How to seal boots at home. The story of an EVA boot repair with a happy ending
Almost every person has a pair of rubber boots in their wardrobe. Like any thing, rubber shoes crack over time. In order not to throw away your favorite pair, you can try to repair it. How to seal rubber boots, described in the article.
Preparing boots for repair
All it takes to damage rubber shoes is a nail, a small piece of glass, or even a sharp-angled stone. One wrong step, and the boot may get cracked.
Repair shops do not accept rubber shoes. This means that damaged boots can either be thrown away or repaired yourself.
How to seal rubber boots is a common question, the answer to which lies in knowledge of some of the features of such repairs.
First you need to determine the location of the puncture or crack. To do this, you can take a container of water and a damaged boot. Roll up the freebie, starting from the top edge, like a tube of toothpaste. You should get a tight bundle. Next, lower the sole into the water. Air will escape from the punctured area, forming bubbles.
The next stage of preparation is the mandatory cleaning of boots from dirt and dust, degreasing and drying. It is recommended to dry shoes away from heat sources. Drying rubber boots on batteries can cause deformation, which will ruin them. appearance and will complicate the restoration process. All manipulations should be carried out carefully so as not to increase the size of the damage.
Then you should accurately determine the material from which the boots are made. Modern rubber shoes for women are made not only from rubber, but also from polyurethane and ethylene vinyl acetate (EVA). Each of these materials requires a different glue.
If it is difficult to determine the material of the boots on your own, you can take them with you to the store, where a specialist can quickly determine what the shoes are made of.
How can you seal rubber boots?
Many people immediately buy a universal strong adhesive known as “Moment” to glue cracks in rubber boots. In fact, the composition of this product not only does not glue rubber, but can also ruin it. Achieve good result You won't be able to do it with regular glue either.
Repair of rubber boots must be carried out with special adhesives. High quality products can be found in automotive and fishing stores. In this case, it is possible to purchase adhesives with a hermetic effect. They allow you to reliably glue cracks of any size and at the same time protect your shoes from leaking.
The choice of suitable glue depends on the technology of work. Today, there are several methods for restoring rubber shoes.
Anglers method
Fishing and hunting stores sell special ones. They contain instructions that describe in detail the technology for using the product. For rubber boots, it is generally recommended to sand the damaged surface and glue a patch.
How to seal rubber boots if they are made of EVA? This material has a porous structure into which glue is absorbed. To repair such boots, patches are not needed. It is enough to apply cracks on the lines required quantity glue and press firmly. The hardening time of the product is indicated by the manufacturer on the packaging. After gluing, the boots will look like new, and the defective area will remain invisible.
Cyclists method
This method has been tested by many cycling enthusiasts who often encounter the problem of a broken tube. Bicycle wheels are mainly used to repair wheels. repair kit, consisting of patches on protective films, special glue for rubber and sandpaper.
According to this technology, it is necessary to rub the area where the patch will be placed with sandpaper, degrease with acetone and apply glue evenly. After a few minutes, apply the patch and press firmly.
The bicycle repair method is reliable and guarantees high tightness. You can use sealed boots almost immediately.
The disadvantage of this method is the unaesthetic appearance of the repaired product. A bicycle patch remains at the place where it was glued, which is impossible not to notice. Therefore, it is better to glue boots for the garden or fishing in this way.
Automotive method
Many women ask how to tape rubber boots on the fold so that it is not noticeable. Boots made of rubber or EVA most often crack along the fold lines. A patch in such places is not always suitable and can ruin the appearance. Rubber shoes for women require more careful repair, which can be provided by an elastic adhesive-sealant. It has a colorless viscous structure and is ideal for repairing colored and clear rubber boots.
Today there are automotive adhesives on sale different manufacturers. One of the best is the Crazy Hands sealant from Done Deal. You can purchase glue of this brand at any car enthusiast store.
Before applying the elastic bonding agent, it is necessary to treat the puncture or crack with acetone. After drying, apply glue.
Features of gluing soles
Rubber shoes can be damaged in the sole area. How to seal a cut on a rubber boot? In this case, you can use any of the methods described above. Only the preparation for gluing should be a little different. First of all, you need to treat the cut area sharpening machine. The surface to be treated should become perfectly smooth. If this step is missed, the repair will not give a good result. Next, you should adhere to the technology of the chosen method.
To repair soles, it is better to use adhesive sealants. Applying a patch in this area will not provide lasting results. When walking, the patch will quickly wear out, and soon there will be a need to replace it.
In order for repaired shoes to last as long as possible, it is important to know not only how to seal rubber boots, but also how to care for them.
- Periodically wipe your shoes with a cloth made from soft fabric, soaked in a water-glycerin solution.
- Dry rubber boots when room temperature away from batteries. Hot air may cause the glued parts to become porous. As a result, the shoes may leak again.
- Clean your boots with a damp cloth every time after a walk. Dirt and dust can eat into the rubber, leaving stains. They are especially noticeable on light-colored shoes.
- It is better to store rubber boots in cardboard box. For this purpose, it is recommended to keep the packaging in which they were sold.
When the snow melts and the ground turns to mud, the dull autumn rains come and there are puddles everywhere, there are no better shoes than rubber boots. There are only times when you step on a piece of glass or get caught on a wire, and that’s all - a puncture or cut. They seem to be good boots, but they let water through. But we are not in a hurry to throw the thing away, we will try to repair it.
To repair rubber boots you will need: rubber glue(preferably Red sun or Moment), a grater or abrasive paper, scissors, raw rubber, a little gasoline. First you need to find the puncture or cut site. If the damage is not visible, then you should tighten the boot top so that the air in it is compressed under pressure. Place the boot in a basin of water, and where the bubbles are, there will be a cut or puncture site. You can insert a pointed match into the puncture so that the place is not lost.
A small shard of glass, a nail or an ordinary push pin lying under the table is enough to render rubber boots completely unusable. The unpleasant surprise is aggravated by the fact that shoe repair shops Rubber boots are not accepted. Don't buy new boots. Let's try to figure out how to seal rubber boots with our own hands.
It is worth noting that rubber boots, like EVA boots, are not so easy to seal. Regular shoe glue won't take them, but superglue will ruin them.. You need special glue.
Angler's method
You can look for special rubber glue in hunting and fishing stores. The number of unsuccessful attempts will be reduced to a minimum if you know what your rubber boots are made of. To repair products made from PVC, polyurethane or EVA, completely different adhesives are required. Ask the seller for the glue you need and follow the instructions on the package. As a rule, the technology is the same: sand, degrease, glue a patch.
How to seal boots made of EVA, because they are porous? If you purchased special glue for EVA, then you won’t even need a patch. Carefully turn out the edges of the hole and apply glue to the porous structure until it is absorbed. Then line up the edges and press. After repair, even the boot will look quite aesthetically pleasing.
Cyclist's way
A proven way to reliably seal rubber boots is a bicycle repair kit. It usually contains several patches on protective films, special glue and sandpaper. Rub the area where the patch is glued with sandpaper, an area slightly larger than the size of the patch. Then degrease it with acetone.
Remove the film from the patch and apply glue to the exposed surface; also cover the glued area on the boot with glue. After 5-10 minutes, when the glue has dried, press the patch firmly.
You can use repaired boots almost immediately, they will be completely sealed. One problem is that bicycle patches do not look very aesthetically pleasing, so they are only suitable for rubber country boots.
Motorist method
What to do if smart women's rubber boots need repair? Like EVA boots, they are best sealed without a patch. You can fill the hole in colored and transparent rubber boots with elastic adhesive sealant.
The “Crazy Hands” adhesive-sealant from the “Done Deal” brand has proven itself well. You can buy one in stores for car enthusiasts. For everything to work out as it should, do not neglect preparatory stages. After washing, dry the shoes thoroughly and degrease the hole with acetone. The quality of gluing depends on this.
Again, you also need rubber boots different glue- keep in mind that all of the listed materials are not suitable for leather.
Instructions
Cut out an outsole from thin microporous rubber.
Take rubber glue, glue “88” and mix both compositions in a 4:1 ratio. Apply the resulting mixture in a thin layer with an old toothbrush. sole boot and outsole. Try not to let the glue clump. The applied glue should dry for 5 minutes.
Now again spread the prepared mixture onto the leather sole. Dry the glue again for a few minutes and firmly connect the surfaces to be glued. Leave the item being repaired under the load for one day. Now trim the protruding edges of the outsole with a sharp knife. Your updated one is ready to serve you further.
Video on the topic
Sources:
- How to repair shoes
It often happens that the shoes still look quite decent, but the soles have peeled off a little. What to do - run to the master shoemakers or try to eliminate the trouble on our own? Fortunately, there are a lot on sale today quality adhesives. So if the sole has peeled off just a little, try fixing the boot yourself.
You will need
- - special glue 88;
- - ordinary rubber glue;
- - rasp or sandpaper;
- - a piece of cotton fabric;
- - iron;
- - rubber glue;
- - nylon;
- - soldering iron.
Instructions
Take special glue 88 and regular rubber glue. Mix one part of glue 88 and four parts of rubber and grind thoroughly so that there are no lumps left.
Next, take the boot and start cleaning sole. For this painstaking work, use a rasp or coarse sandpaper. Clean up sole you need to be very careful so that no dirt remains on it.
Spread both parts, that is sole and the boot with a mixture of glue, fold it well and then press the boot down with pressure, first making sure that the glue and the boot are as even and neat as possible. It is advisable to let the boot dry for about a day. After that it is already possible.
It happens that the sole falls off the shoe completely. Then it and the shoe need to be thoroughly cleaned in the same way, using a mixture of glue. Next, the glue is applied to sole. Leave it for about five minutes. After that, apply a second ball of glue, wait another minute and stick sole to the shoe, make sure it comes out neatly. After gluing, put it under pressure and wait about a day.
Another method of gluing soles can be used to glue a new sole to an old sole as a “prevention”. To do this, take an improvised adapter - a piece of cotton fabric. It needs to be welded to the old sole using an iron. Stick a rubber band on this adapter sole. For gluing, use the most common rubber glue.
If the sole has come off at -, then it can also be successfully re-glued. For this you need to clean it very well. Next, place a strip of nylon along the perimeter of the sole and a new one on top of it sole, then use a heated soldering iron to melt the nylon. After this, press firmly sole.
Please note
Remember that such home renovation Suitable for boots and shoes if you are not afraid of the consequences of the experiment. If the shoes are too valuable for you, then you should contact a professional master.
Shoe repair is a responsible and serious matter. This is why many people prefer to have it done by a professional shoemaker. But there are also times when you have to repair shoes yourself. How can I fix it? sole?
Instructions
First of all, prepare the thread for stitching the sole. To do this, take a very ordinary thread and simply treat it with tar or wax. Thanks to this, the thread will become water-repellent and will not mechanical influences unwind into individual fibers. Then take the shoe. Now step back at least 5 mm from the edge of the grant and draw a stitching line in a circle with a pencil.
Take an awl that has a hook at the end. Pierce it along the intended line sole. Make small stitches with an interval of no more than 10 mm. Try to tighten each stitch as much as possible so that the thread in no case gives any slack and certainly does not form loops. The stitches must be made in such a way that the thread is not visible from the outside. In addition, it is recommended to make a small indentation along the seam line. But don’t spoil it by making such a channel. Better practice first.
There is another option for fixing the sole. However, it will require you to have skills in working with glue. Lightly strip sole coarse sandpaper or rasp. Take two types of glue: rubber and “88” glue. Now they need to be mixed with each other in a 4:1 ratio. Apply a thin layer of the mixture to the outsole and sole shoe with an old toothbrush. Try to carry out the entire procedure so that the glue does not form clots. Give the applied glue 5 minutes to dry.
Re-treat the leather with the prepared mixture. sole. Dry the glue again for a few minutes, and then firmly and forcefully connect the surfaces to be glued. Leave the shoes being repaired under a load for the whole day. Then trim the protruding edges of the outsole with a sharp knife. That's all the repairs. Your updated shoes will serve you for a long time.
If the soles of your favorite shoes or boots have become unglued, you can fix them yourself. Having at hand necessary materials, it’s not at all difficult to do. The main thing is to follow the instructions exactly. Then the shoes will serve you for another season.
You will need
- - pure gasoline;
- - glue 88N;
- - needle file;
- - soldering iron;
- - dratva;
- - awl;
- - shoe hook;
- - prevention.
Instructions
Before you begin repairs, determine what the sole is made of. Usually it is rubber or made of . If the sole is rubber, clean it of dirt and thoroughly degrease it using a clean one. After this, apply 88H glue on it and wait until it dries. This usually takes 10-15 minutes. Stuff your shoes with newspaper or any thick paper. Place it under the press for 8-10 hours.
If the sole is made of polyurethane, clean the bonding area from dirt and degrease with clean gasoline. Take a flat file and carefully file away the colored layer of leather. Degrease the surface to be repaired again. Using a heated soldering iron, spread small pieces of polyurethane (cut from the sole) over the skin in the area that needs. Squeeze sole And top part in the place of gluing and pass a soldering iron between them. Keep in mind that this type of sole requires some training. Accurately maintain the pressure between the sole and the upper of the shoe and monitor the temperature of the soldering iron. The device must be very hot.
If the peeled sole has an edge that extends onto the shoe, it can be repaired in another way. Clean the damaged area from contamination and degrease with clean gasoline. Apply to sole and apply 88N glue to the upper skin in place. After 10-15 minutes, press as hard as you can sole to the top. Take a thread (strong twisted linen thread) rubbed with shoe polish. Using an awl and a special shoe hook, sew sole to the top of the shoe. Remember that the seam should be at a distance of 4-5mm from the top edge of the sole.
If small cracks appear and it begins to peel off, you will need 88H glue and rolling (prevention). Clean the damaged area and degrease with clean gasoline. Apply glue to sole and for prevention. After 15 minutes, stick the roll on sole and place under a press for 8-10 hours.
Often, with active and constant use of shoes, they very quickly become unsightly: the seams begin to come apart, the sole becomes deformed or comes off. In this case, it will take a little time to get the boots in proper shape. With everything you need on hand, you can quickly seal your shoes yourself. Thanks to this, it will serve you for more than one season.
You will need
- - Sandpaper,
- - glue “Moment”,
- - acetone or gasoline,
- - a rag.
Instructions
Before we start repairs shoe, we need to prepare them properly for this. To do this, wash your shoes thoroughly with a brush and soap, rinse clean water and leave to dry naturally at room temperature for at least one day. If the shoes do not dry enough, then it will be very difficult to glue the materials to each other, since the moisture will continue to evaporate. In this case, there is a possibility that they will break the next day.
Take a small piece of material or a regular cotton pad and soak it in acetone. Treat both surfaces to be glued properly, this way you will not only remove any remaining dirt, but also degrease the surface of the shoe. If the gap in the boot is large enough, in this case it is recommended to clean the surface of the material using fine-grain sandpaper. Thanks to this, they will stick together much better and stronger. For degreasing, you can use regular gasoline.
Apply enough good layer Apply suitable shoe glue to the gluing area and leave to dry for 10 minutes. After this, carefully connect shoe s and press firmly, hold for a while so that the surfaces can fix and remove excess glue. After that it remains to put shoe under a press for a day, this could be a chair leg or another object. For gluing shoes, Moment glue is best suited, which is sold in large tubes and has yellow. You shouldn't use super glue, it won't work. desired result.
If shoe unstuck again, then there is a better way that will really help maintain the shape of the shoe - stitch it. In this case, it is advisable to contact a specialist - a shoemaker. If you decide to sew them up yourself, in this case you will need fairly strong threads and a thick shoe needle, as well as a lot of strength and patience.
Video on the topic
Before going outside, especially in wet and slushy weather, be sure to treat your shoes with special impregnations and wax, which can be bought at almost any shoe store or market. This will help keep your shoes in good condition and your feet dry.
Unfortunately, shoe soles sometimes crack. As a rule, patches installed on a crack do not give the desired result - the shoes continue to get wet, and the “patch” quickly falls off. How to repair a burst sole?
You will need
- - acetone or gasoline;
- - sandpaper
- - bicycle camera;
- - rubber glue;
- - shoe knife;
- - soldering iron;
- - nylon.
Instructions
Cut the edges of the sole around the crack to a width of 5-7 mm using a shoe knife. The cutting depth should be one millimeter.
Carefully measure the depth of the crack in millimeters. Add 15 mm to this value. Take an old bicycle inner tube and cut a strip out of it, the width of which will correspond to the result obtained.
Sand the strip using sandpaper. Degrease using acetone. Lubricate the strip rubber glue on both sides. In this case, on one side the glue must cover the entire surface completely, and on the other side it is necessary to leave dry edges. The width of these edges should be 5-7 mm.
And the question arises, ?
But after using the method of gluing with rubber glue, many people get upset because for some reason the patch falls off.
It’s strange that the glue is rubber, but it doesn’t stick to rubber?
Yes, it really doesn’t hold, and even if it does, it doesn’t last long.
Then we try another method, take it to a shoe repair shop. And there they say: “We don’t glue rubber shoes.”
It’s strange again, a shoe workshop, but they don’t take shoes for repairs.
And indeed, shoemakers rarely undertake the repair of rubber shoes. The only thing they can advise is to go to a car repair shop where car tires are vulcanized.
But, most likely, they will refuse you there, saying that this rubber cannot be vulcanized, or they will even say that they no longer have such a service, since now many drivers have switched to new types of tires where vulcanization is not used.
What to throw away? But I really need them.
Don't worry, there is a way out!
I offer you one of the most effective and proven methods, namely, how to glue a patch to rubber shoes.
Although it won’t add any beauty, the patch will stick.
IN at the moment you can quickly and reliably patch rubber boots with a miracle invention that lately used by cyclists.
It's called a camera repair kit.
It's not expensive but it sticks perfectly. Of course, I can’t guarantee 100% that it wakes you up exactly as you want, but I tried it, it works.
It includes ready-made patches, by the way different sizes, glue and even sandpaper (may not be available everywhere).
It is very easy to glue them. Instructions are always included with it.
I’ll add from myself:
- Mark the place where it is necessary to patch, applying a patch of the required size accordingly
- Sand well with sandpaper (some people advise degreasing with gasoline, but I would not recommend doing this at all if the shoes are clean and not greasy, and if degreasing, then only with acetone)
- Apply glue to the selected area on the boot
- Remove protective film from the patch and smear that side with glue (someone will have a question about which side to smear on the patch - I repeat the one under the film, but after gluing, a colored rim on the patch will be visible)
- Let the glue dry for about 10 minutes and press.
Of course, you shouldn’t wear it right away, wait a while, and it’s better to wear it the next day.
If a hole appears on the sole, then of course a different approach is needed.
First, this place must be processed on a sharpening machine so that the surface becomes perfectly smooth, otherwise everything will be useless. And then we glue it as usual.
But keep in mind that this patch will quickly wear out if you walk in it, say, on asphalt. That is, it is designed to go into the water, but not for long walks.
But in principle, if it wears out, you can do the previous procedure again.
So, it's possible quickly and reliably!
But as you noticed, we were talking about simple rubber shoes, which are intended for ordinary household chores.
