the grid into the grooves;
• then lower the canvas and align in the opening.

At first glance, installation may seem like a difficult task to you, but if you delve into the intricacies of installing a mosquito net, then you will enjoy the work done with your own hands. Just remember that regardless of the chosen method of fastening, the mesh is not designed for strong mechanical pressure, so you do not need to let your pets and children close to the wide open windows.

How to remove the grid

For winter, it is best to remove mosquito nets from windows to protect them from harsh weather conditions. If it is not possible to remove the screens so that they are not damaged indoors, then they can be left on the windows. Nothing terrible will happen to the nets, only the service life of the products will be reduced.

To remove the nets, you must do the opposite: first unscrew the ears or brackets to the sides (do not forget to hold the product with one hand on the holder). Then take the mesh out, unfold it and bring it into the room. Do this job very carefully so as not to let the net fall to the ground.

You can and should take care of the nets. At the end of the summer season, when it is already cool outside, the protection can be removed and washed. You can simply wipe the product with a damp sponge to remove dust, fluff and dry insects, but it is best to take the nets to the bathroom and wash thoroughly with warm water and detergent. It is not necessary to rub the canvas strongly, it is enough to walk with a damp sponge over the surface to remove dirt, then apply a soapy solution, wait a few minutes and rinse with water. Such manipulation must be done at least 2 times a year.

Mosquito net installation. Video:

In any region, they try to protect living quarters from insects from the street, whether they are flocks of mosquitoes or single individuals. The most environmentally friendly and safest method of protection is mechanical - equipping window and door openings with mesh structures, permanently placed or removable, compactly folding or rigid - in the form of frame sashes of a certain size.

Types of devices to protect housing from mosquitoes

To know how to install a mosquito net - a necessary accessory for window casing, let's take a closer look at the most common designs of these protective devices and their characteristics.

The main task of such nets is to create a barrier on the way of insects from the street to the apartment. Based on this, window and door openings of housing for protection against mosquitoes used to be equipped with any mesh material that was suitable at first glance - gauze, tulle, gauze, steel fine-mesh construction mesh, etc. However, it soon became clear that, due to certain factors, these materials lose their functionality and require repair or replacement.

Some features of mosquito net devices

To choose the right canvas for mosquito protection, we list the necessary characteristics that it must have:

• the optimal combination of mesh size and thickness of the base material - creating a barrier to the path of insects with unhindered passage of air and maintaining transparency sufficient for viewing;
• strength - the ability to withstand random mechanical stress and wind;
• moisture and heat resistance, resistance to ultraviolet - the preservation of the strength characteristics and geometry of the canvas by the material under the influence of atmospheric moisture, summer air temperature and sunlight;
• antistatic properties - to prevent clogging of the openings of the cells with dust attracted by static electricity;
• ease of daily care to maintain the necessary sanitary and hygienic condition;
• safety - no harmful emissions into the air.

Based on the above requirements, far from all mesh materials are suitable for durable and effective equipment of window and door openings with insect protection: gauze quickly becomes dirty, stretches and impairs visibility, uncoated steel wire meshes rust, and fine-mesh nylon ones accumulate static electricity and clog dust. These materials can only be used as a temporary solution to the problem, and for high-quality housing with mosquito protection, special fine-mesh mesh canvases are used.

Types of mesh for mosquito devices

Mosquito repellent mesh canvas has certain characteristics.

The first one is cell size , which is in the range of 0.5 - 1.2 mm. With a decrease in the lumen of the cell, the protective ability of the mesh increases - less dust will penetrate into the room. But it should be borne in mind that the canvas with the smallest cells needs to be washed more often - as it gets dirty, its permeability to air and light quickly deteriorates. A canvas with a maximum cell size is almost no barrier to dust. Therefore, the best option when choosing the degree of protection would be a mesh with a medium-sized cell - from 0.8 to 1 mm.

The second most important characteristic of the mesh fabric, tied to the size of the cell - production material from which the canvas is made:

• cotton - with high resistance to ultraviolet radiation and retention (lint on threads), cotton mesh is rarely used to protect against mosquitoes from the outside, since the lack of resistance to moisture and mold causes its fragility;
• polyester (nylon) - in the absence of any outstanding individual characteristics, a canvas made of a thread up to 0.8 mm thick, which can withstand a weight of up to 4 kg, is strong enough, durable, cheap and therefore most common for outdoor protection against mosquitoes;

Fine-mesh anti-mosquito fabrics: on the left - made of cotton, on the right - made of polyester.

• nylon - a polymer for the production of an anti-allergic mesh of complex fine-mesh weaving "anti-dust", which even retains pollen from flowers;
• steel thread - a fabric woven from steel wire is widespread due to its high strength, but the price of a material with a protective zinc coating or stainless steel is quite high;

Mesh material: on the left - "anti-dust", on the right - "anti-cat" made of stainless steel

• fiberglass (PVC-coated fiberglass) is the best choice due to its high transparency and strength of the canvas, which is flame retardant and resistant to all atmospheric factors.

An important factor when choosing a grid is also its color , affecting light transmission, transparency and compliance with the interior. The most transparent for viewing is a gray canvas, but if the window is not panoramic, this factor can be sacrificed in favor of the aesthetics of the canvas and choose a grid of a different color.

Colored mesh sheets for mosquito protection

If there are pets in the house, it is of particular importance strength cellular canvas, which must withstand the impact of claws, teeth or the weight of pets. Grids that can withstand these factors are combined into group "antikoshka" and are produced from polyester, fiberglass and metal (steel woven and aluminum perforated).

Types of metal meshes of the "anti-cat" class: 1 - woven steel, 2, 3 - aluminum perforated.

The strength of cellular canvases of this class allows them to be used for mosquito control devices installed both on large windows and on doorways.

Of the products offered on the modern market, mosquito nets from such foreign manufacturers as the German Roto (Roto Frank AG), the Danish Velux (Velux Group), the Polish Fakro (Fakro Group) and the American Pfeiffer ( Phifer & Company).

Designs of mesh devices for protection against mosquitoes

Mechanical protective mosquito devices are produced today in many varieties, the difference between which from each other is often not even noticeable visually. But there are two main groups of such devices:

1. frame (frame);
2. frameless.

Frame represent a frame of a fixed size and format, on which a mesh fabric is fixed. Such a sash can be installed on a window or door block in the opening using the following devices:

• plungers (pins on springs);
• loops;
• Z-mounts;
• corner clamps;
• rotary flag clamps;
• guide rails.

Frameless designs anti-mosquito devices include the following types:

• on sticky mounting tape;
• roll (roll);
• pleated.

If you have elementary installation skills, all types of protective devices are possible for self-installation, just the installation of each of them is carried out taking into account the individual nuances of the design.

Methods for installing mosquito devices and the necessary fittings

Consider how on one's own install a mosquito net on a plastic window if the protective device is ready or semi-ready (mesh canvas with Velcro).

Installing the mosquito sash in the window block on the plungers

Plungers are a system of movable pins (rods) with closer springs installed along the perimeter of the sash at its end and holding the frame with the mesh in the window opening by resting against the inner edge.

Important! With the plunger method of fastening, the frame with the mesh is not installed overlay on the window block, but in the opening between the sealing rubber bands, so the accuracy of measurements of the future frame is especially important - the distance between opposite points between the seal is measured in several places and the average value is taken as design. Measurements, as a rule, are carried out by the manufacturer of the protection.

Of all the ways to install mosquito protection, plunger is the most reliable and therefore expensive, but still affordable mounting option.

The manufacturer installs 4 plungers on the protection frame - 2 on each side. Having placed the frame in the window opening at the place of installation, the drilling points for installing mating sleeves are marked with a marker on the pins. Having drilled 2 holes on one side and installed the sleeves in them, the frame rods are installed in the nests, and the pins rest against the window block on the other side. Once again checking the correct location of the applied risks, the remaining two holes are made.

A brush seal is glued along the outer contour of the sash with a mesh - to fill the gaps between the window unit and the mosquito protection sash.

Locations of spacer plungers and sealing brushes

After installing the remaining mating sleeves, the frame with the mesh is installed in place, bursting with plungers in the nests.

Installation of protection against mosquitoes in the window opening on the hinges

Window sashes, as a rule, open inward, so the frame with the mosquito net is installed on the window block from the outside - overlaid with self-tapping screws.

Hinges are installed on the protection frame in such a way that their supporting half remains removable downwards when the pins are directed upwards.

Important! If the floor of the apartment is the first floor, then the hinges on the sash can be installed so that the axes of their supporting halves are located towards each other or directed in opposite directions - with such an attachment, the frame from the side of the street can be removed only by unscrewing the screws.

Fittings for hinged sash installation: hinges, lock (magnetic and latch)

Having fixed the latch and hinges on the frame with screws, the sash is applied to the window block and centered, after which their axial halves and the lock are fixed with screws on the binding - it is more convenient to perform this operation together and with the help of an electric screwdriver.

Mounting on hinges and locks

The hinged installation of mosquito protection is indispensable when equipping doorways with a mesh, but it is better to install 3 hinges on the sash.

Mounting the frame with protective mesh on the Z-brackets

For this method of mounting the sash with a grid, metal fasteners of a Z-shaped configuration are used, and the elements of the upper location differ from the lower brackets in the size of the pressure shelf.

Z-brackets and their location on the window unit

This method of fastening the frame mosquito protection is also quite reliable, but the location of the latches must be precisely adjusted to the height. In addition, additional spacers sometimes have to be glued to the brackets for a tighter fit of the sash to the block.

The installation begins with fixing the lower clamps with self-tapping screws at a distance of 25 mm from the lower edge of the window opening. Then, from the brackets, the height of the frame is laid upwards and another 12-15 mm are added to the risks, after which the upper Z-elements are mounted, which, for aesthetics, should be located strictly opposite the lower ones.

Z-clamps: lower and upper (with technological clearance)

As can be seen from the figures illustrating the plunger and two subsequent methods of installing mosquito sashes, the dimensions of the protective frames of the rod fixation with the same dimensions of the window opening will differ downwards, which must be taken into account if a decision is suddenly made to change the mounting option.

Binding the size of the mesh sash to the dimensions of the opening, depending on the method of installing protection

Fixing the frame protection to the corner stops

This mounting method is a variation of the previous one and differs from it in the location of the brackets and, accordingly, in their design.

Mounting the mosquito frame on the corners - "pockets"

Corner stops, also called pockets, are by definition mounted at the junction of the corners of the protective frame to the window unit, while the elements of the upper row differ from the lower latches. Location measurements are made identical to the layout of the Z-brackets.

The location of the top and bottom row of "pockets"

Mounting the frame on "pockets" is a reliable fixation technology and even has an advantage over mounting on Z-brackets - the protection frame cannot be moved to the side by a gust of wind.

Anti-mosquito frame with flag clips

The essence of the method of fixation is the use of swivel brackets, the durability of which depends on their design and material of manufacture.

The sash, equipped for convenience with a crossbar or handles, is located outside the window block. After setting the frame in place, the flags turn outward beyond the contour and press the frame profile to the binding.

Metal version of flag clamps

Fastening the flags to the frame is not difficult - with self-tapping screws along the perimeter of the sash with a step depending on the size of the opening and the wind load on the window.

Plastic version of rotary flags

This method of fastening is inferior in reliability to the previous ones, since the landing of the flags on the sash and the density of fixing the frame weaken over time, and therefore the brackets require periodic tightening of the self-tapping screws.

Mounting the protective sash with mesh on the guide rails

Currently, plastic window blocks are produced, the design of which provides for a movable sash with a mesh that moves in the opening along guides located outside or inside and which are part of the profile. But such window covers are much more expensive than usual ones, so it is more expedient to equip the window with a sliding frame on your own.

Window blocks from a profile designed for industrial fitting with mosquito-proof sashes

To equip a window with a sliding sash, you must order the frame itself with a grid and guides. The height of the protection frame is taken in such a way that there is space left on the horizontal sections of the window block above and below for mounting the skids, and the width depends on the size of the opening.

The guides can be made of aluminum or plastic and, depending on preference, are attached to the block from the outside or from the inside.

Important! The slats are installed at a distance between them, providing a gap with the sash from above of 1-2 mm for free movement of the frame at any time of the year, and strictly parallel to each other.

Samples of installed mosquito protection sliding doors

For easy sliding, the sash is equipped with rollers at the bottom, sliders at the top, and the contour of its junction with the guide is finished with a brush seal on the back side.

Using a tape measure and a building level, the installation of guides is marked, after which they are fastened with self-tapping screws. Roller fittings and handles are installed on the sash for ease of movement, after which the protection assembly is inserted into the skids. If the frame after installation easily moves and adjoins the block well, then restrictive plugs are attached to the ends of the rails.

The idea of ​​​​sliding doors will be more complete if you watch this video:

Installation of frameless mosquito net protection on adhesive tape

Of all the existing ways to protect housing from insects and dust, this method is the simplest.

The principle of fastening a protective mesh into a window opening without a frame

Velcro tape is purchased with a length equal to the perimeter of the window opening, and a mesh canvas with the necessary characteristics for the size of the window block with a margin of 3-5 cm in both directions.

Ready-made protection kits of a certain size are also sold, including canvas, Velcro and glue.

Components are available in various colors so that the mounted device fits optimally into the interior of the room.

Set for mounting mosquito protection on Velcro tape

Velcro is attached to the profile of the block from the inside with glue - after preparing the base (degreasing and marking along the ruler). It is better to attach the tape to the canvas on a sewing machine, having previously tucked the edges of the mesh inward.

The technology is simple, functional, cheap and safe.

Roll (rollet) design of the protective device against mosquitoes

This type of device is the most modern both in technical design and visually, which causes its high cost - from 5 thousand rubles. per square meter.

The design consists of a horizontally mounted cylindrical box, in which a leaf is placed on an axis with a return spring, which extends along guides with brush seals to the required length, if you pull the handle located outside.

External view and internal arrangement of roll mosquito protection

Roller blinds are manufactured in industrial conditions, while there are restrictions on dimensions: in height - up to 250 cm, in width - up to 200 cm.

Important! With many advantages, this design has a serious drawback - only an ordinary mesh can be installed in it, and “anti-dust”, “anti-pollen” and “anti-cat” canvases cannot be used.

Roller insect protection: on the left - at the installation stage, on the right - installed in place.

Pleated mosquito net

This type of protection is a novelty in the domestic market. Each device is produced for a specific size of the window opening, while the maximum dimensions are limited to 5 meters in width and 3 meters in height, which makes it possible to equip them with public, administrative or sports premises with large glazing.

Schemes of the possible movement of the canvas, depending on the design of the protection

The principle of operation of the device is to cover the opening with a mesh folded in the shape of an "accordion" in the vertical or horizontal direction (depending on the design).

The constructive solution of the device imposes restrictions on the material of the canvas - in the protection of the "pleated" polyamide canvas is used, the characteristics of which, however, are quite high.

Types of cellular canvas to protect the "pleated"

Advantages of the "pleated" device:

• the possibility of servicing large openings;
• high degree of compactness when folded;
• durability;
• a wide choice of colors.

Type of protection "pleated" in working order

Despite the apparent complexity of the internal structure, the “pleated” is quite possible for self-installation, since in the assembled state it is a rectangular block, ready for installation on the window frame.

Installation diagram of one of the types of mosquito protection of the "pleated" type from the domestic manufacturer "SK-F" (SKF).

In addition to high technical and aesthetic characteristics, "pleated" stands out among other types of protection and the price - from 8 thousand rubles. for 1 square meter.

Watching this video will help you mount the "pleated" protection yourself:

Conclusion

In most regions of Russia, mosquito protection for door and window openings is a necessary accessory. Based on this, domestic and foreign manufacturers offer these products in a wide range of prices that can satisfy the consumer even with low purchasing power. Therefore, giving priority to functionality, you can protect your home from insects and dust for a very small amount.

The main essence of the article

1. The most environmentally friendly and safe protection against mosquitoes are mechanical (enclosing) means, so mesh canvases are widely demanded to solve this problem.
2. Mosquito and dust protection needs not only housing, but also most premises of any other purpose, therefore, mosquito protection manufacturers offer devices of various functionality and performance class.
3. Despite the varying degrees of complexity of mosquito protective devices, the vast majority of them are suitable for do-it-yourself installation.
4. Ready-to-install products of industrial production have an installation instruction, the observance of which guarantees the efficiency and durability of the device. If the accessory is made independently or in a small craft workshop, then you need to know some of the nuances of its installation, characteristic of this design.
5. Following the recommendations of professionals will protect against damage to the material and provide long-term and effective protection of the premises from dust and insects.

Hide

Summer brings not only positive emotions and relaxation, because you should not forget about annoying flies and dangerous mosquitoes that strive to fly into the open window. A mosquito net is inexpensive, but if you count that there are several windows in the house, then in the end you get quite a decent amount, which, if desired, can be saved. Do-it-yourself mosquito net is done quickly and will be inexpensive.

Which is better - a purchased mesh or made by yourself?

Buying a window mesh will cost you about 1500-2000 rubles, so for the sake of savings, you can make it yourself. Many people ask the question - how to make a mosquito net on a window? It is not difficult, especially since everything you need can be bought at a hardware store. If you are interested in the question of what mosquito nets are made of, then the answer is simple - the material is durable fiberglass with the addition of weatherproof PVC. The higher the quality of the material, the higher the protection against insects.

Before you make a mosquito net with your own hands, take careful measurements, do not forget about allowances. If you are going to attach the mesh with Velcro or glue, choose something that can be easily removed without damaging the window.

A few simple ways to make a mosquito net with your own hands

There are two types of mosquito nets that you can make yourself:

1. Fastened with fastening tape - an easy and cheap way to make a mosquito net with your own hands.
2. Framework.
3. Roll.

One of the easiest ways to make a mosquito net with your own hands is with the help of special material and adhesive tape.

Take high-quality Velcro, the quality of attaching the protective mesh to the window opening will depend on this. You will also need special material with small cells. The smaller the cells, the better. Such material can be purchased at fabric stores, or you can use old products, for example, unnecessary tulle. It is best to purchase a special mosquito net - it reliably protects against insects and withstands atmospheric influences.

Mosquito net fixed with adhesive tape

After all measurements are taken, take the material and cut it, do not forget to leave small allowances. Velcro divide into two equal parts. Apply glue to one part and carefully glue it to the window opening. After the glue has dried, attach the mosquito net to the adhesive tape. Similar grids can be made for a car. It is done quickly and easily, at minimal cost. Instead of sticky tape, special magnets can be used, this will significantly reduce the installation time of the grid and simplify the process.

Frame window grids

A more costly and complex method of manufacturing a mosquito net is a frame-mounted method. To do this, you will need metal corners, plastic cable and rivets.

The first thing to do is to measure the window from the outside, because that is where the mosquito net will be attached. On the cable, cut the desired length, adhering to the angle of 45 degrees. Sand the slices and connect with metal corners. Now make holes in the corners in which the rivets will be located. They should be outside, not inside the cord. Now it remains to fix the mosquito net itself on the frame. Do not pull the mosquito net too tightly, as this can deform or tear the canvas.

Frame window grids

You can make sliding mosquito nets with your own hands, they will fit well and protect the balcony opening or front door. A mosquito net on the balcony will help you prevent the penetration of dangerous insects into the room, it will reliably protect even from street dust. The manufacturing technology is the same, the only difference is that the material is cut in the middle, the edges are processed. For convenience, you can attach magnets or rivets to the edges of the mesh, so you provide additional protection.

Roll mosquito net

Rolled mesh window operates on the principle of roller shutters. It will reliably protect against insects, and it is convenient and easy to use. If you are interested in how to assemble a rolled mosquito net with your own hands, then there is nothing complicated here. You just need to be patient and have the right materials.

With your own hands, you can make a mosquito net for a window of any size. To make a rolled protective mesh, you only need a special box with a shaft and material. To attach the mesh to the window, use special magnetic latches. You can apply fastening with screws with an overlap or at the end of the guide in the opening to the slope. It is more convenient to use a rolled mesh than a regular one, and it is much easier to care for it.

Roll mosquito net

Rolled mosquito net on the window is an excellent protection against annoying insects. Allergy sufferers will especially appreciate this design - after all, it will protect the room not only from mosquitoes, but also from plant pollen and poplar fluff. The material for such a mesh is best to choose fine-grained, this will increase the level of protection.

Making a mosquito net with your own hands is not difficult. If you need a mosquito net for a balcony or window, you can make it yourself quickly and at no extra cost. Give this process a few hours and enjoy a quiet life without annoying insects! A handmade mosquito net is quite inexpensive. After the summer, it can be removed from the window and carefully packed, and next year it can be hung again on the window.

Homemade and the cheapest option for making a mosquito net without using a frame. This option is a mesh fastening directly to the plastic window profile.

The order of installation of the mosquito net is determined by its design. The complexity of installation depends on the location, method of fixing and features of the window or door.

Tools used:

• Screwdriver or drill;
• Thin drills;
• riveting tool;
• Screwdrivers;
• Line, roulette.

The mesh package usually includes fasteners, which is discussed when ordering and checked before purchasing the product.

Fastening to internal metal brackets is a simple and safe way to fix a removable frame mesh on. Hooks are mounted on long slats with aluminum rivets. Installing the mesh in the opening is performed as follows:

1. Using the side handles to hold the product, the top brackets are wound behind the window influx.
2. The grid rises all the way up, the lower hooks are hooked on the frame ledge.
3. The mosquito cloth is planted down to the end and aligned in the window opening.

The external version of fixing the mosquito net is a reliable method that does not damage the rubber seals, but it is dangerous because you have to stick out to screw the corners.

Mounting order:

1. The bottom brackets are fixed with self-tapping screws, placing them at a distance of 20 mm from the edge of the opening.
2. The height of the grid is measured, 10-15 mm is added, the mounting points of the upper brackets are marked.
3. The corners are screwed at an equidistant distance between themselves and from the borders of the window opening.
4. A mosquito net is installed: slipping it all the way into the upper fastener and leading it into the lower corners, the product falls into place.

Installation using plungers is used if the mosquito net cannot be fixed to standard brackets. For example, when closely spaced guards get in the way or there is not enough space on the frame to accommodate z-brackets. Plunger mosquito nets are not placed overlapping, but inside the window opening. Therefore, their dimensions must exactly match the perimeter of the frame.

Mounting on plungers:

1. Places for pins are prepared in the grid frame: first, four holes are drilled with a diameter, like that of the threaded part of the plunger, then the holes in the outer walls of the profile are expanded to the size of the retractable tip.
2. Pins with springs on are inserted into the frame and tightened with tips.
3. The grid is tried on in the opening, marks are placed opposite the plunger outlets.
4. Holes are drilled into which mating pin sleeves are installed.
5. A brush seal is glued onto the mesh profile.
6. One side of the product is placed by plungers in the reciprocal holes.
7. Squeezing two tips from the opposite side, the mesh is inserted into the opening and fixed.​

Anti-mosquito structures of swing type are installed on hinged hinges, taking into account certain features:

• The doorway should be blocked by 10 mm on each side.
• The minimum gap between the frame and the upper slope is 21 mm.
• Sufficient space is provided around the self-closing mechanism for its adjustment.
• The magnetic latch is attached to the opening, and the striker is attached to the frame profile.
• The number of magnetic latches is selected based on the height of the door.

Roller mosquito nets can be mounted on the window frame or in the opening. Assembly of the structure is carried out according to the instructions of the manufacturers. The process is divided into stages:

1. Cutting the body and shaft with a mesh to the required dimensions.
2. Preparation of guides and fixing strips.
3. Assembly of parts of the body and gearbox.
4. Marking and execution of mounting holes.
5. Fixing the system to the window frame.
6. Operation check and adjustment.

It will be a simple matter to install a conventional frame or. More difficult, but also affordable to do it yourself, will be the installation of a rolling mosquito system.