Christmas tree from plastic bottles. Christmas tree from plastic bottles. Master Class. We make a Christmas tree out of paper with our own hands - a master class

We consider green plastic bottles to be just trash. But on New Year's holidays and in skillful hands, they can turn into real forest beauties! The Christmas tree does not have to be live or bought for a lot of money. In this article, you will get acquainted with several options for creating a Christmas tree from plastic bottles with your own hands.

Tall artificial tree

From plastic bottles you can make not just a small craft, but a real tree that can be decorated. To do this, you need to prepare a steel rod. Its length is equal to the height of the finished tree, it is best to take a segment of 0.5 m. Do not forget about the thickness of the rod, the structure must be stable. The ideal diameter is at least 5 mm. Also prepare a solid aluminum wire, green plastic bottles (at least 30 pieces), scissors, hot glue and a craft stand.

To make spruce, you will only need the cylindrical part of the bottles, so immediately cut off the neck and bottom of all of them. Carefully cut the resulting cylinders in a spiral.

You should get stripes 2 cm wide. Now bend one edge about 5 mm, this will allow you to set the right direction for the needles. Cut the fringe, retreating 1 mm. You need a lot of fringes!

Christmas tree: large craft

When the blanks are made, proceed directly to the creation of the tree. Start at the top. Wind the strip about 8 cm around the rod and secure with a glue gun. Now twist a small piece of fringe with a roll and glue it inside the cylinder on the rod. Then we wind the fringe already on a strip of plastic and glue it. When a piece of fringe ends, just take the next one and continue gluing. The top of the Christmas tree made of plastic bottles is ready!

Let's start creating branches. The upper ones are the shortest (about 6 cm). Bend the frame from the wire (a ring and three beams extending to the sides). Put it on the rod. Wrap the frame with fringe.

Finishing work on a large spruce

When the first tier is done, wrap the space underneath with fringe and move on to the second tier. It will consist of four branches, each of which has two small branches. The length of the branches is about 9 cm. Wrap the frame and the second spacer with plastic needles.

The branches of the third tier should be about 10 cm long, the lowest - 15 cm. But the four tiers of the Christmas tree craft are not the limit. You can make the spruce much taller. The main thing is to make each tier wider and more branchy.

It remains to make a stand. You can make it yourself from two boards or buy it ready-made in the store. Well, do not forget to dress up the plastic beauty with beautiful New Year's toys. Such a craft requires perseverance and patience, but the result will please you very much!

High Christmas tree made of plastic bottles: instructions

If you are a fan of creative interior decorations or just want your child to take to school, kindergarten a wonderful craft for an exhibition dedicated to the New Year, make just such a PET Christmas tree. Prepare about 35 bottles, scissors, candles, a pot, and a plastic tube.

35 green bottles are enough for a craft about 1.2 meters high.

Cut off the bottom of all bottles and cut the plastic along almost to the neck into strips 1.5 cm wide.

Now it's the turn of not the most pleasant stage of creating a Christmas tree from plastic bottles with your own hands. Do it in a ventilated area. You need to run each strip on each bottle over the candle flame every 2 cm. This will take time. After each bottle, heat over a candle and straighten the segments like the rays of the sun.

On the base, strengthen the plastic tube and put your workpieces on it. Now trim the spruce with scissors so that it has a cone shape. This craft looks good in a summer cottage, especially powdered with snow. But if you dress it up with tinsel and toys, a fluffy plastic spruce will decorate the apartment.

Small PET Christmas tree

A small craft can decorate a table or shelf. It does not take as much time to make it as for previous Christmas trees. Yes, and you only need six bottles. Also take plasticine, green paint, a brush, scissors, a 50 cm long rod and a pot. Cut the PET roughly in half and discard the bottom part. Cut the parts with a neck into 8 teeth, cut each of which obliquely. Bend the strips upwards, like paws of fir trees. Color the resulting blanks green and dry.

Strengthen the rod in the pot and, using plasticine, strengthen the paws of your spruce one by one.

Cut off the top branches. Then decorate the tree. Now you know how to make a Christmas tree from a plastic bottle. Naturally, such a tree does not look like a real one, but how many joyful minutes you can bring to the kids by working on crafts!

Christmas tree from two bottles

Above are crafts from a fairly large number of plastic containers. And how to make a Christmas tree out of plastic bottles with your own hands, if there are not a lot of them? Take two bottles, a sheet of paper, scissors and tape.

Cut off the neck and bottom of the bottles. Roll a piece of paper into a tube and insert into the neck. Reinforce the upper end with tape, otherwise the tube will unwind. Be sure to trim the cut so that the craft stands firmly on the surface. Cut the remaining parts of the bottle into rings about 8 cm wide. Make a fringe out of them, without cutting 1 cm to the edge. The thinner the strips, the fluffier the spruce. Let all the strips be equal in width, it looks neat. Fasten the fringe to the paper barrel with tape, starting with the widest strip.

After finishing the formation of spruce, decorate its top. You can use leftover bottles or a red or gold star. Put mini balls on the branches, and the spruce is ready!

original christmas tree

Such an intricate craft will decorate the table on New Year's holidays, and in the rest of the year it can easily keep houseplants on the windowsill company. Take one plastic bottle, scissors, a candle, a cork stopper, a glass of baby yogurt or cottage cheese, glue and foam rubber (you can use a sponge for washing dishes). Cut the bottle into squares of different sizes, from which then make stars (preferably not five-pointed ones). Cut the ends of the stars thickly into a fringe with scissors.

Then bring the edges of the blanks to the candle flame for a couple of seconds, so they will bend up beautifully. Cut the foam into small pieces. Lubricate the largest workpiece with glue and attach a piece of sponge, put the next piece of plastic on top. Thus, collect the craft completely. Such a do-it-yourself Christmas tree made of plastic bottles resembles a children's pyramid according to the assembly technique.

Then cut a bucket out of the glass and place a cork inside - this is the trunk of our tree. Glue the tree to the cork and you're done.

This is how you can create a real miracle from ordinary plastic bottles!

Make a Christmas tree with your own hands, cheap, cheerful and, in addition, quickly? This is possible, especially if your house has accumulated some plastic containers - bottles or cups.

We present to your attention a double detailed master class: how to make an exclusive New Year's building from recycled materials with your own hands.

Master class 1: Christmas tree made of plastic bottles

We will need:

plastic bottles of different sizes, from 0.3 to 3 liters. Preferably green;
a wooden stick, the height of which is the same as our Christmas tree will be. The diameter of the stick should be slightly smaller than the diameter of the neck of the bottles;
bottle cap;
stationery knife;
scissors.

Stage one:

Carefully cut off the bottom of all plastic bottles. Carefully, with a clerical knife - first you need to make a puncture in the wall, and only then cut along the circumference. If sawing with a knife seems difficult, then you can cut with scissors. We leave one big bottom - it will serve us as a support on which the Christmas tree will hold. The rest of the bottoms can be thrown away.

Stage two:

Bottles with sawn-off bottoms are cut into strips, 2-2.5 cm wide, of course, without bringing the cut to the neck. As a result, we get a kind of plastic "flower".

Stage three:

We cut each strip along the edge, leaving a distance of 0.5 mm between the cuts. These are our "pins". Thus, we will be able to make the future Christmas tree “fluffy”. We bend each “needle” - the branches turn out to be “lush”.

Stage four:

We carefully string the branches on a stick with our own hands - this is how the Christmas tree is assembled. Wider blanks (from larger bottles) will naturally be at the base, and smaller ones (bottles of smaller capacity) at the top. We put the bottom of the bottle on a stick, this will be the base on which the tree rests. We wind the lid on top, you can hammer a nail for strength.

Christmas tree made of plastic bottles is ready! Decorate! On such a peculiar New Year's beauty, tinsel, rain and simple matte balls will look great. A garland on an ascetic plastic tree can also look very stylish. Experiment!

Master class 2: how to make a Christmas tree from cups

The most difficult thing in this procedure is, perhaps, to find green cups.

We will need:

plastic cups;
stapler;
glue;
toys, balls for decorations.

Stage one:

We lay out eight cups with our own hands in the first row, in a semicircle. We fasten them with a stapler. Then we lay out the second row on top - already seven cups. We also fasten them with a stapler. And so on, each row is one cup less. Rows between themselves can be slightly glued, for reliability, and also fixed with braces. The finished tree must be stable.

Stage two:

We put a toy or a ball in each cup. You can drop a little glue so that they are securely fixed inside. By the way, if you have a special glue gun - great, it will help you discreetly attach toys to plastic.

The original Christmas tree made of plastic cups is ready! But if it seems to you that this idea is not creative enough, then here are options for decorating or modifying such a structure with your own hands:

You can lay out the cups not in a semicircle, but in a circle. Only in this case it is better to “plant” them on a cardboard cone base. Such a tree will have an attractive "facade", that is, it can be placed in the center of the room, while a semicircular tree looks good when it stands against the wall.
If you make a small incision in the top of each cup, you can pass a ribbon through it, secure it with a knot and hang a decoration on it.
Pasta-bows painted with golden gouache will look great as decorations.
A garland can be placed inside a round Christmas tree made of cups. It will shine very nicely through the plastic, and its top bulb will perfectly replace the traditional star.

The largest bottles should be at the bottom (2 and 1.5 liter, in the middle - liter, and at the top 0.5 and 0.3 liter bottles. If you have bottles of the same volume, then adjust the length of the “branches” yourself by cutting strips to desired length.

In the left bottom, make a hole, which is fixed on the lower end of the stick with a plastic bottle cork (for strength, you can hammer in a nail).

Put the last, smallest part on the upper end of the stick with the neck up and screw the green cork onto the neck, also securing it with a nail for strength.

A little patience, perseverance, diligence and the forest beauty is ready!

Such Christmas trees can be used as a New Year's decoration for your homes!

Method 2. To make such a Christmas tree, you need a minimum of time and cost. A master class on making a Christmas tree from plastic bottles will tell you in detail how to make such an original New Year's craft

To make a decorative New Year's craft: a Christmas tree from plastic bottles, you will need the following:

Plastic bottles - 3 pcs;
Scotch;
A sheet of thick paper, ideally whatman paper (A4);
Scissors;

	So, cut the bottle as shown in the photo. That is, it is necessary to cut off the bottom and neck so that a straight pipe from the bottle remains.
	Next, you need to make blanks for the branches. In order for the Christmas tree to have a conical shape, the blanks must have different sizes. That is, you need to achieve the following:
	Cut each plastic bottle lengthwise into 3 equal parts and only then adjust their sizes so that each subsequent tier is slightly smaller than the previous one. Then each blank must be "dissolved into needles." The neck of one of the bottles will serve as a stand for our future New Year's crafts.
	The next step is to roll the paper into a tube. Insert into the bottleneck...
	... and secure with tape.
	Now it remains to fix each tier of the tree with tape in a circle and a small New Year's craft: the tree is ready with your own hands!
	You can decorate the top of our Christmas tree with a homemade Christmas tree toy, or you can complete the Christmas tree the way we did.
	If you want to make a Christmas tree from plastic bottles more fluffy, like in the photo, when making a Christmas tree, the needles need to be cut as thin as possible (more often).
	By the way, the Christmas tree looks quite creative with larger “branches” - a master class from the Country of Masters website. We cut the bottle in the same way as in the previous version into 3 parts. Only cuts are made in a circle to the center, straight.
	In the center, a puncture is made with an awl and the needles are bent up and down in order. In the lid of a cream or mineral water, a puncture is made into which a skewer of the desired length is inserted.
	The parts are strung in descending order, a large bead is placed on top of the glue. The Christmas tree can be decorated with foam, rain, etc.
	Glue the Christmas tree to the stand from the disk. Christmas tree is ready!
	Nearby you can put gifts or plant an animal. Such Christmas trees have been a success for many years.

Method 3. And, finally, the last option for today is a Christmas tree made of plastic milk bottles (what decorative Christmas Trees just don’t make from ...). The design is completely collapsible, has the maximum similarity to the original, does not require particularly complex technologies and specific work skills, there is no problem with bottles either, well, the holiday is on the nose ...

Materials and tools

The material for making a Christmas tree is a milk plastic bottle or part of it (Fig. 1). To make a homemade table Christmas tree, you need 5-20 milk / kefir plastic bottles with corrugation at the bottom. The number of bottles determines the number of branches and tiers. The more branches, the more fluffy the Christmas tree turns out, the more tiers, the higher it is.

In addition to bottles, you only need scissors and plastic rivet technology

plastic rivets

To implement the technology of plastic rivets, it is necessary to have a means for melting (installing) rivets and the rivet itself. You need to manage to melt the head of the rivet with a hot nail or a lighter. You can similarly do this with a well-heated soldering iron. In addition, you will need clamps and tweezers to install rivets in hard-to-reach places.

For plastic rivets, it is very important to choose the material. Fluttering for about a year, by trial and error, taking into account the requirements of strength and accessibility, I identified several sources for obtaining plastic rivets:

1. Empty refills from ballpoint pens. Fairly affordable material. They are good because they are colorless and the connection, with their help, turns out to be organically inscribed in a product made of plastic bottles. Such a rivet turns out to be neat, with a round head, however, it has a slightly reduced tensile strength. In addition, the rod from ballpoint pens is round in cross section and completely fills the drilled hole in the parts to be joined. By the way, the walls of the rods come in different thicknesses, for rivets it is better to use rods with thicker walls.

2. Sticks from Chupa Chups. Similar to option No. 1 only in color. The connection turns out to be more bulky, and the head of the rivet is melted with difficulty (either burns out, or becomes ugly, or unreliable).

3. The most ideal option, and very convenient (I give the world an offer) to use material from buckets with building mixtures of 3, 5, 10 liters. There are quite a lot of them left after repairs, and one lasts for a long time.

From the walls of such a bucket, you need to cut a ring, and cut the ring along the generatrix (necessarily only this way) into strips 2 ... 4 mm wide, 4 to 15 cm long. quantity.

Getting a connection with such rivets is unpretentious. It is more convenient for this to pre-prepare rivets of the desired length, on the one hand, melting the head of the plastic rod. To connect two parts with plastic rivets, we overlap the parts, melt them with the same burner, forming a hole of the desired profile and size, insert a rivet there and, by melting, form a head from the opposite end of the rivet rod. Having practiced several times in reflow, the head is neat and tear-resistant.

Let's get started...

To implement the idea, the source material is needed in the form of a part of a milk plastic bottle (Fig. 1a), which is cut along the circumference into two components (Fig. 2 and Fig. 3, respectively). A trunk will be formed from the part adjacent to the neck (Fig. 1b), and branches of the future Christmas tree are cut out of the ring with a central groove (Fig. 1c). From one whole plastic bottle, two or three rings are obtained. The more rings you prepare, the more fluffy and tall Christmas tree you can collect. I had 20 such rings, no less (10 full bottles).

Plastic rings with a groove in the middle must be cut into several equal parts (Fig. 2) along the generatrices of the bottle cylinder. As a result, we get convex rectangles. If cut into 2 parts, then long lower branches of the Christmas tree will be obtained from such long halves, if cut into 3 equal parts, then branches of medium tiers and medium length will be obtained, and cutting into 4-5 parts, we get small blanks for the upper tiers of the desktop Christmas tree . It is not at all necessary to observe the special uniformity of the dimensions of the rectangles for one type of tiers.

Next, the rather tedious work of forming a branch begins. From each plastic convex rectangle (Fig. 3a), a wedge-shaped blank should be cut with scissors (Fig. 3b). The axis of symmetry of the wedge-shaped part should be along the corrugation groove. Immediately after cutting the workpiece, “needles” should be formed on it, making cuts along the side edges at about 45 degrees to the groove and radially at the end of the “branch”. (Fig. 3c). The needles are alternately bred from the plane of the workpiece also at 45 degrees to each other. The wiring of needles up and down relative to the plane of the branch provides fluffiness to the Christmas tree.

As a result of such painstaking work, several sets (Fig. 4) of branches of different sizes for a desktop homemade Christmas tree are obtained. Cutting branches and then needles is a rather lengthy task, but you can entrust this to your relatives as part of the collective creativity to decorate life for the New Year. It should be noted that it is difficult to accurately determine the number of branches that form a particular tier by eye, so you should always have several rings in stock (Fig. 1c) for cutting branches during the installation of tiers

The place for fastening the branches is the trunk, which consists of several parts (logs). The upper parts of plastic bottles (Fig. 1b) were considered waste during the separation of the rings (Fig. 1c), but now they are also used in spruce construction to create a trunk. The base of the trunk and the lower log is the full neck part of a plastic bottle (Fig. 5a). The upper logs are assembled from blanks obtained by cutting off the threaded part of a milk bottle with a flange, as well as removing a plastic segment along the generatrices (Fig. 5b, 5c). The segments must be rolled up with a tube and fixed on both sides of the generatrix with plastic rivets. Similarly, it is necessary to create several logs for attaching tiers of branches. In my case, these are 3 logs, but there may be more or less of them. For a miniature Christmas tree, 3-4 tiers of branches on just one log are enough.

Naturally, the diameter of the trunk should taper towards the top of the table tree and the diameter of the top log should be smaller than the bottom one. The larger the cut of the segment, the more top log is obtained from the tapered top of the plastic bottle. For the top, you need a half segment, and for the middle part, about two-thirds of the whole neck (Fig. 5b). The diameter of the bottom hole of the top log should be approximately 1 mm larger than the top hole of the bottom log forming the trunk.

It's time to attach the branches to the "logs". On each log, you will need to place 2-3 tiers of branches. A small number of tiers does not allow you to effectively cover the rivet heads with branches, and a large number spoils the aesthetic appearance of the Christmas tree. In each tier of this design, you can install from 4 to 10 branches. Fastening is carried out with the help of plastic rivets, since quite a lot of plastic rivets will be required, it is better to prepare them for future use. The easiest way is to install branches in tiers on the lower logs (Fig. 6), since the neck in a plastic bottle is wide enough and it is convenient to hold the plastic rivet on the inside with your finger.

If you put the branches close to the circumference of the tier, then one rivet is enough to fasten the branch to the trunk (Fig. 6-8). For lovers of greater reliability, two rivets can be installed side by side. Tiers of branches must be formed like a flooring for the roof of a house - from the bottom up, then the branches of the upper tier will cover the rivets of the lower one and the heads of the rivets will be completely invisible.

In my case, in the lower (Fig. 6) and middle (Fig. 7) logs of the trunk, there are 2 tiers of branches, and in the upper - 3 (Fig. 8). In total - 5 tiers of branches. It is quite enough to acquire an amazing similarity with a real Christmas tree. The installation of plastic rivets on the upper tier, due to its small diameter, should be done using tweezers or a medical clip.

After fixing all the tiers on all the logs, you can proceed to the final assembly. But first it is desirable to decide on the top. In my case, without thinking for a long time, I built the top using the same technology as the barrel (Fig. 5), that is, turning the plastic into a cone. But you can do this in a different way, for example, in the form of an asterisk or a ball (I like the cone more). The top of the tree is attached to the upper element of the trunk also with the help of a rivet that is installed from the inside and melted from the outside. The upper part of the trunk, together with the top, already has a miniature table Christmas tree in itself (Fig. 9). It can be installed on the monitor and enhance the feeling of the holiday...

A live Christmas tree grows from the bottom up, in the same order we collect logs with tiers of branches by adding “logs” (Fig. 10) to an existing Christmas tree. Between themselves, it is better to connect the elements of the trunk in a place covered with a branch, at three points along the circumference of the trunk. In this case, the trunk acquires rigidity and will not break if the Christmas tree accidentally falls to the floor from the table, then the Christmas tree is desktop ...

And if you insert a light-dynamic part (for example, a garland) inside the Christmas tree, then on New Year's Eve it will amaze those around you with its charm:

Here is such a master class. Of course, a little complicated, but what a beauty it turns out!

In the left bottom, make a hole, which is fixed on the lower end of the stick with a plastic bottle cork (for strength, you can hammer in a nail).

Put the last, smallest part on the upper end of the stick with the neck up and screw the green cork onto the neck, also securing it with a nail for strength.

A little patience, perseverance, diligence and the forest beauty is ready!

Such Christmas trees can be used as a New Year's decoration for your homes!

To make a decorative New Year's craft: a Christmas tree from plastic bottles, you will need the following:

Plastic bottles - 3 pcs;
Scotch;
A sheet of thick paper, ideally whatman paper (A4);
Scissors;

	So, cut the bottle as shown in the photo. That is, it is necessary to cut off the bottom and neck so that a straight pipe from the bottle remains.
	Next, you need to make blanks for the branches. In order for the Christmas tree to have a conical shape, the blanks must have different sizes. That is, you need to achieve the following:
	Cut each plastic bottle lengthwise into 3 equal parts and only then adjust their sizes so that each subsequent tier is slightly smaller than the previous one. Then each blank must be "dissolved into needles." The neck of one of the bottles will serve as a stand for our future New Year's crafts.
	The next step is to roll the paper into a tube. Insert into the bottleneck...
	... and secure with tape.
	Now it remains to fix each tier of the tree with tape in a circle and a small New Year's craft: the tree is ready with your own hands!
	You can decorate the top of our Christmas tree with a homemade Christmas tree toy, or you can complete the Christmas tree the way we did.
	If you want to make a Christmas tree from plastic bottles more fluffy, like in the photo, when making a Christmas tree, the needles need to be cut as thin as possible (more often).
	By the way, the Christmas tree looks quite creative with larger “branches” - a master class from the Country of Masters website. We cut the bottle in the same way as in the previous version into 3 parts. Only cuts are made in a circle to the center, straight.
	In the center, a puncture is made with an awl and the needles are bent up and down in order. In the lid of a cream or mineral water, a puncture is made into which a skewer of the desired length is inserted.
	The parts are strung in descending order, a large bead is placed on top of the glue. The Christmas tree can be decorated with foam, rain, etc.
	Glue the Christmas tree to the stand from the disk. Christmas tree is ready!
	Nearby you can put gifts or plant an animal. Such Christmas trees have been a success for many years.

Materials and tools

In addition to bottles, you only need scissors and plastic rivet technology

plastic rivets

From the walls of such a bucket, you need to cut a ring, and cut the ring along the generatrix (necessarily only this way) into strips 2 ... 4 mm wide, 4 to 15 cm long. quantity.

Let's get started...

And if you insert a light-dynamic part (for example, a garland) inside the Christmas tree, then on New Year's Eve it will amaze those around you with its charm:

Here is such a master class. Of course, a little complicated, but what a beauty it turns out!

Soon the New Year 2018 will knock on all doors, and the houses will be filled with the smell of tangerines, vanilla and chocolate cookies, and pine needles. However, they won’t feel the unique aroma emanating from the green beauty somewhere: the owners of these dwellings, after watching videos and photos on the topic “how to make a Christmas tree with their own hands”, decide to save nature - not to buy cut down trees. Instead, they will make a Christmas tree at home from such improvised means as ribbons, balls, cones, paper, cardboard, cotton pads, tinsel. Even decorations for such a beautiful craft can be homemade - children will make them in labor classes at school and kindergarten. What else and how can you create a unique Christmas tree? Simple master classes with step-by-step explanations will tell you about this.

How to make a Christmas tree with your own hands at home to school or kindergarten

Surely, you will want to help your child in making his best Christmas crafts. To do this, first find and mark for yourself the most unusual ideas for creating a fluffy Christmas tree. Study carefully the master classes and photos on how to make a Christmas tree with your own hands at home at school or kindergarten. Bookmark the pages you have marked or print detailed explanations on how to create the craft on the printer.

Examples of Christmas tree crafts with photos and videos

If you have long been nurturing the idea of making a homemade Christmas tree instead of buying another felled tree for the New Year, read how you can make a Christmas tree yourself at home - bring it to school, kindergarten or decorate your house with a green beauty. Pay attention to our selection of photos and videos - the materials will tell you what and how to make crafts from.

How to make a Christmas tree out of paper with your own hands in a kindergarten - DIY crafts master class at home

Preschool children are not yet too deftly able to handle scissors and carefully connect the details of crafts. As a rule, a teacher or parents help children of this age to make something original. Having learned from us everything about how you can make a wonderful Christmas tree out of paper with your own hands and take it to the kindergarten, having studied the master classes of crafts for creating a mini-Christmas tree at home , moms and dads will be able to explain to the children what needs to be done in order for the craft to come out neat and beautiful.

Examples of homemade Christmas trees made of paper and cardboard

Making paper crafts requires accuracy and patience. Learn how to make a Christmas tree out of paper with your own hands in a kindergarten - a crafts master class at home with photos will tell you all the steps step by step.

Paper Christmas tree toy for the Christmas tree - Master class with explanations on the photo

To create this mini-Christmas tree, a New Year's toy, you will need to carefully study the photo explanations of the master class.

Fold the green square of paper in half twice and unfold it - you will see the fold lines.
Start folding the figure, focusing on the fold lines.
Consistently follow all the steps shown in the photo.
Cut off the bottom part of the workpiece.
Make symmetrical cuts on both sides of the workpiece - you will have a Christmas tree!

How to make a Christmas tree with your own hands at home to school for a competition - Master class with instructions

On the eve of the upcoming New Year, schoolchildren often make crafts for the holiday. At a certain time, all finished products are exhibited for demonstration to other students so that they can objectively name the best of the works. Of course, every child wants his craft to be recognized as the most original and beautiful. To do this, learn how to make a Christmas tree with your own hands at home to school for the competition - a master class with instructions will explain everything step by step.

Do-it-yourself felted wool Christmas tree - Master class with explanations

If you want to learn how to make felted crafts, read how you can make a Christmas tree from wool with your own hands at home and send it to school for a competition: a master class with instructions with a photo is attached.

Having bought green wool for felting, wind a tight cone out of it.
It is necessary to separate the wool from the skein by tearing it off, not cutting it off.
Putting the cone on a wet sponge, start felting it. A pen with a needle attached to it can help.
Constantly rotating the workpiece, moisten the future Christmas tree in warm soapy water and wring it out a little (be careful - otherwise the craft will lose its shape!)
Put the craft on a wet bag and, rotating it, roll on - this way the Christmas tree will be stable.
In the same way, make balls for the Christmas tree.
Carefully sew the balls onto the Christmas tree.
If desired, the Christmas tree can be decorated with a garland. Wrap diagonally around the craft, securing the “garland” of beads or beads with a few stitches.
To decorate the Christmas tree, you can use bells, beads, jewelry, etc.

How to make a Christmas tree from cotton pads with your own hands at home: crafts master class

A good master with a rich imagination will always have the most unusual, creative crafts in the house, made from unexpected, unusual materials. Such a craftsman can happily teach you how to make a Christmas tree from cotton pads purchased at a regular supermarket with your own hands at home: a crafts master class and photos are attached.

Master class crafts "Herringbone" made from cotton pads

Learn how to make a Christmas tree from cotton pads with your own hands at home: a crafts master class will teach you how to make it step by step. The snow-white beauty will decorate any New Year's interior.

So, prepare first:

Cotton pads;
stapler;
silicone adhesive;
Cardboard;
Scissors;
beads;
Green paint.

Prepare each cotton pad as shown in the photo: fold it twice in half and secure with a stapler.
For a Christmas tree 45 cm high, you will need more than three hundred prepared cotton pads.
From a thick sheet of cardboard, glue the cone, cutting off everything superfluous at the bottom. Start gluing the prepared disks to the cone.
Move from below, gradually attaching cotton pads in a circle.
The cotton tree for the New Year 2018 is ready and waiting for its outfit.
Glue beads to the center of some of the folded disks, and cover part of the “paws” with green paint.

How to make a Christmas tree from threads with your own hands at home: a master class in stages

As you already understood, crafts can be made from almost any materials and improvised means. The main thing here is not what the thing is made of, but the creative approach of the craftsman. Learn how to make a Christmas tree from threads with your own hands at home: a step-by-step master class, with the help of photos and explanations, will help you master this technique.

Craft "Christmas tree" from threads - Master class with photo

Read carefully how you can make an openwork Christmas tree with your own hands from simple threads - this is easy to do at home. A detailed master class will explain to you step by step how to work with materials, so that in the end you get a light, patterned Christmas tree.

First prepare all the necessary materials (see photo).
Make a cone out of paper by making cuts at the bottom. Through these cuts, you will wrap the Christmas tree with threads like a cobweb.
Having diluted the PVA glue in a bowl to the state of liquid kefir, moisten the threads in it and wrap them around the workpiece. Threads can be of different colors.
After finishing the winding, wait for the craft to dry. Gently pull out the cone from the inside - you will see a dense openwork Christmas tree. If you place a garland inside it, the tree will shine with New Year's lights.
If there is no garland, decorate the craft as you wish.

How to make a Christmas tree with your own hands from tinsel: photo and video instructions

It is customary to decorate houses, carnival costumes and ready-made Christmas trees with tinsel. And is it possible to make them something? About, how to make a Christmas tree with your own hands from tinsel, they will tell you the photo and video instructions of the master classes posted on this page. You will only have to repeat the actions of the craftsmen.

Big green Christmas tree made of tinsel - photo with explanations

If you decide not to buy a cut Christmas tree for the New Year 2018, find out how you can make a fluffy Christmas tree with your own hands from tinsel: in the photo and video instructions you will find all the explanations regarding this creative work.

How to make a Christmas tree with your own hands from improvised means - Master class with photo

Surely, every housewife has countless ribbons, beads, ropes, pebbles, scraps of material, broken jewelry and a lot of such nonsense in wardrobes and chests of drawers. Throwing all this away can be very pitiful, so read how to make a Christmas tree with your own hands from improvised means - a master class with a photo of the finished craft will give you the best tips.

Christmas tree from ribbons for the New Year 2018 - Master class with instructions

If you already know roughly how you can make various beautiful Christmas trees with your own hands from improvised means, pay attention to this master class with step-by-step photos on making a green Christmas tree from satin ribbons.

For work you will need:

Satin ribbons in three shades of green;
Green cardboard;
Glue,
Scissors,
Simple pencil;
Thread,
Burner;
Glass,
ruler made of metal;
Compass,
Silver and red beads.

Using a burner and a metal ruler, prepare pieces of satin ribbon 10 cm long. Protecting the table, cover it with glass.
You should end up with several tens of ten-centimeter pieces of ribbons of different colors.
Make loops from the ribbons, again using the burner and a metal ruler.
You should have three groups of loops of different shades of green.
From green cardboard, make a cone blank by drawing it as seen in the photo.
Using a compass, make more arcs, already smaller in diameter.
Starting from the bottom, glue loops of ribbon in rows in a circle.
At the top of the cone, the loops must be attached as tightly as possible to each other.
Alternate loops of different shades of green.
Start gluing beads to the ribbons.
As a result, you should get such a green beauty.

What you can make a Christmas tree with your own hands: Christmas crafts from cones

Going for a walk in the forest, collect the cleanest, neatest cones and other natural materials there - you will need them to prepare for the New Year holidays. What you found will be what you can make a Christmas tree with your own hands: a New Year's craft made of cones will surprise your guests with the originality of its appearance.

Topiary tree made of cones: a master class with photos and instructions

When you find out what else you can make a Christmas tree from with your own hands, you will definitely want to make this New Year's topiary craft from cones.

Before work, prepare all the materials and tools shown in the photo.
Using heavy scissors, cut off their “leaves” from all the cones collected in the forest.
Buy a ready-made cone or roll it out of thick cardboard. Starting from the bottom, move in a circle, attaching “petals” of cones to the base of the future spruce.
The future Christmas tree itself will soon begin to resemble a huge cone.
Having reached the top of the cone, form a neat top of the spruce.
Now begin to cover the almost finished Christmas tree with glue and sprinkle with sparkles.
If desired, cover the craft with gold paint.
Such an unusual Christmas tree-topiary will perfectly fit into your New Year's interior.

What to make a Christmas tree for crafts for the New Year 2018 and how to decorate it

Photo and video examples of Christmas tree crafts for the New Year

From what home masters do not try to make a Christmas tree for crafts for the New Year 2018, how diligently they decorate it! Newspapers, magazines, packs of souvenir money, plastic bottles and cups, peas, pasta, socks, notebooks, tinsel, balloons and much more are also used. The photo shows how creatively the creators of the most creative Christmas trees approached the work.

How to make a Christmas tree with your own hands from plastic bottles - a master class with photos and videos

Sometimes we don’t even realize how much unique craft material we have at home! If you and your children often buy bottled water, kvass and lemonade, learn how to make a Christmas tree with your own hands from plastic bottles - a master class with photos and videos will help you with this.

Homemade Christmas tree from plastic bottles - Master class with photo

Having learned how to make an unusual light Christmas tree with your own hands from plastic lemonade bottles and having studied this master class with photos and videos, you can easily replace the best replacement for a tree cut down in the forest. Of course, before starting work, it is worth preparing everything you need in advance, namely:

A large number of plastic bottles;
Frame for spruce (from PVC pipe or wooden slats);
wire;
Three cans of green, and one can of silver paint;
Stationery knife;
Scissors;
Drill or thin drill;
electrical tape;
Spruce stand.

Assemble the frame for the tree. Attach plastic corners to a piece of PVC pipe. They will serve as the basis for the side paws of spruce. On top of the "legs" (they do not touch the floor!) And in the middle of the pipe, make holes by passing the wire through them. Secure it with pliers. Fasten the cut-off top from the plastic bottle between the "legs" - this way the construction will be stronger. Reinforce everything with duct tape.
Cut off the bottom of the bottles.
Cut the rest of the bottle into "noodles".
Manually bend the strips away from the neck.
Bend the strips up, cut off the necks of the bottles and paint the blanks with green and silver paints. You can do without paints, initially using multi-colored bottles.
Start assembling the Christmas tree by stringing the blanks upside down onto the base. Screw the covers onto the lower legs. Drill holes in them and, with the help of a wire stretched through the hole, fix the structure.
Secure the top of the spruce with wire.
Place the tree in the stand. Decorate it with silver paint and tinsel.