How to hang wallpaper in the corners of a room. How to properly glue wallpaper in uneven corners of the room, saving money and nerve cells. Inner corners: features of wallpapering

Very often, in houses with relatively even walls, the corners have certain defects, therefore, before gluing the wallpaper in the corners, it is necessary to align them.

If this is neglected, then the facing material will lie unevenly, which will spoil the appearance of not only the walls, but the entire room.

Today, to create a beautiful interior, various types of roll finishing material are used.

They differ from each other not only in color performance, but also in the material of manufacture.

Every year, non-woven and vinyl wallpapers are becoming more and more popular.

They are considered environmentally friendly, so they are often used in bedrooms and children's rooms.

And thanks to the excellent resistance to high humidity and easy maintenance, walls in kitchens and corridors are often pasted over with this material.

Substrate preparation for wallpapering

Non-woven and vinyl wallpapers, unlike paper ones, are quite expensive, so they are not glued for 1 year.

In order for the roll material to lie flat and not peel off over time, a number of preparatory measures should be carried out, which include the following steps:

• dismantling of the old finish;
• plastering;
• puttying.

Before you start gluing exterior or interior wallpaper in the corners, you need to remove the old finish.

If this is not done, then after a while bubbles and wrinkles form under the new wallpaper.

And if thin paper wallpapers are used for gluing, then the pattern of the past cladding may appear on them.

Dismantling of old wallpaper is carried out with an ordinary kitchen knife or spatula.

If during the work there are difficulties in peeling them off, then the finishing surface can be treated with heated water and wait 10-20 minutes until the material gets wet.

The next step is to level the walls and corners with plaster.

It is applied in layers.

The thickness of one layer should not exceed 6 mm.

At the same time, the number of such layers depends on the degree of unevenness of the walls.

At the last stage, puttying is carried out, with the help of which the finishing surface will acquire the required smoothness.

For this, 2 types of putty are used: starting and finishing.

The second one is more saturated white and less grainy.

After the final layer of putty dries, the walls must be cleaned with sanding paper to remove minor defects.

After sanding the walls, they are primed again.

At the same time, special attention should be paid to the corners, since these places are most exposed to moisture and microbes.

Gluing inside and outside corners

Non-woven wallpaper is "more obedient" than paper, so it is easier to work with them.

Before gluing wallpaper in the corners, it should be understood that one type of glue is used for ordinary roll material, and a completely different one for non-woven wallpaper.

Therefore, the choice of one or another adhesive composition will depend on the type of wallpaper used.

At the same time, with paper wallpaper, glue is applied both to the finishing surface and to the wallpaper itself, and with non-woven and vinyl wallpaper, only to the wall.

The technology of gluing the outer corners is somewhat different from the finishing of the inner ones.

How to glue the inner corner?

So that after the wallpaper dries, wrinkles do not form in the inner corners, pasting should be done not with one solid canvas, but with two: on each side of the canvas.

To do this correctly, you first need to measure the height of the wall, along which to set aside and cut off the required length of the canvas (wall height plus 20-30 mm for allowances).

Then, immediately before gluing, the wallpaper must be bent lengthwise into two parts: one part (main) will cover one plane of the corner, and the second (about 40 mm wide) will go to the adjacent side.

This should be done very carefully so as not to inadvertently damage the non-woven or paper wallpaper.

After that, using a roller or rag, the canvas is smoothed with smooth movements from top to bottom.

In this case, you need to carefully watch so that air bubbles do not form under the wallpaper.

The next step is pasting the second side of the corner.

This is done with a slight overlap (about 25 mm), on a previously glued canvas.

Then, at the mark, with the help of a clerical knife, 2 layers of wallpaper are cut simultaneously, after which the excess parts are removed.

If this procedure is done correctly, then you will definitely like the result of the work.

How to glue the outer corner?

If the outer corner is sufficiently even, then you just need to wrap the canvas and continue finishing.

If you have a curved protrusion, then wallpapering is overlapped.

To do this, the canvas is first glued to one side of the corner, with a small margin (25 mm), which will go to the second plane.

If the wrapped edge lies with folds, then it can be cut in 3-4 places.

After that, as in the previous case, the stock is cut along a plumb line, as close as possible to the ledge.

As a result, you will get only a slight overlap, which will practically not be visible.

Sticking wallpaper in the corners is a rather complicated procedure that requires patience and accuracy.

However, if you approach the work with full responsibility, taking into account all the rules and wishes, you can be sure that the result will be no worse than if a specialized team glued paper or non-woven wallpaper.

The use of roll materials for surface cladding is a popular and sought-after solution that allows you to achieve high-quality results in a short time. But the finishing technology has some nuances. It is especially difficult to glue wallpaper in the corners: the resulting coating must be free of distortions and defects. The most suitable method is selected depending on the situation.

Existing varieties have a certain order of wall cladding, which allows you to achieve the best result.

Vinyl

The technology for working with this option is not very difficult if you perform all the processes correctly.

Step-by-step instruction:

1. The place is being prepared. For convenience, the material is rolled out on a clean floor or a table of a suitable size with a pattern down.
2. Trimming is carried out taking into account the allowance of 100 mm. If the coating has a complex pattern, then the scheme specified by the manufacturer is used.
3. The canvas is treated with glue and folded in half for better penetration.
4. The composition is applied to the wall with the capture of areas that extend beyond the width of the roll.
5. The strip is laid on the base and smoothed out well.
6. It is taken into account that standard and meter vinyl wallpaper on a non-woven base can only be glued end-to-end, the overlap will spoil the look.

The vinyl layer on the canvas is strong enough, so the wallpaper can be safely smoothed out with a wallpaper spatula without fear of damaging the integrity.

On a note! In the absence of experience and the need to adjust a complex pattern, it is better to prepare: for this, the strips are placed on a horizontal surface, aligned with each other and the size of the necessary adjustment is noted.

Paper

Sticking this variety is rarely accompanied by difficulties. For the process, you can use any glue, including those prepared by yourself.

Action algorithm:

1. According to the width of the roll, marking is carried out using a level and a plumb line.
2. The material is dissolved into strips, depending on the pattern. For this, a technology similar to working with a vinyl version is used.
3. The canvases are well smeared with the prepared composition and rolled up.
4. After surface treatment, pasting is carried out. The excess is cut off.
5. Most often, paper products are overlapped, but strips can also be joined. It is taken into account that after drying the canvas will become narrower, so a special paper tape is placed under the seams. This rule applies to other types of wallpaper as well.

It is impossible to tighten the web at the junction by force, the connection is leveled exclusively with a rubber roller

All processes, especially smoothing, are carried out with care, because even multi-layer products are very easily damaged.

non-woven

To glue this variety, a special version of glue is used, since the material is quite heavy. The preparation of the binder is carried out strictly according to the instructions and is applied only to the wall.

Process diagram:

It is important to properly impregnate the base: do not leave dry areas. Be sure to affect places that go beyond the width of the canvas.

Advice! To speed up the process, it is better to apply the composition with a roller.

In addition, we suggest watching a video where the process of gluing non-woven wallpaper is considered.

How to properly wallpaper corners

The technology of laying sheets on the outer and inner corners has differences.

External

These areas are the most visible, so they must be glued with special care. The easiest way is if the angle is perfectly even, but this is quite rare.

In the presence of defects, the process is complicated. If the corner is littered, then it will be necessary to trim the canvas along the bend line in order to impose one section on the adjacent one. This method is not suitable for varieties with complex patterns.

There is another way:

1. The strip is glued to a section of the wall.
2. Using a special spatula, the material is carefully smoothed under the existing bend, a transition is formed.
3. If required, part of the laid canvas is torn off, after which the excess is driven up or down. There must be a margin on both sides.
4. To adjust the pattern in case of skew, the next strip is overlapped until the pattern is aligned with an indent from the edge of 5–10 centimeters.
5. With the help of a ruler, which serves as an emphasis, the superimposed canvases are cut exactly according to the pattern.
6. If required, the joined sections are additionally coated with the composition.

Docking an outer corner with trimming on one of the adjacent planes is considered the most effective way of arranging

This method does not completely correct the skew, but facilitates further sticker and fitting.

Interior

The technology for working with such a site is almost identical to the previous process, but has some nuances:

1. All sides are well treated with wallpaper glue. If the composition is also applied to the canvases, the impregnation must also be sufficiently thorough.
2. Laying begins with the wall from which the movement is carried out. The first fragment is aligned with the previous one, smoothing into a corner is carefully performed. To do this, with a rubber spatula, the waves are driven in one direction.
3. The part that falls on the adjacent wall is slightly pressed.
4. The next steps depend on the situation. Most often, it is required to cut off the existing bends in the middle and put the excess on top of each other.
5. To achieve better alignment, the edges are shortened and smeared, after which the segment is located on the main part of the canvas.

Technically, joining an internal corner is not much different from similar work on external structures, but this process is considered easier, since internal corners are visually less noticeable.

This technology allows you to glue different types of products, but if the angle does not involve trimming, laying is carried out in a standard way. To do this, the joint of both sides is carried out with a margin in order to level the unevenness by fitting and trimming at the place of alignment. This will take longer, but will get rid of the overlap in the corner.

Video tutorial: how to glue wallpaper with trimming in the corners

Docking wallpaper with a pattern

Work technology:

1. The strip is laid on the initial part of the wall and gradually distributed over the surface. Waves are driven towards the corner.
2. The material is carefully fixed on the inner fragment and smoothed from top to bottom. It is taken into account that the canvas should be cut off with a significant margin, since trimming of the lower and opposite edges will be required.
3. The part that falls on the perpendicular wall is distributed. The areas at the skirting boards are adjusted.
4. If the side is uneven, then it must be pasted over with the next strip, which lies completely in the vertical plane. The offset must affect the matching pattern.
5. A ruler is set exactly along the line, with the help of a clerical knife, the excess is cut off.
6. The second strip moves to the corner, the gap needs to be additionally glued.

If there are no problems, you can dock directly along the inner corner, but this will require a certain level of skill.

Wallpapers with a pattern are joined according to the same principles as without a pattern, but if you stick a horizontal mark from masking tape on adjacent canvases in advance, then it will be easier to combine the ornament

What to do if the joints are crooked

Perfectly even corners in rooms are rare, so to eliminate various problems, you can use the recommendation that many designers use - a combination. It is necessary to seal the transition from wall to wall with wallpaper with a pattern or with bright colors. Part of the pattern should go to the adjacent side, where it is cut at a right angle and combined with a solid material. The docking line will turn out to be even, and the existing shortcomings will not be evident.

Wall decoration with wallpaper is the most popular option for decorating walls in rooms. Undoubtedly, wallpapering on even walls is quite elementary and requires only a little skill, but wallpapering the corners of a room is technically more difficult. Before sticking wallpaper with your own hands, you need to properly prepare the walls.

First you need to clean off old wallpaper or paint, apply primer to the walls and level their surface. And only then begin to paste over the corners with wallpaper.

So, repair specialists distinguish the following stages of this process:

1. You need to start by leveling the corners, for this you can use putty and, after it dries, clean it with sandpaper. In order for the angle to be even, you can use a special device - a plastic corner, which is attached to the putty. Remember that if you do not get rid of uneven surfaces, the wallpaper may peel off.
2. The next step is to apply glue - before gluing the wallpaper into the corner of the room, you must very carefully glue the entire height of the corner with glue. If the roller does not cope with its task and leaves unsmeared fates, it is worth using a brush.
3. Direct wallpapering of corners with wallpaper - there are different lessons of specialists that help to properly wallpaper the corner of a room, it is worth listening to them, but for greater productivity, we will outline some of the features of this stage: competent finishers do not recommend gluing wallpaper in the corners with whole strips, this is due to the fact that they can distortions will appear and the joints will be uneven.
4. The wallpaper canvas must be cut so that their side from the sides extends 50 mm onto the adjacent wall.

Glue must be applied to the strip of wallpaper and the corner of the wall. Next, you need to attach the wallpaper to the corner of the wall as follows - if the pasting process starts from left to right, then the left side is applied to the inside of the corner to evenly cover it.

At this stage, you need to clearly understand that you need to wallpaper the outer and inner corners in different ways.

outside corner

External corners can be glued in two ways: firstly, if the outer corner has a flat surface, you can not waste time on leveling it and immediately apply wallpaper to the corner, then use the level and measure the edge of the strip so that the remaining strips lie evenly; secondly, to glue the outer corners, you first need to lead the strip around the corner by 4-5 cm, and glue the next part of the wallpaper at the top. Using a clerical knife and a ruler, cut these layers vertically.

Inner corner

Internal corners require more attention. Wallpaper must be glued so that they go onto the adjacent surface by about 3 cm, but not more, otherwise they will go wrinkled. The fold and turn of the wallpaper must be coated with glue. Next, you need to measure the width of the wallpaper located on the adjacent wall, mark the allowance of the glued side, which is glued at a distance of about 2 cm from the corner and a vertical line is drawn through it with a plumb line - this will mark the edge of the glued wallpaper.

Alignment of the wallpaper is done by rolling, for this there are special rollers and spatulas.

All the above stages of wallpaper stickers in the corners go sequentially.

Corners on the walls on the wallpaper: what is it

Plastic wallpaper corners are a good finish for finishing corners - they have protective functions and give the corner a finished look.

Construction markets offer different decorative corners:

• Corners with a width of 20 × 20 to 50 × 50 mm are suitable for corners that are subject to heavy wear;
• Dimensions 10 × 10 or 15 × 15 mm will give a neat finished look to the wall - they are called decorative corners;
• The corners may differ in color, may have the texture of wood or metal.

For arched outer corners, it is better to use corners with the following approximate dimensions: 5 × 17.7 × 17.10 × 20 and 15 × 25 mm. Plastic corners are recommended to be mounted with silicone sealant, it is colorless and has good adhesion. The length of the corners varies from 3 to 7 m, so it can be adjusted to individual sizes.

Plastic decorative corners help protect wallpaper from mechanical damage at the corners of the wall, in addition, they are not expensive and easy to install.

How to glue wallpaper in non-woven corners: features and tips

Non-woven wallpaper is particularly durable, but working with them is quite difficult, especially on corner surfaces, because. they are not elastic.

To paste over the corner of the wall with such wallpaper, when cutting off part of the wallpaper, it is necessary to make an allowance of 1.5 cm, this allowance must overlap.

You need to know a little secret - sticking non-woven wallpaper will be easier if you make equal cuts along their entire length along their edge.

Glue in this case is applied only to the wall, and the wallpaper must remain dry. In the work on decorating the corner with such wallpaper, it is better to first use the corner, then unnecessary crooked places will not appear. If the choice is made in favor of wallpaper with a pattern, in this case it is necessary to qualitatively adjust the pattern in the corners. In order to keep the pattern in the corners intact, you need to cut the next strip from the corner to fit the pattern of the already pasted wall.

Here are some tips:

• It is necessary to make a small overlap on another wall;
• It is better to hide the joints at the top of the corner;
• Wallpaper with a pattern in the corners is better to glue on a plumb line.

Meter wallpaper is a wide non-woven fabric a little over a meter. This type of wallpaper helps to quickly paste over a large apartment and the selection of a pattern becomes easier. In order to stick meter-long wallpaper in the corners, you need to overlap up to 3 cm on the next wall. The rest of the procedure will not differ from the standard pasting of corners, which is described above.

How to glue corners on wallpaper: installation technique

Then proceed according to the following plan:

1. The adhesion of the corners to the wall will be stronger if they are glued to the wall, and not to the wallpaper;
2. Distribute adhesive material evenly on the inside of the corner;
3. Attach and press to the desired area on the wall, remove excess glue with a napkin;
4. Do not touch the corners until the material is completely dry.
5. In order for the sealant to better grab on the site, you can fix the corner with adhesive tape.

How to glue wallpaper in the corners (video)

So, knowing the technology of gluing wallpaper in the corners, you can make high-quality repairs with your own hands and, in addition, help your relatives in this difficult task.

To date, the most popular method for decorating walls is wallpapering. As it may seem at first glance to a novice master, the step-by-step instructions are simple, so many apartment owners decide to stick wallpaper with their own hands, not knowing the specifics of the work. As a result, the fit of the canvases is incorrectly formed, irregularities and other shortcomings are noticeable, which reduce the life of the finish.

If the house has even, properly prepared walls without defects, it’s really not difficult to start sticking wallpaper. But, few people know how to properly glue the wallpaper in the corners, observing the pattern, so that it looks beautiful and neat. In this case, you need to know about the techniques, without the use of which you should not start gluing wallpaper at all.
Next, we will talk about different ways to properly glue wallpaper in the corners of a room, we will give video and photo tutorials that will help you save money and complete a beautiful design of a kitchen, corridor or hall on your own.

What problems can you face?

Ideally, in order not to cut the strip at the junction, the corner in the room should be perfectly straight and vertical. In this case, it will not be difficult to glue the wallpaper, all work will be reduced to a continuous operation, which consists in processing the wallpaper and walls with glue and fixing the canvas.

But, far from everyone can boast of perfectly even corners in their home, so at least one corner will be uneven and cause difficulties. At the same time, the appearance of the first pasted wall will be vertical, and the joint of the canvases and the subsequent transition to another surface will become more and more distorted. This will lead to the fact that the subsequent selection of the pattern will be impossible.

Corner preparation

If the corners seem to be absolutely even, before sticking the wallpaper, it is enough to walk on them with fine-grained sandpaper or a dense hard cloth to remove barely noticeable defects and remove debris and dust.
But, if the corners are noticeably crooked, have protrusions or, conversely, cracks and niches, they must be leveled with putty. If the damage is very large (for example, there are falling pieces of the wall), it is appropriate to use plastic corners.

Take note! Before sticking wallpaper, consider the following features:

• no need to paste over the corners with a whole sheet of wallpaper;
• do not glue the wallpaper end-to-end in the corners.

If the corner is glued end-to-end with canvases, it will not be possible to avoid ugly cracks. Also, unevenly laid wallpaper in a corner will distort the whole picture and the overall vertical. The best option is to overlap the wallpaper, but please note that an overlap that is too wide is unacceptable, its optimal width should not exceed 1-1.5 centimeters.

Features of work depending on the type of wallpaper

An equally important point that needs to be taken into account before pasting the walls is the material from which the canvas is made, because different materials require a different approach to work. How the type of finishing material affects the technology for forming corners, see the table below.

Variety of wallpaper	Features of the work
Paper	The paper roll of wallpaper, which does not have complex additives, is the most demanding. You need to work with such wallpaper as quickly as possible so that the material does not absorb excessive moisture from the glue. If you overexpose the panel treated with glue, you risk that it will spread in your hands on the klapti.
Vinyl	How to glue vinyl wallpaper on a non-woven base meter in the corners depends on many little things. Before applying glue-treated wallpaper to the wall, they need to be allowed to soak. Note that some types of vinyl wallpaper can be covered with a gentle coating, which can only be worked with a rubber roller with a working canvas. Since such material is very heavy, the corners must be carefully opened with glue to ensure sufficient adhesion of the material to the wall.
non-woven	How to glue non-woven wallpaper in the corners, and in general on the wall, is a little different from working with paper varieties. They do not need to be treated with glue, it is enough just to coat the wall. In order to fix the edge of such a canvas well, just before the formation of an overlap in the corner, the wallpaper must be additionally smeared with glue.

Please note that the thicker the wallpaper is used, the smaller the overlap needs to be formed.

How to glue wallpaper in the corners (video)

Wallpapering inside corners

The goal of high-quality wallpapering is to ensure that “wrinkles” do not form during work, and there is no gap to the plinth between the panels. To achieve this, you need to start a strip of wallpaper so that the grip on the wall in the neighborhood does not exceed 2 cm. To do this, it is important to consider how strongly the angle is curved, because the greater the deviation from the norm, the more you need to form an allowance.

It is very important to press the wallpaper against the wall as hard as possible. If you have formed "wrinkles" from this, you can slightly reduce them (sometimes even completely remove them) by cutting the wallpaper in the direction of the formed wave. Since the beginning has been made, now it's time to apply the markings, adhering to which the second strip will fit. To do this, it is necessary to set aside the width of the wallpaper, reduced by 5 mm, from the overlap of the first strip, which was launched onto the adjacent wall. Then you need to set aside the vertical with a level and glue the second strip.

How to arrange outer corners?

To form an outer corner, you need to designate a point that will be the start of the wallpaper sheet so that it goes around the corner by 3 cm. The edge of the cloth must be carefully fixed to the wall, and if “wrinkles” form, you can remove them, as we described above in the article.

On the edge of the canvas, which is laid on the adjacent wall, tear off a thin ribbon of wallpaper so that there is a small edge in the remainder. Such actions will allow you to remove excess volume from the seam, making the overlap less noticeable. Then, using the level, you need to set aside the distance from the corner, which is the width of the wallpaper sheet, plus 6mm. Along this line, you can glue the next strip of wallpaper so that the edge of the new canvas overlaps the edge that was previously wound on the wall. Applying force and firmly pressing the joint, trim the wallpaper, and treat the joint with a rubber roller.

Photo gallery of finished works

Date: 05/13/2017

Many people who decide to make repairs in an apartment or house with their own hands believe that high-quality wallpapering will not be difficult for them. Yes, to some extent this finishing material is quite practical, but only on flat sections of the walls, which cannot be said about the corners. And how to glue wallpaper in the corners? This is the question faced by people who have begun repairs without professional help.

It is in the corners that gluing is a laborious process, which makes it difficult and calls into question the quick completion of the repair. So you should approach this issue with all seriousness and study with scrupulousness all the nuances of such an operation, because poor wallpapering in the corners can generally ruin the whole look.

How to glue wallpaper in the corners

Wallpaper is and remains the most popular material for finishing any kind of premises, whether it is a room in an apartment, an office, or a beauty salon. The quality of the wallpaper varies, and you can meet absolutely every taste, color scheme and cost.

Sometimes cheap nondescript wallpapers transform a room so much that they seem almost as good as expensive ones, that is, now the range of wallpapers on the construction market is different, and there is a high-quality and at the same time cheap material - two in one.

Today, in order to paste wallpaper, you do not need to have professional skills, but you need to know the pasting system. The walls must first be aligned along the perimeter, in the corners, and from here problems begin for non-professionals.

Wallpapering in the corner

It is not recommended to glue a single strip of material. In the presence of uneven corners, the strip lies in folds and does not converge with the other. We recommend leaving a protrusion around the corner by 1.5 or 2 centimeters and then the strip will lie flat. Having chosen a wallpaper with a high density, use a plumb line. Glue part of the cut wallpaper with a small overlap on the adjacent wall so that it is as vertical as possible.

If there are switches, sockets in places of corners or in proximity to them, before gluing and any construction work, turn off the electricity supply and remove the covers. Fully stick the material on the convex parts, and only then carefully cut it out by making small cuts.

When starting to paste over the wall near the door, it is important to know that the strip of wallpaper must be cut vertically before the beginning of the frame. Then it is attached along the edge of the wall. Wallpaper protrusions should be cut off.

Non-woven wallpaper - how to glue wallpaper in the corner

Wall preparation

Wallpapering should be carried out in accordance with the existing technology, observing the sequence of processes, which applies not only to the corners, but in general to the entire procedure for pasting walls with flashing.

List of the sequence of stages of finishing work for wallpapering:

1. Clean the walls of oil paint;
2. If there is whitewash, then clean it off;
3. Remove deep irregularities, especially in corners;
4. Carry out the preparatory work. Surface primer.

It is better to prime the surface with professional tools that are sold in containers of various prices, but can also be primed with diluted glue, but not particularly welcome. A special roller or a wide brush will help you prime the surface. Due to the fact that pasting is especially difficult in the corners, there is such a nuisance as a pattern shift. On the walls, the geometry of the drawing was preserved, but in the corners everything went wrong and now spoils the general background. Therefore, most responsibly approach the inspection of the corners, whether there are irregularities, eliminate them if any.

Preparing walls for wallpapering

Stage alignment of the corners of the wall

After you have pasted over all the smooth surfaces of the walls, you have to move on to the corners. Now inspect, and noticing irregularities, proceed to grinding - carefully puttying. After the putty is completely dry, it is necessary to clean the entire surface with sandpaper to achieve a perfect smooth surface so that the wallpaper does not peel off in the future.

Now the corners need to be coated with a primer. If you do not have the skill of puttying, then there is a way out, just buy the same type of wallpaper, or with a simple pattern that does not require further joining (paper). So part of the question of how to glue wallpaper in the corners can be considered disclosed.

The stage of applying glue in the corners

After leveling the surfaces in the corners, we proceed to the application of glue, it must be distributed with all care along the height of the walls, and in the corners most conscientiously, because in these places the wallpaper is most often peeled off. With a roller, we distribute the glue along the entire length and with a brush in hard-to-reach places.

Applying glue to wallpaper and walls

How to glue wallpaper in the corners

Finally, we moved on to the important part of the issue of gluing in the corners. The pros of this business recommend gluing a piece of canvas in the corners, even if the whole piece is perfectly straight. This can be explained by the fact that there is a high probability of distortions in the corners, and the subsequent sheet does not fit at all, and after drying, folds can be found. Room decorating professionals advise cutting wallpaper canvases so that the side side goes to the next wall by 50 mm. Below is a picture of wallpapering in the outer and inner corners.

Did you know: a nuisance for beginners in this matter is the curvature of the gluing areas. Such a defect in the eye surface cannot always be detected, so a list of tools will come to the rescue: a plumb line and a building level. They measure the corners before wallpapering.

If there is a quite serious "blockage", then it is better to come to the method of "cutting" in these places. This method is used for thick wallpaper - vinyl.
According to this method, the material is passed 50 mm to the adjacent wall around the corner, and the next sheet is glued with an overlap.
The next step: in the middle of the corner, a vertical cut is made through two layers of wallpaper with a special construction knife under the level or ruler in the direction from top to bottom.

The scheme of wallpapering in the corners

During the whole process, the iron ruler must fit snugly against the corner and be pressed strongly so that there is not the slightest movement. Otherwise, a shift along the cut sheet is provided. Masters recommend using a long metal ruler, a building level, which has more weight and produces a wonderful press that interferes with movement.

We glue wallpaper in the inner corners

To avoid the appearance of wrinkles in the inner corners, these canvases should be divided into two parts before wallpapering. The first step is to stick the material to the corner of the room, then you need to accurately measure the distance from the last piece of wallpaper pasted to the corner bend, and add 10-12 mm to the resulting figure. Next, one prepared part is glued to the wall with a cut edge at an adjacent corner. Adjust the edges as usual, be it top or bottom.
Now, using a brush or rag, press the wallpaper into the inner corner of the room. If irregularities occur, such as warping of the material, then take a special knife and make cuts, while pressing the wallpaper into the wall. Then glue the next part with an overlap on the glued material, pushing it tightly against the wall with a brush. Finally, cut off the remains at the bend with the same knife.

Tip: If your corner inner and middle parts have small bulges, and the bottom is littered a little inward, it is better to press the cut edges with an overlap. When pasting a room with thick (vinyl) wallpaper, the best option is to use glue with a transparent base at the junctions, such glue is suitable for dense materials.

Methodology for pasting the outer corners of the room

Gluing the outer corners of the room requires pre-calculating the length of the wallpaper, and so that the canvas is not only enough, but it can go around the convex part of the wall from 21 to 25 mm. When gluing dense quality wallpaper, be sure to make light cuts to smoothly lay the strip.

How to glue wallpaper in the corners correctly

So, on dense wallpaper, using an iron ruler and scissors, excess strips of material are cut off, leaving a minimum of an edge, the visibility of which will not be visible under the subsequent canvas. On top of everything, a subsequent strip is glued with an overlap of 5-6 mm. If you have chosen smooth wallpapers, then immediately iron them with a roller, and with a convex pattern, voluminous ones can be very slightly passed with a rag.

Wallpapering with a pattern in the corners

The vertical pattern of the wallpaper makes it difficult to stick in the corners, because in these places distortions are especially noticeable. A pattern with a horizontal position is no exception, for example, after gluing it can be completely skewed. To avoid such incidents, it is necessary to make a small overlap on the wall in the neighborhood and hide the joint at the top of the corner.

Tip: the difficulty of wallpapering corners is to follow the rule - the edge lay flat on a plumb line, and the other should be cut along the edge of the corner.

It is not possible for a non-professional to glue wallpaper and at the same time without pattern shifts without experience. The main thing is to make it less noticeable using the instructions provided above.

Repairing an apartment, house or office takes a lot of time and effort, as well as money, if you decide to turn to hired workers for help. But thanks to the instructions given to you above and following them exactly, you will be able to start finishing on your own, paying attention and time to studying wallpapering in the corners. Pay attention to the presence of defects, whether your walls are even, and carry out preparatory work to eliminate irregularities. In addition, radiators and pipes often pass in the corners, interfering with the pasting process, turning repairs into a hassle.

If you approach this task responsibly, taking into account all the recommendations and rules, then you will expect quite a wonderful result, no worse than if the gluing was carried out by a professional team of craftsmen. By doing the finishing work with your own hands, you will save a lot of money. Good luck, and have a good completion of repairs in your home!

How to glue wallpaper in the corner - video review