Installation of doors on Finnish hinges. Instructions for installation and operation of the Jeld-Wen entrance door. Are Finnish products really environmentally friendly?

Door block is not load-bearing building element, therefore, loads from building structures should not be transferred to it. Leave a gap of at least 5 mm between the frame and the building structure.

INSTALLATION PROCEDURE

1. Unpack the door frame.
2. On a flat surface that prevents damage to the product, assemble the elements of the box, choosing the desired side for opening the canvas. Check that the edges of the crossbar and the pillars are in the same plane, and at the place of their contact the gap does not exceed 1 mm. On back side Drill four through holes into the crossbars, then connect the frame elements with self-tapping screws. For a self-tapping screw 4.2 x 70 we recommend a drill with a diameter of 3.5 mm.
3. Insert the frame into the doorway and secure with wedges (at least three points on each side).
4. Using a level, secure the hinge post strictly vertically using a hammer drill and mounting screws, using spacers between the opening and the frame at the fastening points.
5. Loosen the hinge fastening screw and hang the door leaf.
6. Close the blade, and install the stand on the side of the lock so that the blade fits along the entire perimeter, providing an even gap, and secure the stand in this position.
7. Open and close the blade several times, making sure that it is installed correctly and that nothing interferes with closing. Right installed door(when opened at 45°) should not open or close spontaneously.
8. Finally secure the hinges to the screws and install the fittings.
9. Fill the installation gap between the box and the wall with low-expanding polyurethane foam (when using foam, follow the manufacturer's instructions).
10. It is recommended to install the platband only after completely dry polyurethane foam. During the drying period of the foam (about 12 hours), the door should be kept closed at all times.

CHANGING THE SIDE OF THE CANVAS

A blind canvas of standard height is available for both right and left. This is achieved due to the vertical symmetry of the canvas.

To change the door opening direction:

• unscrew the fastening screws and pull the lock body out of the door, turn it 180° (so that the lock tongue is on top, above the bolt), install the lock back in this position;
• Using pliers, pull the bolt out of the lock body by 3 mm and turn it 180°.

Tools required for installation: screwdriver with a set of bits, hammer drill or impact drill, level, wood saw, measuring tape.

Manufacturers use a special technology that has been developed and improved over many years. Now these are automated lines where constant quality control takes place at all levels of production:

1. when selecting material;
2. packaging;
3. transportation.

We can say with absolute certainty that Finnish interior doors are entirely products European level. Many canvases white - distinctive feature manufacturers. However, for Russians the ratio of quality and cost is important. For many, this is the determining factor, so white Finnish doors win in all respects. The price is lower for those canvases where honeycomb filler is used as an internal filler, since it significantly lightens the weight of the structure.

Due to the fact that Finnish interior models have a strict and clear design, where every detail is in its place, and cool shade, they are increasingly chosen for offices, apartments and houses, where owners want to simplify the situation and leave only the essentials. This style is called high-tech.

Our doors have certificates that confirm their level of quality and characteristics. On products from Finland, a manufacturer’s stamp is placed on the end of the canvas - this is one of important requirements to enterprises of this level.

Features of Finnish doors

Finnish whites interior designs(office, smooth, paneled) are produced on advanced high-tech equipment; environmentally friendly materials and high-quality fittings are used in their production. At each stage of creation there is strict control. Thanks to this, the products have high quality that meets international standards.

Smooth Finnish doors will fit perfectly into modern interiors: public, office, residential and industrial. Their discreet and at the same time elegant appearance will be a universal solution.

Follow the instructions, be precise with measurements and check the results. Please read the instructions carefully before proceeding with installation. The external door is intended primarily for use as front door in private houses for year-round use, mansions and townhouses, in buildings where thermal insulation qualities are required.

It is strictly forbidden to install doors in a house under construction or in a room where wet work is being carried out (for example, concreting a floor, pouring screed, etc.). Excessive moisture can cause wood to warp and paint to peel. In addition, the fittings, including the lock body, may become rusty.

ATTENTION! When installing entrance doors in the cold season, you must use certified mounting foams, specifically designed for use with low temperatures- information with specific recommendations for use is usually printed on the cylinder by the manufacturer.

Always install moisture barrier (bitumen strip, etc.) between the horizontal base and the threshold.

Never install the box directly on a concrete floor or screed! Use, for example, bitumen strip, etc.

Doors should be installed in places with a sufficiently long roof overhang or canopy over the door, which will protect the door surface from moisture and sunlight.

When determining the size of the canopy, you should be guided by the following formula: the width of the canopy D must be at least half of the height of the canopy (the distance from the bottom of the door to the bottom of the canopy, see diagram).

Entrance door installation steps:

Stage 1

Check that the base under the threshold is horizontal.

Install the ebb in the mounting opening and place the assembled box on it

Coat the seam with sealing compound.

Low tide can be installed later. In this case, bring the ebb tide under the threshold

and glue it, installing the ebb in the groove intended for it in the threshold.

Stage 2

Secure the box in the mounting opening using wedges, inserting them above the box's mounting holes so that the side of the box with hinges is exactly vertical (both parallel and prependicular to the wall plane). Use two wedges for each mounting hole in the box, insert one wedge from the outside, the other from the inside. Use a spirit level to check that the box is level.

Make sure there is enough space around the perimeter of the box for the seal

and secure the hinge side of the box to the wall with mounting screws.

Stage 3

Install anti-burglary pins in the door. Do not screw them all the way in, leave a margin of 10mm. Hang the door leaf on its hinges.

Tighten the anti-burglary pins until they are tight, install and tighten the hinge mounting screws.

Stage 4

Make sure the threshold is set horizontally. Align the side of the box with the lock strike plate exactly (both parallel and prependicular to the plane of the wall). Secure the box to the wall with mounting screws.

Stage 5

To adjust the door height, use a hex key. Before adjusting the door to the side, loosen the anti-burglary pins and mounting screws. Adjust to the side using the adjusting screw provided for this purpose. After adjustment, tighten the anti-burglary pins and mounting screws as far as possible.

Adjusting the hinges of the Jeld-Wen entrance door

Blade position outer door can be adjusted in height and horizontally using the hinge adjustment.

This is especially true, for example, when shrinking a house.

Height adjustment

Tools required: 5 mm hex wrench.

Door adjustment up

1. Loosen the upper adjusting screw (1) on all hinges by turning it with a hexagon 2-3 turns.
2. By turning the adjusting screws (2) on the bottom of the hinges, set the door to the desired height position.
3. Be sure to tighten all hinge screws an equal number of turns to evenly distribute the weight of the door on the hinges.
4. Tighten the retaining screws on top of all hinges (1).

Door adjustment down

• Loosen the lower adjusting screw (2) on all hinges except one by 2-3 turns.
• By turning the screw (2) of the remaining hinge counterclockwise, lower the door to the desired height.
• Tighten the adjustment screws (2) of the remaining hinges to the same position to evenly distribute the weight of the door across all hinges.
• Finally, tighten the upper adjustment screws (1) without excessive force.

Horizontal door adjustment

Tools required: 5 mm hexagon, Phillips screwdriver.

Increasing the distance between the door and the door frame on the hinge side

1. Tighten the adjusting screws (4) on one of the hinges so that the door leaf is in in the right position. .
2. Tighten the adjustment screws (4) on the second hinge (on the remaining hinges) to level the door leaf and distribute the weight of the door evenly.

Reducing the distance between the door and the door frame on the hinge side

1. Loosen the mounting screws (3) and the anti-removal pin (5) on all hinges by 2-3 turns.
2. Loosen the adjusting screws (4) on one of the hinges so that the door leaf is in the desired position. .
3. Loosen the adjustment screws (4) on the second hinge (on the remaining hinges) to level the door leaf and distribute the weight of the door evenly.
4. Carefully tighten the screws (3) and anti-removal pins (5).

Stage 6

Does the door close tightly?

The closing tightness can be adjusted using adjustments in the strike plate.

Stage 7

Carefully seal the gap between the wall and the frame, filling it mineral wool. Then coat the gap with a sealing elastic mass to vapor-waterproof the seam. Do not use polyurethane foam, because when it expands, it can deform the door frame and complicate possible subsequent door adjustments.

Instructions for servicing external doors

Painted products

The products are painted with moisture-resistant paints that meet the requirements for resistance to scratches, wear resistance and appearance surfaces that can withstand exposure to many household chemicals, grease and solvents.

Cleaning

Use regular ones detergents(non-alkaline), such as dishwashing liquid. To clean mold, use special means to remove mold. Do not use detergents that may scratch or dissolve the painted surface. Avoid, for example, the use of solvents, abrasive powders, metal fiber sponges, etc. Wet the surface from bottom to top, but wash it from top to bottom. Otherwise, streaks from drips may appear on the door. Wipe dry.

Service

Normal cleaning is usually sufficient unless the door is damaged or abnormally worn. To maintain shine, however, it is recommended, after washing, to rub the door surfaces, for example, with car wax.

Touch up

It is best to touch up minor damage with a brush and alkyd or acrylate enamel of a suitable color and gloss level, intended for outdoor use. First check the compatibility of the paint with the original painting material on a small surface, e.g. small area on the edge of the door on the hinge side.

Product quality and warranty conditions for Jed-Wen doors

Jeld-Wen manufactures its products in accordance with the requirements of the unified European standard CE.

What is CE?

The CE mark is a guarantee to the consumer that a given product complies with the essential requirements of a European harmonized standard and can therefore be legally placed on the market.

CE marking has long been mandatory on products such as toys and electronics, but lately, this unified standard is established for certain building materials.

What does this mean for the consumer?

All CE marked products carry product data in the Declaration of Performance (DoP) format, allowing clear and easy comparisons between similar products and providing the consumer with the information they need to make an informed decision.

The DoP provides key information on the performance characteristics of construction products that have been independently tested and certified by an EU body.

All products subject to these Directives are required to be marked with the CE mark, either on the product itself or on its packaging - the CE logo and a number which indicates the relevant DoP.

Failure of the product to comply with the CE standard in terms of bending of the blade or frame is considered a warranty defect.

We apologize if you encountered a defect in JELD-WEN products! If you find a defect, please contact us and provide your order number. Please note that a defective product cannot be installed or used!

How to measure whether a door leaf is curved?

Place the door leaf on a flat horizontal surface

Measure the distance between the center part door leaf and the surface on which it is located (mm)

Allowed curvature of up to 5 mm per door leaf

How to measure if a door frame is warped?

Curvature towards the wall

Place the box (flat) on a horizontal, flat surface so that the ends of the box touch the ground.

The allowed curvature of the box in the direction of the wall is 3 mm / per 1 meter (i.e. for a box with a height of 20M and 21M 6 mm per vertical of the box.

Curvature towards the edge of the box

Place the box on its side on a flat, horizontal surface with the ends of the box touching the surface.

Measure the gap between the center of the box and the surface (mm).

The allowed curvature of the box in the direction of the edge is 1.5 mm / per 1 meter (i.e. for a box with a height of 20M and 21M up to 3 mm per one of its verticals)

We are not responsible for product defects resulting from normal wear and tear, improper storage, installation and operation.

At the end of the 20th century, imported goods began to arrive in Russia in large numbers, including interior doors Finnish. They had noticeable differences from similar door designs that were previously manufactured in the country. Further, all doors with a similar design began to be called “Finnish doors”.

Such doors have three features that distinguish them from others:

1. There is a porch. The rebate is the part of the quarter (or rebate) edge that forms a projection above the end of the door. The edge creates another additional angle when abutting, which provides

• increased sound protection of doors,
• reduces drafts.

2. The door is equipped with embedded fittings. The universal latch lock and hinges are cut into place at the factory during manufacture. Any lever handle can fit the lock. If desired, a hole is made under the handle and a screw is placed to close the door from the inside. Due to the presence of a quarter on the canvas, only screw-in hinges are cut into.

3. Door frame This type of door is sawn at the factory at an angle of 45 degrees and manufactured to the required size. The box also contains a lock strike plate and hinges. These operations, performed at the factory, facilitate and speed up the installation of doors; you need to assemble the frame and then mount it into the existing opening.