How to glue rubber boots. How to glue rubber boots: well-known methods and little tricks. Preparing the product and applying glue

A small shard of glass, a nail or an ordinary push pin lying under the table is enough to render rubber boots completely unusable. The unpleasant surprise is aggravated by the fact that shoe repair shops Rubber boots are not accepted. Don't buy new boots. Let's try to figure out how to seal rubber boots with our own hands.

It is worth noting that rubber boots, like EVA boots, are not so easy to seal. Regular shoe glue won't take them, but superglue will ruin them.. You need special glue.

Angler's method

You can look for special rubber glue in hunting and fishing stores. The number of unsuccessful attempts will be reduced to a minimum if you know what your rubber boots are made of. To repair products made from PVC, polyurethane or EVA, completely different adhesives are required. Ask the seller for the glue you need and follow the instructions on the package. As a rule, the technology is the same: sand, degrease, glue a patch.

How to seal boots made of EVA, because they are porous? If you purchased special glue for EVA, then you won’t even need a patch. Carefully turn out the edges of the hole and apply glue to the porous structure until it is absorbed. Then line up the edges and press. After repair, even the boot will look quite aesthetically pleasing.

Cyclist's way

A proven way to reliably seal rubber boots is a bicycle repair kit. As a rule, it contains several patches per protective films, special glue and sandpaper. Rub the place where the patch is glued sandpaper, with an area slightly larger than the size of the patch. Then degrease it with acetone.

Remove the film from the patch and apply glue to the exposed surface; also cover the glued area on the boot with glue. After 5-10 minutes, when the glue has dried, press the patch firmly.

You can use repaired boots almost immediately, they will be completely sealed. One problem is that bicycle patches do not look very aesthetically pleasing, so they are only suitable for rubber country boots.

Motorist method

What to do if smart women's rubber boots need repair? Like EVA boots, they are best sealed without a patch. You can fill the hole in colored and transparent rubber boots with elastic adhesive sealant.

The “Crazy Hands” adhesive-sealant from the “Done Deal” brand has proven itself well. You can buy one in stores for car enthusiasts. For everything to work out as it should, do not neglect preparatory stages. After washing, dry the shoes thoroughly and degrease the hole with acetone. The quality of gluing depends on this.

Again, you also need rubber boots different glue- keep in mind that all of the listed materials are not suitable for leather.

IN lately Rubber boots are used not only in the country, on hikes or in the forest. Today these are fashionable and stylish shoes that save during heavy rains and floods. The shops are full of bright and colorful boots. However, even such strong and stable shoes can suffer and deteriorate.

The most common problem is a punctured sole. When stepping on a fragment, broken glass or even an ordinary pushpin, a hole forms in the rubber. It is very easy to puncture the rubber material, causing them to leak and become unusable.

But don’t rush to throw away your shoes; in some cases, the shoes can still be repaired. Let's find out how to seal rubber boots at home, how to fix a hole in the sole and in the boot.

How to prepare boots for repair

First, the boots must be thoroughly cleaned, washed and dried. You can seal your shoes with rubber or a patch made from old rubber. new shoes or tires. To do this, cut out the required piece of rubber and process it on each side with a file or sandpaper. The resulting rough surface will adhere to the glue more firmly and reliably.

Choose a special glue marked “rubber” or “shoe.” By the way, you can find a product for gluing rubber boots in a car store or stores for fishermen and hunters.

Take a glue-sealant that works great. When choosing a product, take into account the material the shoes are made of, since EVA and polyurethane require different means. Under no circumstances use classic PVA or “Moment”!

Dried boots need to be sanded and degreased using acetone or solvent. Before using glue, be sure to read the instructions and follow the recommendations.

If the sole, and not the boot, is torn, you must first make the surface smooth and even using sharpening machine. And only then you can glue the patch. Next, we’ll take a closer look at how to seal the sole and boot quickly and effectively.

Five ways to seal your boots

“Hot” gluing method using a vulcanizer. Rubber is used as a patch, which is pre-soaked in gasoline. The resulting patch is placed on the hole, clamped with a vulcanizer and left for half an hour. Then the device is turned off and cooled. Only after this can the press be removed;
A standard bicycle shoe will help you repair rubber shoes. repair kit, which includes special patches based on protective films, glue and sandpaper. Sand the desired area on the boots with sandpaper and degrease. Then remove the film from the bookmark, apply glue and glue it to the desired location. It is advisable to wait 6-12 hours and only then use the shoes. However, the appearance of a glued patch is not very aesthetic, so this method is suitable for repairing soles or for using boots in places where appearance doesn't matter.
We repair boots using special means for gluing rubber shoes. This is the easiest and available method. First you need to prepare the patch and boots for gluing. Don't forget to degrease the shoe surface. Apply glue to the patch and the gluing area in several layers and apply each layer after the previous one has dried slightly. Press the surfaces to be glued tightly and firmly against each other. To be more effective, you can tap the gluing area with a hammer. To prevent the patch from being noticeable, sand the surface of the sealed area with sandpaper;
If your boots have a porous surface, you can seal the holes without a patch. In this case, the edges at the cut site are turned out and generously lubricated with glue, and then pressed firmly against each other;
If you use glue-sealant, which is sold in car dealerships, you can also repair shoes without patching. First, degrease the bonding areas, and then lubricate the torn edges and press them tightly together.

How to properly care for rubber boots

If you choose the right glue and carry out the procedure carefully, you will be satisfied with the repair. And for boots to last longer, you need to organize proper care for rubber shoes and repaired products. After use, thoroughly clean and wash your boots in running water.

We offer several simple rules on the care and use of rubber shoes:

Wipe the outside of the rubber surface with a clean cloth. For very dirty shoes, first rinse in water and then wipe dry;
Colored boots are cleaned with Vaseline. It will retain color and shine, and the boots will not burst or become cracked;
Be sure to use shoe insoles, preferably warm ones. Wash insoles every two to three months;
Do not wear rubber boots in hot sunny weather, as the rubber deteriorates and fades;
Periodically lubricate the surface of the products with oil varnish with rubber glue or glycerin. This will keep the boots shiny;
Before long-term storage Be sure to lubricate your shoes with glycerin. Then wrap the items in newspaper or paper and place them in a cool, dry place;
Put away dark spots and stripes from rubber can be done using a regular school eraser. It should be soft and clean;
If your foot does not fit into the narrow top of the boot, lower the elastic stocking inside and put on the shoes. Then the leg will fit in without any problems, and the stocking can then be easily pulled out.

To keep your shoes shiny and attractive in appearance longer, lubricate the surface with oil varnish and rubber glue or wipe with a damp cloth containing glycerin. By the way, glycerin is an excellent product for caring for leather items. It will help smooth out the jacket from genuine leather and will give the product a presentable appearance. Read more about how to care for a leather jacket.

The most practical shoes that are specifically designed to protect your feet in rainy weather are rubber boots. But they may also need repairs, just like any other shoe. Usually the rubber diverges at the junction of the main part with the sole, grinds off, punctures, or bursts. To avoid spending money on a new pair and save on the services of a shoemaker, you can try sealing your rubber boots yourself. Thanks to this, they will serve you for many more seasons.

To repair your rubber boots at home, you will still need to spend a little money on consumables, some of which you probably already have at home and will come in handy in the future. But in any case, the costs will not be as significant as if you had to turn to a shoe repair specialist for help. So, you will need to have on hand:

rubber patch;
rubber glue;
a block and a regular hammer (may not be required);
a little solvent;
a piece of rags or ordinary cotton wool;
file;
sandpaper.

Instructions for repairing rubber boots at home

First of all, you need to prepare your rubber boots for the sizing process. Therefore, first wash them outside and inside with soap and a brush to remove dirt, then dry. Prepare a rubber patch. If you can’t find an original one cut from an old boot, you can use a bicycle inner tube.
Use a file along the back of your patch, as well as the seam around the puncture, to roughen the surface for better adhesion. Sand these areas similarly with coarse sandpaper.
Soak a rag or cotton wool in solvent and treat the patch and the area with the tear on the rubber boot. If there are particles of rags or cotton wool left on the surface, they should be removed.
Trim the edges of the patch so that it does not completely cover the treated rough surface. Now you can begin the main stage of repairing your rubber boots.
For gluing the patch, a special glue is suitable that can reliably fasten rubber surfaces (for example, “Rubber” or “ Super Moment"for rubber). You can contact a shoe repair specialist and ask him to pour special glue into your container for a small fee.
If you are using store-bought glue, read the instructions and follow all directions for use to get maximum results. Spread a thin layer of glue on the patch and the treated area of the boot, leave for 10-20 minutes (see instructions for time).
Place the patch coated with glue on the area of the boot and press firmly. For greater reliability, the boots are put on a last and tapped with a hammer. At the same time, you need to make sure that she does not move. The time for gluing the patch is at least 24 hours.

By following these simple instructions, you can always repair your rubber boots.

Almost every person has a pair of rubber boots in their wardrobe. Like any thing, rubber shoes crack over time. In order not to throw away your favorite pair, you can try to repair it. How to seal rubber boots is described in the article.

Preparing boots for repair

All it takes to damage rubber shoes is a nail, a small piece of glass, or even a sharp-angled stone. One wrong step, and the boot may get cracked.

Repair shops do not accept rubber shoes. This means that damaged boots can either be thrown away or repaired yourself.

How to seal rubber boots is a common question, the answer to which lies in knowledge of some of the features of such repairs.

First you need to determine the location of the puncture or crack. To do this, you can take a container of water and a damaged boot. Roll up the freebie, starting from the top edge, like a tube of toothpaste. You should get a tight bundle. Next, lower the sole into the water. Air will escape from the punctured area, forming bubbles.

The next stage of preparation is the mandatory cleaning of boots from dirt and dust, degreasing and drying. It is recommended to dry shoes away from heat sources. Drying rubber boots on batteries can lead to deformation, which will ruin their appearance and complicate the restoration process. All manipulations should be carried out carefully so as not to increase the size of the damage.

Then you should accurately determine the material from which the boots are made. Modern rubber shoes for women are made not only from rubber, but also from polyurethane and ethylene vinyl acetate (EVA). Each of these materials requires a different glue.

If it is difficult to determine the material of the boots on your own, you can take them with you to the store, where a specialist can quickly determine what the shoes are made of.

How can you seal rubber boots?

Many people immediately buy a universal strong adhesive known as “Moment” to glue cracks in rubber boots. In fact, the composition of this product not only does not glue rubber, but can also ruin it. Achieve good result You won't be able to do it with regular glue either.

Repair of rubber boots must be carried out with special adhesives. High quality products can be found in automotive and fishing stores. In this case, it is possible to purchase adhesives with a hermetic effect. They allow you to reliably glue cracks of any size and at the same time protect your shoes from leaking.

The choice of suitable glue depends on the technology of work. Today, there are several methods for restoring rubber shoes.

Anglers method

Fishing and hunting stores sell special ones. They contain instructions that describe in detail the technology for using the product. For rubber boots, it is generally recommended to sand the damaged surface and glue a patch.

How to seal rubber boots if they are made of EVA? This material has a porous structure into which glue is absorbed. To repair such boots, patches are not needed. It is enough to apply cracks on the lines required quantity glue and press tightly. The hardening time of the product is indicated by the manufacturer on the packaging. After gluing, the boots will look like new, and the defective area will remain invisible.

Cyclists method

This method has been tested by many cycling enthusiasts who often encounter the problem of a broken tube. To repair wheels, a bicycle repair kit is mainly used, consisting of patches on protective films, special glue for rubber and sandpaper.

According to this technology, it is necessary to rub the area where the patch will be placed with sandpaper, degrease with acetone and apply glue evenly. After a few minutes, apply the patch and press firmly.

The bicycle repair method is reliable and guarantees high tightness. You can use sealed boots almost immediately.

The disadvantage of this method is the unaesthetic appearance of the repaired product. A bicycle patch remains at the place where it was glued, which is impossible not to notice. Therefore, it is better to glue boots for the garden or fishing in this way.

Automotive method

Many women ask how to tape rubber boots on the fold so that it is not noticeable. Boots made of rubber or EVA most often crack along the fold lines. A patch in such places is not always suitable and can ruin the appearance. Rubber shoes for women require more careful repair, which can be provided by an elastic adhesive-sealant. It has a colorless viscous structure and is ideal for repairing colored and clear rubber boots.

Today there are automotive adhesives on sale different manufacturers. One of the best is the Crazy Hands sealant from Done Deal. You can purchase glue of this brand at any car enthusiast store.

Before applying the elastic bonding agent, it is necessary to treat the puncture or crack with acetone. After drying, apply glue.

Features of gluing soles

Rubber shoes can be damaged in the sole area. How to seal a cut on a rubber boot? In this case, you can use any of the methods described above. Only the preparation for gluing should be a little different. First of all, it is necessary to process the cut area on a sharpening machine. The surface to be treated should become perfectly smooth. If this step is missed, the repair will not give a good result. Next, you should adhere to the technology of the chosen method.

To repair soles, it is better to use adhesive sealants. Applying a patch in this area will not provide lasting results. When walking, the patch will quickly wear out, and soon there will be a need to replace it.

In order for repaired shoes to last as long as possible, it is important to know not only how to seal rubber boots, but also how to care for them.

Periodically wipe your shoes with a cloth made from soft fabric, soaked in a water-glycerin solution.
Dry rubber boots when room temperature away from batteries. Hot air may cause the glued parts to become porous. As a result, the shoes may leak again.
Clean your boots with a damp cloth every time after a walk. Dirt and dust can eat into the rubber, leaving stains. They are especially noticeable on light-colored shoes.
It is better to store rubber boots in cardboard box. For this purpose, it is recommended to keep the packaging in which they were sold.

Rubber boots are footwear necessary not only for the country house, but also for the city. They protect from bad weather and dirt. But it has one drawback - any nail or piece of glass is enough to render the shoes unusable. It’s impossible to give such boots to a workshop, but it’s a shame to throw them away. Therefore, many people prefer to repair their favorite shoes themselves.

How to care for boots

Rubber shoes must be properly cared for. And then you won’t have to resort to frequent repairs. After all, even the high quality guaranteed by the manufacturer does not always mean the safety of the shoes.

Rubber boots need to be cleaned properly. They are best washed with a solution of glycerin and water. In this case, boots should be wiped with a soft cloth and dried often to prevent fungus from appearing. Wet rubber boots cannot be dried with a hair dryer or radiator. It is necessary that the shoes dry naturally.

In order for the repair of boots to be successful, and for the shoes to last for a very long time, you need to know the following:

Before repairing, rubber shoes must be very thoroughly cleaned, washed and dried.
The patch can be cut from a tire or old rubber boots.
It is better to carefully process the patch on the reverse side with sandpaper or a file to make the surface rough for better setting glue.
It is best to degrease the surface of shoes with acetone and solvent.
You need to choose a special glue, which must indicate, for example, “shoe” or “rubber.”
Before repairing rubber boots, be sure to read the instructions from the glue manufacturer in order to do everything correctly.
It is best to smear the patch and the gluing area special glue several times, after waiting until the first layer dries a little.
When gluing the surfaces, you need to press them very hard against each other or tap the gluing area with a hammer.
A patch on a boot can be easily masked using sandpaper.

Method 1. You can seal your boots with special glue. It can be purchased in stores for hunters and fishermen. But in order to acquire the right glue, you need to know what exactly the shoes are made of. The fact is that shoes made of EVA or polyurethane require different adhesive compounds.

The seller can help you purchase the necessary glue by giving advice. Then everything is simple - you need to sand and degrease part of the boot and stick on a patch. If the shoes are made from porous material, then you can glue it without using a patch. The edges at the cut site just need to be turned out, generously coated with glue and pressed together.

Method 2. For this method you will need a regular bicycle repair kit. It contains patches on special protective films, sandpaper and, of course, glue. Clean the desired area on the shoe with sandpaper and thoroughly degrease. Next, after first removing the film from the patch, you need to apply glue to it and press the patch to the hole. You can use the shoes almost immediately, but it is better to wait at least 12 hours. The only drawback of this method is the unaesthetic appearance of the shoes after repair.

If the hole appears not on the boot, but on the sole, the gluing technology does not change. You just need to make the surface smooth and even, because usually the sole on such shoes is quite textured. This is possible using a sharpening machine. And only then glue the patch to this place.

But it is important to know that such a patch will not last long, especially if the sole of the boots comes into contact with a rough and hard surface very often. Therefore, it is better to wear such boots, for example, when fishing. Well, if the sole breaks again, the gluing procedure will need to be repeated.

Method 3. In order to seal women's boots without using patches, etc., you need to purchase an adhesive sealant. This can be done at any car enthusiast store. First you need to degrease the gluing area, and then lubricate the torn edges with glue and press them together. If you do everything carefully, the boots will look like new.

Method 4. This method of repairing rubber shoes is also called the “hot” method. It is not complicated, but it requires certain skills and, most importantly, a vulcanizer. Rubber pre-soaked in gasoline is used as a patch. It is placed on the hole in the boot and clamped with a vulcanizer. The device needs to be turned on for 20–30 minutes, then turned off and cooled. Only after it has cooled can you remove the press.

Don't despair if your favorite rubber boots suddenly break. It is enough to put in a little effort and the repaired boots will be no different from new shoes. You can use taped boots a day after the patch was applied. But if you don’t have time to wait, then you can wear them in an hour.