How to make a bottle cutter for cutting tape from plastic bottles. Cutting plastic bottles - how to make a device for cutting tape with your own hands Knife for cutting plastic bottles with your own hands

Plastic tape made of plastic bottles used in homestead farming. Thanks to it, you can strengthen a wooden fence or tie it up berry bushes. This rope can withstand up to 50 kg. It depends on its thickness and length. It is mainly used as a fixative.

There are two cutting methods plastic bottles: manual and machine. You can make transparent tape yourself at home. To do this you will need sharp scissors and proper markings.

Agree that the production of such material manually quite a labor-intensive process. A special device will help make cutting transparent tape easier.

What can a bottle cutting device be made from? What materials will be needed to build such a structure? The answers to these questions are presented in our article. Advice from experienced craftsmen will help you cope with the task.

Advantages of plastic tape

There are several positive qualities transparent tape in household. These include:

does not deteriorate when exposed to sunlight;
long service life;
resists low temperatures;
can withstand up to 80 kg;
low cost of material;
no odor;
decorativeness.

How to make equipment for cutting plastic tape?

The device for cutting plastic bottles consists of simple parts and elements. For this you will need:

wooden base. Its width must be at least 30 cm;
medium size washers 10 pcs.;
small diameter washer 4 pcs.;
drill 2 pcs. Its diameter must correspond to the size of the washer;
a small part of a stationery knife 10 cm;
screwdriver and wrench;
simple pencil.

Thanks to this machine, cutting plastic bottles with your own hands is fast and efficient, and the thread has a uniform texture. The process of creating equipment includes several stages:

On wooden base make markings to fix washers of different diameters. For this you will need a simple pencil. Using a screwdriver, make through holes at the marks.

The width of the plastic tape can be adjusted by moving the washers to the desired distance. Basically, this gap is 1 cm. A through hole is made on a stationery knife. It is placed on top of metal parts.

An additional nut will help connect the knife to the machine structure. In this case, you should not tighten it too much. This will create discomfort during the work process.

When the equipment is ready, it is checked for functionality. To do this, the bottom of the bottle is cut off and secured between the nuts. Now one edge is cut with a sharp knife blade, and the other is turned clockwise. The result is a plastic tape of the desired size. The photo of cutting plastic bottles shows the work process.

Metal cutting machine for plastic bottles

We bring to your attention another idea on how to make a device for cutting bottles. For this you will need:

a small piece of construction corner;
stationery blade 10 cm long;
small nuts 2 pcs.;
metal drill;
electric drill;
hacksaw.

Manufacturing process:

On the surface metal corner make a small through hole. Do the same with a stationery blade.

Having measured the width of the fixing nut with a hacksaw, make notches on the surface of the angle. In the future, they will help adjust the width of the plastic strip. The distance between each mark will be 1.5 cm.

The knife is fixed in the corner part of the metal base using an additional nut.

Pay attention!

Next, the entire structure must be secured to a solid surface. The production of tape from bottles is carried out by rotation plastic product clockwise. You should not make sudden movements. This may cause damage to the plastic thread.

Photo of cutting plastic bottles

Pay attention!

I have come across videos on the Internet many times about making fishing line/tape from a plastic bottle.

When I learned that the video “Bottle Cutter of Lawyer Egorov” had received more than 3 million views, I thought: “It’s probably a necessary thing in the household, since so many people are interested.” We need to check how that magic bottle cutter works.

Everything needed to make the miracle device was found at the dacha. Aluminum corner - 30 mm. A pair of short M5 screws with wing nuts. Long screw 80 mm, with nut. Blade for a stationery knife.

You will also need a drill with a set of drills and a jigsaw.

Drill holes to secure the blade.

Now we drill a hole for the long screw.

Use a jigsaw to cut off the excess.

Now we need to make two or three cuts through which we will pull the fishing line.

Now you can assemble the bottle cutter. We fix the knife blade with two screws. We install a long screw on which the bottle will spin.

First experiments

The wider the slot, the wider the line/tape. Apparently I didn’t guess some sizes; I couldn’t cut the thin ribbon. But the 5mm tape came out well.

Use scissors to cut the tail to the desired thickness.

We insert it into the slot and begin to carefully pull it out from the other side. The knife cuts the bottle, and the slot limits the width of the tape.

What to make from plastic tape?

The question of what to do with the tape now confronted me. I wrapped tape around the handles of old pliers.

We try to lay the tape evenly on the handle. At the end we slip it under the previous turn, tighten it and cut it off.

We warm it up briefly with a hairdryer. The plastic tape behaves like heat shrink: when heated, it shrinks, perfectly squeezing the handle.

It's probably better now.

My wife also tried tying the bushes with ribbon. I haven't gotten around to other ideas for using tape yet.

What else can be made from plastic fishing line? You can weave a stylish bag from ribbon. Make a plastic broom or brush.

For cutting tape from plastic bottles. I saw a video on the Internet where a kind of ribbon was made from an ordinary plastic bottle. The scope of its use is of course very limited.

I saw on the Internet where a kind of ribbon was made from an ordinary plastic bottle. The scope of its use is of course very limited.

Used during construction wooden fence, where he strengthened by tightening the place of the nailed board nail to a horizontal bar. In winter, this section of the fence was constantly swept away a large number snow, as a result, many boards flew off the fence, so to speak. I used ordinary iron wire before, but it quickly rusted and became unusable. Buying galvanized is expensive. The tension in the twine weakened over time. As a result, I began to tighten plastic bottles using tape and partially melt them after tying them to secure the connection. This structure stood successfully for one winter.

The method for producing tape from plastic bottles is surprisingly simple and accessible.

You will only need two M5 bolts (no more needed) with a length of at least 30mm, two nuts and washers for them, a wooden block or board, a stationery knife blade, and also several washers larger size, for example with a hole of 8 mm (their number depends on the thickness of the tape being cut).

First we put the washers large diameter in this case, on the block close to each other and mark the holes with a pencil.

We drill holes with a drill using a 5 mm drill bit.
Insert the bolts.

We insert large diameter washers in two pieces (the number depends on the thickness of the tape you need) so that there is a gap between them.

We insert the stationery knife as shown in the photo.

We put small washers in the bolts and tighten them with nuts (do not overtighten, otherwise the blade will burst).

Cut off the bottom of the bottle and make a small narrow cut in the form of a strip counterclockwise.

We insert the strip into the hole between the large washers of the cutting device and pull without jerking while holding the bottle with the other hand. Wood block I first secured it with a clamp on the table.

The tape did not always turn out to be uniform in width, but for me this was not so significant.

One of global problems The advice of society is waste disposal. Proper use of household waste will help you not only environment much cleaner, but also solve many problems without much effort and expense. We want to give you one of these useful tips how to properly recycle plastic bottles, and what can be made from them.

Plastic bottle tape:

You can make many useful things from a plastic bottle, and one of these simple crafts is a very strong ribbon.

Figure No. 1 – Tape from a plastic bottle

One plastic bottle will yield about ten meters of such tape (depending on the thickness). And you can cut such a tape not only with scissors, I recommend making you a special device, a machine for cutting tape from a plastic bottle.

Figure No. 2 – Machine for cutting tape from a plastic bottle

In order to make it you will need a paper knife blade, a wooden stand, two bolts, two nuts and about fourteen wide washers.

First you need to mark your platform, to do this, attach two washers (leave a gap of about two millimeters between them) and drill holes with a suitable drill.

Figure No. 3 – Marking the workpiece

Figure No. 4 – Drilling two holes

Then we insert the bolts into the hole and put on a couple of washers (by the number of washers you put on you adjust the height of the knife and thereby the width of the resulting plastic tape).

Figure No. 5 – Insert bolts into holes

Figure No. 6 – We put washers on the bolts

Figure No. 7 – Putting the blade on the bolt

Be careful, the blade is very sharp, don't cut yourself! Having put on the blade and installed it in such a way that it can be clamped with washers, put several washers on top of each bolt (five pieces)

Figure No. 8 – Fix the blade with washers and tighten the nuts tightly

I had washers of a narrow diameter, and I didn’t want to break the blade of the knife, but in general I recommend taking a narrow blade and wide washers so that it would be well hidden there and you wouldn’t cut yourself on the blade. And also remember that the nuts must be tightened very tightly so that your blade does not tear out!

Everything is done very simply, you just need to cut the bottle and pass it through the blade.

Figure No. 9 – Passing the bottle through the blade

Figure No. 10 – Pulling a bottle through the machine

Figure No. 11 – Thin tape cut from a plastic bottle

Well, you decide for yourself what to make from such plastic tape. For example, you can weave something (a keychain or an animal).

There are many devices on the Internet to cut from bottles plastic tapes and ropes or even fishing line. Among them there are many complex devices and simple ones. But this cutter is distinguished by its ingenious simplicity and elegance. Well, you don’t need to grind any parts for it, everything is available at home or can be bought very cheaply. The main thing is that you can make it yourself in literally minutes. With it you can adjust the width of the tape and make it in different sizes.

Just look what this Chinese store has for the garden.

What tools and parts are needed to make this simple cutter?

This is the blade that will perform the actions. A stationery knife or, as in this case, a pencil sharpener will do. You need washers and 2 screws. All you need is a screwdriver.

Work progress

Using a screwdriver, remove the blade from the sharpener. And now we need to decide what width the tape will be cut from PET bottles. By combining washers, the height and width of the rope are adjusted.

For the product you will need a table into which you don’t mind driving a couple of screws. Although, you can place a board under the machine and fasten it to the table with clamps.

When a place is found cutting machine, at a distance from each other, screw in two self-tapping screws with washers. Set the blade to the desired height and tighten it with self-tapping screws.

Now we prepare a blank for cutting rope from a plastic bottle. Carefully separate the bottom using a stationery knife. The cut should be smooth. We feed the workpiece into the cutter.
We process one and a half racks with our own hands and a simple machine. To make the thread even, press a little from above. We pull the finished tape from the machine.